Installation Sheet

1 3/4" 1 3/8"
4 1/8"
15
3
4
"
Back Plate Dimensions
2
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
PREPARATION
clear area. Be careful not to lose any small parts necessary for
installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (C) from the mounting back
plate.
4. Drill holes in the wall aligned with the key holes located in the
mounting back plate, insert the plastic anchors (G).
5. Connect the Driver’s
input wires to junction box wires as
shown in Fig. 2, making sure that all wire connectors (A) are
secured. If your outlet box has a green or bare copper ground
using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
* Requires Driver
to be recessed within the junction box
MOUNTING THE FIXTURE (Fig. 1)
6. Secure the mounting back plate to the junction box using
junction box screws (B), fasten it to the wall using wood screw
(H). The side of the mounting back plate marked “GND” must
face out.
7. Connect the driver’s
Fig.2, making sure that all wire connectors (D) are secured.
mounting screw (C).
using Allen wrench(F).
INSTALLATION INSTRUCTION
– LED Wall Sconce
WS-44835
Fig.1
C
E
F
B
A
G
H
D
Wire Connector
Wood Screw
Plastic Anchor
Wire Connector
Junction Box
Driver
2.7/8”[L]x1.1/4”[W]x1.1/8”[H]
Junction Box Screw
Mounting Plate
Allen Wrench
Allen Screw
Mounting Screw
Glass
(RPL-GLA-44835)
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
I
Glass
(RPL-GLA-30835)
Wire Connector
Junction Box
Junction Box
Screw
Mounting Screw
Wood Screw
Plastic Anchor
Allen Wrench
Allen Screw
B
C
F
G
D
E
A
Mounting Plate
Female/Male end connector
7. Connect the driver’s(H)output wires to the fixture by Female/
Male end connector as shown in Fig.2.
7MBC401003
H
(E).
(D)
(G)
(F)
(H)
(H)
1
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
INSTALLATION INSTRUCTION
– LED Wall Sconce
WS-
835
WARNING
.gnillatsni erofeb snoitcurtsni lla daeR-
”FFO” hctiws ro )s(esuf eht wercsnu dna noitisop ”FFO“ eht ni hctiws rewop niam eht ecalP .rekaerb tiucric ro ,xob esuf niam eht ot oG-
.noitisop ”FFO“ eht ni hctiws llaw eht ecalP-
CAUTION
tuo nrow era taht strap yna esu ro ,tuo strap evael ,strap yna etutitsbus ton oD .snoitcurtsni eseht ni detacidni sa desu eb tsum strap llA-
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
.rellatsni’d tnava snoitcurtsni sel setuot zesiL-
locaux.
têrra’d noitisop ne lapicnirp ruetpurretni’l zecalp te eruemed ertov ed selbisuf ed uo sruetcnojsid ed lartnec uaennap ua zedéccA-
(« OFF »).
.)» FFO «( têrra’d noitisop ne larum ruetpurretni’l zecalP-
MISE EN GARDEs
te étôc ed sap zessial ne’n ,secèip sel sap zecalpmer eN .snoitcurtsni sec snad éuqidni tse li’uq let seésilitu ertê tneviod secèip sel setuoT-
ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire.
MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPO
RTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
atse ed nóicalatsni e ejalbmasne le noc redecorp ed setna otelpmoc rop senoicartsuli e senoiccurtsni sal sadot adnerpmoc y aeL-
lámpara.
lapicnirp nóicatnemila ed rotpurretni le euqoloC .ragoh us ne lapicnirp otiucric ed rotpurretni led ajac al a o selbisuf ed ajac al a esajíriD-
en la posición “OFF” (APAGADO).
.)ODAGAPA( ”FFO“ nóicisop al ne derap al ed rotpurretni le euqoloC-
PRECAUCIÓN
in nóicalatsni al etnarud sazeip atimoon ,sazeip sal ecalpmeer oN .senoiccurtsni satse nacidni ol omoc esrasu nebed sazeip sal sadoT-
PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
Wire Connector
Qty: 3pcs+1 Extra
7EAC112201
A
Mounting Screw
Qty:1 Extra
4MPF0412S2BB1(BB)
5/32”-32x1/2
Burnished Brass
C
Rubber Gasket
Qty:2PCS+1 Extra
7EAC140901
D
Allen Screw
Qty: 8pcs+1 Extra
7MPF0408K2
5/32”-32 x 5/16
Nickel Plating
Allen Wrench
Qty:1pc
7MPE205001
Nickel Plating
Plastic Anchor
Qty: 2pcs+1 Extra
7TDD082401
Wood Screw
Qty: 2pcs+1 Extra
7MPF2204J2
Ø4X22
E F G H
Junction Box Screw
Qty: 2pcs+1 Extra
7MPF0415C2
#8-32x9/16 SS
B
G0
Driver
Qty:1pc
LD-
0MA U-IS-P
I
10. Insert the crystal into the ÿxture, secure it with Allen screw (E)
using Allen wrench(F).
9.
mounting screw (C).
8. Hook the safety cord to the mounting back plate.
Glass
(RPL-GLA-30835)
Wire Connector
Junction Box
Junction Box
Screw
Mounting Screw
Wood
Screw
Plastic Anchor
Allen Wrench
Allen Screw
B
C
F
G
D
E
A
Mounting Plate
Female/Male end connector
Safety Cord