Submittal Sheet

ManualsBrandsModine ManualsHeating SuppliesHD75 Hot Dawg Propane Power Vented Heater w/ Alumnized Steel Heat Exchanger (75,000 BTU)

AccuSpec V4.6.1

SUBMITTAL SCHEDULE & DATA

Gas- and Oil-Fired Unit Heaters, Infrared Heaters, and Indoor Duct Furnaces

Job Name:

Date: 10/31/2016

Location:

Engineer:

Submitted by: Jeff Musto

Architect:

Contractor:

Unit Tag

Model Number

HD 75AS0121FBAN

Quantity of Units

Btu/Hr Input

75,000

Btu/Hr Output

61,500

CFM

1160

Altitude

0-2000

Temperature Rise (degrees F)

External Static Pressure (E.S.P)

0.00

Total Static Pressure (T.S.P.)

0.00

Gas Type

Propane

Gas Control Type

Single Stage, Direct

Spark Ignition, 100%

Shut-Off with

Continuous Retry

Supply Voltage

115/60/1

Control Voltage

24V

Motor HP

1/12

Motor RPM

1625

Blower RPM

N/A

Heat Exchanger Type

Aluminized Steel Heat

Exchanger/Burner

Options & Accessories (See

Attached Pages)

Remarks___________________________________________________________________________________

__________________________________________________________________________________________

Summary of content (7 pages)

PAGE 1
AccuSpec V4.6.1 SUBMITTAL SCHEDULE & DATA Gas- and Oil-Fired Unit Heaters, Infrared Heaters, and Indoor Duct Furnaces Job Name: Location: Submitted by: Jeff Musto Date: 10/31/2016 Engineer: Architect: Contractor: Unit Tag Model Number Quantity of Units Btu/Hr Input Btu/Hr Output CFM Altitude Temperature Rise (degrees F) External Static Pressure (E.S.P) Total Static Pressure (T.S.P.
PAGE 2
AccuSpec V4.6.
PAGE 3
AccuSpec V4.6.
PAGE 4
AccuSpec V4.6.1 GENERAL PERFORMANCE DATA General Performance Data Model At 0’ Elevation Btu/Hr. Input Btu/Hr. Output Entering Airflow (CFM) Outlet Velocity Air Temp. Rise (°F) Mounting Height (Max Ft.)1 Heat Throw (Max. Mtg. Ft.) 2 Unit Total Power (Amps) HD 75 75,000 61,500 1160 769 48 14 38 3.25 As Configured at 0-2000 Ft. Elevation Btu/Hr. Input 75,000 Btu/Hr. Output 61,500 Configured Air Temp Rise (°F) 49 Motor Data Horse Power RPM Type Motor Amps at 115V 1/12 1625 P.S.C. 1.
PAGE 5
AccuSpec V4.6.1 DIMENSIONS – UNIT Model HD Dimensions Model Size Dimensions (in inches) A B C D E F G H I J Vent Connector Diameter Gas Connection Diameter Fan Diameter Approx. Shipping Weight HD75 26.8 18 16.5 14.9 15.9 10.7 18.5 7.8 31 25 3 1/2 14 85 lbs.
PAGE 6
Standards All unit(s) shall include: C.S.A. (Canadian Standards Association) design certification for use in both the US and Canada to the ANSI Z83.8 - latest revision, standard for “Gas Unit Heater and Gas-Fired Duct Furnaces” for safe operation, construction, and performance Mechanical Configuration Furnace(s) section with 82% minimum efficiency provided by an indirect-fired tubular heat exchanger with individually fired tubes for maximum heat transfer with minimal noise of flame ignition/extinction.
PAGE 7
An automatic reset high limit switch mounted in the air stream to shut off the gas supply in the event of overheating. A time delay relay that delays the start of the air mover to allow the heat exchanger a warm-up period after a call for heat. The time delay relay shall also continue the air mover operation after the thermostat has been satisfied to remove any residual heat in the heat exchanger. The unit shall be orificed for 0-2000 feet elevation above sea level.