Installation Sheet

2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
131 - LED Flush Mount
FM-13114
PREPARATION
1.
2.
CONNECTING THE WIRES (Fig. 2)
3.
4. Drill holes in the ceiling aligned with the key holes located in the mounting plate, insert the plastic anchors (D1).
5. Fig. 2, making sure that all wire connectors (A1) are secured.
back plate using the green screw provided.
After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
6. Secure the mounting plate to the junction box using junction box screws (B1),
fasten it to the wall using wood screw (E1). The side of the mounting back
plate marked “GND” must face out.
7.
8.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Plastic Anchor
Wire Connector
Wood Screw
Junction Box Screw
Mounting Screw
Fixture Shade
Mounting Plate
Junction Box
Glass
(RPL-GLA-13114)
Shade
(RPL-SHA-13114)
D1
A1
E1
B1
C1
FIG. 1
Ø 7"
Back Plate Dimensions
G
N
D
Ø 8 3/4"
Ø 2 3/4"
Ø 3 1/2"
PD-16818,PD-16824,PD-16830
168-LED Flush Mount
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
8-32x1 SS 8-32x9/16 SS Nickel Plating
Junction Box
Mounting Plate
Canopy
Stem
Fixture
Shade
PC Diffuser
Glass
(RPL-GLA-13114)
(RPL-GLA-13120)
(RPL-GLA-13126)
Shade
(RPL-SHA-16818)
(RPL-SHA-16824)
(RPL-SHA-16830)
Diffuser
(RPL-DIF-13114)
(RPL-DIF-13120)
(RPL-DIF-13126)
PD-16818 4 3/4"
PD-16824 4 3/4"
PD-16830 4 3/4"
PD-16818 4 3/4"
PD
-16
8
24
4 3/4"
PD-16830 4
3/4
"
PD-
1
6818 2 -1/2"
PD-
1
682
4 2 -
1
/
2"
PD-1
68
30 2
-
1/2"
G0
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
Junction Box
Mounting Plate
Canopy
Stem
Fixture
Shade
PC Diffuser
Glass
(RPL-GLA-13114)
(RPL-GLA-13120)
(RPL-GLA-13126)
Shade
(RPL-SHA-16818)
(RPL-SHA-16824)
(RPL-SHA-16830)
Diffuser
(RPL-DIF-13114)
(RPL-DIF-13120)
(RPL-DIF-13126)
PD-16818 2-1/2"
PD-16824 2-1/2"
PD-16830 2-1/2"
PD-16818 4 3/4"
PD-16824 4 3/4"
PD-16830 4 3/4"
3. Remove the mounting screw (C) from the xture.
5. Choose number of rods suitable for your application.
6. Thread the xture wire through the rods and canopy.
7. Connect the canopy, rods and lamp body. Make sure all are tightened.
8. Cut the extra wire. Connect the xture’s input wires to junction box wires as
shown in Fig.2, making sure that all wire connectors (A) are secured. If your
outlet box has a green or bare copper ground wire, connect the xture’s
ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
9. Insert the PC diuser into the xture shade.
4. Secure the mounting plate to the junction box using junction Box screws(B).The side of the mounting back plate marked “GND”
must face out.
MOUNTING THE FIXTURE (Fig. 1)
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.
PREPARATION
CONNECTING THE WIRES (Fig. 2)
COMPLETING THE INSTALLATION (Fig. 1, 2)
10. Secure the xture onto mounting plate with mounting Screws(C).
11. For slope ceiling application, rotate wire at the top of
the stem to ensure luminaries is aiming down.
Secure the mounting plate to the junction box using junction box screws (B1),
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
PD-34865
348-LED Pendant
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
PREPARATION
Fig.1 Fig.2
Fig.3 Fig.4
O
Allen Wrench
P
Allen Screw
F
Drop Hanger
G
Decorative Ring
E
2 e
Plastic Anchor
N
Wire Clamp
K
Fixture
Fixture
Tube_B Setion
B
D
Tube_D Setion
L
M
K
K
Tube_C Setion
C
Tube_A Setion
A
Transformer
2 3/8" " "
Transformer
2 3/8" "
Ground Wire
Junction Box
Mounting Plate
H
Wire C nect r
Transformer
2 3/8" [L 2
" [W] x
"
[ ]
J
M unting Screw
Fixture
I
Juncti n B x Screw
Cable Gripper
J
K
Mounting Screw
QTY: 1 Extra
7MPF0412S1(NI)
#8-32x1/2
Nickle Plating
Lighting Section
QTY:5pcs
with two Connctors
Lighting Section
QTY:1pcs
with male Connctors
Lighting Section
QTY:1pcs
with female Connctors
L
M
N
P
QTY:2pcs+1Extra
4MPE090602NI
Nickle Plating
Wire Clamp
Allen Screw
Qty: 4pcs+1 Extra
7MPF0303K1
1/8"-40×1/8
Nickel Plating
Allen Wrench
Qty: 1 Extra
7MPE155003
O
617 - LED Pendant
PD-61760
Back Plate Dimensions
7MBC382501
Fig.1
3. Remove the mounting screw (G) and Mounting
Back Plate from the xture.
7. Drill holes in the wall aligned with the key hole located in
the mounting plate, insert the plastic anchor (A).
8. Secure mounting back plate to the junction box using
junction box screws (D), fasten it to the wall using wood
screw (B) The side of the mounting plate marked “GND”
must face out.
* Hook the two hooks on the mounting back plate slot.
Note: The fixture exceeds 100 lbs. and must be installed using an
outlet box U.L. approved for 200lbs.
9. Connect the driver input wires with outlet box wires, making
sure that all wire connectors (C) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s
ground wire to it. Otherwise, connect the xture’s ground wire
directly to the mounting plate using the green screw provided.
After wires are connected, tuck them carefully inside the junction
box.
10. Connect the driver output wires with xture wire as shown in Fig.2,
making sure that all wire connectors (C) are secured.
11. Place the xture over the mounting back plate and secure it with
mounting screws (G).
12. The lamp ring can rotate 350 degree; rotate them to your desired
angles.
4. Remove two hoods from the safety cord; choose
the number of down rods suitable of your application.
5. Thread the two safety cords and xture wire through
the rods and canopy one by one. Connect the canopy,
rods and
xture body. Making sure all are tightened.
6. Unscrew the Allen screw (F) using Allen wrench (E), pull
out the extra safety cord through clamp, leave a loop for
hooking, then secure the safety cords with clamp by
tightening the Allen screw, hook the hooks into the safety
cord loop.
CONNECTING THE WIRES (Fig. 2)
1. Shut o the power at the circuit breaker and
remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out
all the parts on a clear area. Be careful not to
lose any small parts necessary for installation.
PREPARATION
Rod
350°
350°
350°
350°
Mounting Screw
G
Canopy
Mounting Back Plate
Junction Box
D
F
E
Wire Connector
C
Driver
8-7/8" to 9-7/8"
x 3-9/16" x 1-3/4"
Clamp
Plastic Anchor
A
B
Wood Screw
Cable( Red/Black)
Hook
Pull
Safety Cords
U.L. Approved 200LB. Max.
Outlet Box and Hardware
( Sold Separately )
1 3/8”
15 1/4”
1 3/4”
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fig. 3
(Ground)
Fig. 3
Turn to down
1
3
8
"
1
3
4
"
Back Plate Dimensions