Instructions / Assembly

ManualsBrandsModuline ManualsGarage Cabinets & Storage SystemsSelect Series 75 in. H x 144 in. W x 48 in. D Aluminum Cabinet Set in Black with Stainless Steel Worktop (13-Piece)

M o d u l i n e C a b i n e t s . c o m / p d f / S e l e c t - A s s y - I n s t r . p d f

R e v i s i o n 1 F i n a l | 1 0 / 1 2 / 1 5

Moduline Modular Aluminum Cabinets

20 Holland St., Brockton, MA USA 02301

P: 888-343-4463 | F: 508-580-5199

ModulineCabinets.com

ASSEMBLY INSTRUCTIONS

Read these instructions thoroughly before assembly and keep for future reference.

TABLE OF CONTENTS

1 Check Your Order

1 Tools You’ll Need

2 Hardware We Supply

2 Before You Begin

3 Tool Boxes

3 Overhead Cabinets

3 Base Cabinets

5 Closets

7 Insta-Walls™

8 Installing Your Cabinets

9 Countertop

9 Caring For Your Cabinets

CHECK YOUR ORDER

When your order is delivered, remove the packing material and thoroughly inspect all cabinets for

damage. Every cabinet is inspected and free of defects when it leaves our facilities. If you believe your

order has been damaged, sign the bill of lading as Possible Concealed Damage or Damage and contact

your Moduline sales representative.

TOOLS YOU’LL NEED

o Level

o #2 Phillips Screwdriver

o Cordless Drill/Driver with #2 Phillips bit

o /, / & / Wehes o Rathets

o Masking Tape

o Microfiber Cloth

o Glass Cleaner

o Stainless Steel Polish

Summary of content (9 pages)

PAGE 1
Moduline Modular Aluminum Cabinets 20 Holland St., Brockton, MA USA 02301 P: 888-343-4463 | F: 508-580-5199 ModulineCabinets.com ASSEMBLY INSTRUCTIONS Read these instructions thoroughly before assembly and keep for future reference.
PAGE 2
HARDWARE WE SUPPLY A. B. C. D. E. F.
PAGE 3
TOOL BOXES Tool boxes are shipped fully assembled. To access the mounting holes you need to remove the drawers. With a drawer fully open, hold down the release levers located on the inside of both slides (see right) and pull the drawer out of the tool box. Set the drawers aside, out of the way, and reinsert them once installation is complete. OVERHEAD CABINETS Overhead cabinets are shipped fully assembled. BASE CABINETS Base cabinets require some assembly.
PAGE 4
2. Put the counter braces down between the sides and fasten each with (4) 10-24 selftapping screws [B]. B 3. Assemble the toe kick with (8) 8-32 flat-head screws [A]. A 4. Put the toe kick on top of the cabinet and fasten it with (6) 10-32 screws [C]. Leave these a little loose for shimming later. C Now flip the cabinet upright, but hold the door so it a ’t s i g ope to p e e t the a i et f o falling over. Wait to install the shelves until after the cabinets are joined together.
PAGE 5
CLOSETS Closets require some assembly. Peel back protective vinyl from contact surfaces as you go. DO NOT overtighten self-tapping screws. They will strip the holes. Moduline Select Series cabinets are assembled quickly and easily with self-tapping screws. Start your driver on a low clutch setti g a d i ease it as e essa u til s e s i stall p ope l . Batte ha ge affe ts ou d i e ’s po e , so ake su e to reset your clutch each time you change batteries.
PAGE 6
2. Put the closet top down between the sides and fasten with (11) 10-24 self-tapping screws [B]. B 3. Assemble the toe kick with (8) 8-32 flat-head screws [A]. A 4. Put the toe kick on top of the closet and fasten it with (6) 10s e s [C]. Leave these a little loose for shimming later. C Now flip the closet upright, but hold the door so it a ’t s i g ope to p e e t the a i et f o falling over. Wait to install the shelves until after the cabinets are joined together.
PAGE 7
INSTA-WALLS™ Moduline Insta-Walls are shipped i ’ wide sections. Wall stiffeners provide additional strength above the counter. Line the sections up against a wall. Insert wall stiffeners into the channels in the back of each wall section and fasten the sections together with (8) ¼-20 bolts [E]. F E Cage nuts [F] are packed separately. They allow you to mount your cabinets without needing access to the back of the Insta-Walls.
PAGE 8
One bracket has a pre-formed Z shaped end as shown. This end will fit inside the Insta-Wall channel. Bend the other end at the desi ed le gth. Fo spa es of o o e ou ill eed to olt two brackets together. Install the brackets in the top hole of the Insta-wall using (1) ¼-20 bolt [E]. Locate them at least two sections (2’) i f o the e ds so the ’ e concealed. Use as many brackets as is necessary to adequately secure your cabinets to the wall. Fasten the bracket to the wall using appropriate fasteners.
PAGE 9
COUNTERTOP Dry fit the countertop to make sure you like how it fits before using any adhesive. Cover any exposed cabinet surfaces that could be scratched moving the countertop into position, especially closet sides. It’s eas to a ide tally damage your cabinets when trying to install a countertop between two closets. If you have closets at both ends of your combo, wait to install one closet until after the countertop and overheads are installed.