Installation Manual

ManualsBrandsModway ManualsFurnitureModway Stellar Vinyl Office Chair in Black

Customer Service 908-368-1025︱www.modwayfurniture.com

Page 1 of 4

EEI –2772/2653 OFFICE CHAIR

Hardware:

Component:

Thank you for purchasing the MODWAY OFFICE CHAIR！

Before you start, here is some helpful advice:

1.We suggest you spend a short time reading through this leaﬂet and then follow the simple step by step

instructions.

2.Owing to the size and weight of the oﬃce chair, we recommend that it is assembled by two adults, on a carpeted

or padded area, in the room that it is intended for. Approximate assembly time: 15 minutes.

3.Please do not use any tools other than those provided or recommended in these instructions.

4.Please do not throw away any of the packaging or instructions until you have checked all the components and

hardware and the furniture is fully assembled.

5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the

components from time to time, so please save the tools that have been provided.

6.Please keep all pieces out of reach of small children.

Bolt M8*25mm

Bolt M8*30mm

Flat Washer 8*17mm

H Castors

B Right Armrest

F Cylinder

A Chair Back X1

E Control Mechanism

Allen Wrench

C Left Armrest

G Chair Base

D Chair Seat

Summary of content (4 pages)

PAGE 1
EEI –2772/2653 OFFICE CHAIR Thank you for purchasing the MODWAY OFFICE CHAIR！ Before you start, here is some helpful advice: 1.We suggest you spend a short time reading through this leaﬂet and then follow the simple step by step instructions. 2.Owing to the size and weight of the oﬃce chair, we recommend that it is assembled by two adults, on a carpeted or padded area, in the room that it is intended for. Approxi mate assembly time: 15 minutes. 3.
PAGE 2
EEI –2772/2653 OFFICE CHAIR STEP 1: Please put Chair Base (G) upside down on a carpeted or padded surface. Insert 1pc of Castor (H) into the Chair Base (G) as shown by hand. Repeat the same steps for the remaining 4pcs of Castor (H). H H H H G H STEP 2: Flip the assembled Chair Base (G) with Castors (H) on the floor. Insert the bottom end of Cylinder (F) into the assembled Chair Base (G) as shown. F G Customer Service 908-368-1025︱www.modwayfurniture.
PAGE 3
EEI –2772/2653 OFFICE CHAIR STEP 3: Please put the Chair Seat (D) upside down on a carton. Attach Chair Right Armrest (B) and Left Armrest (C) into the bottom of Chair Seat (D) by using 4 pieces of Bolt (2) as shown. Use Allen Wrench (4) to tighten all Bolts (2) clockwise until secure. 2 2 4 2 2 B D C 4. 2. 2x4pcs Hardware & Tool required 4x1pcs STEP 4: Please put the Chair Back (A) upside down on a carton.
PAGE 4
EEI –2772/2653 OFFICE CHAIR STEP 5: Please put the assembled Chair Seat (D) upside down on a carton. Attach Control Mechanism (E) into the bottom of Chair Seat (D) by using 2 pieces of Bolt (1) and 2 pieces of Bolt (2) with 4 pieces of Flat Washer (2) as shown. Use Allen Wrench (4) to tighten all Bolts (1) and Bolts(2) clockwise until secure. 4 3 1 3 E 2 3 1 3 B 2 D C A 1. 2. 1x2pcs 3. 2x2pcs 4.