Installation Guide

2
INSTALLATION INSTRUCTIONS
599- LED Pendant
PD-59922/PD-59933
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
FIG. 1
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous impro
vement program. Mar 2019
JANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture,
including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and back plate from the fixture.
4. Drill holes in the wall aligned with the key holes located in the
mounting back plate, insert the plastic anchor (D).
5. Secure mounting back plate to the junction box using junction box
screws
. Fasten it to the wall using wood screw (C).
NOTE: The side of the mounting plate marked “GND” must face out.
6. Adjust the fixture wire length by pushing the cable-gripper on the
canopy and pulling the wire as desired.
a. Retract the wires close to the desired length within the canopy
before securing the fixture in place.
NOTE: Using the cable gripper to adjust more than 18” of wire
length is not recommended.
WARNING: Shortening the cables without professional helps or
electronic background is not advisable. Any modifications to
the fixture will result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig. 2)
7. Connect the driver’s input wires to junction box wires as shown (Fig. 2
). Make sure that all wire connectors (A) are secure. If your outlet box
has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the
back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Hook the safety cords to the back plate.
9. Place the fixture over the mounting back plate and secure it with mounting screws (B).
NOTE: This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming
wiring information.
COMPLETING THE INSTALLATION
10. Secure the fixture to the mounting back plate using the mounting screw (B) .
11. Hook the safety cords to the lamp body, attach the petal shade on the lamp body using internal magnet.
DIMMING WIRING INSTRUCTIONS (Fig. 3)
12. To utilize ELV or TRAIC dimming: use black (hot), white (neutral) and bare copper ground wire (ground).
13. To utilize 0-10V dimming: use purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
NOTE:
Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
FIG. 3 Driver Wires
White - Neutral
Black - Hot
Purple - Dim+
Gray - Dim-
Red - Fixture+
Black - Fixture-
PD-59922/PD-59933 Back Plate
Junction Box
White Wire
Black Wire
Wire Connector
A
Mounng Back Plate
Wood Screw
C
Plastic Anchor
D
Junction Box Screw
Mounting Screw
B
Safety Cords
Driver(Canopy Inside)
4"L*4"W*5/8"H
Petal Shade
Safety Cords
(Only PD-59933)
Bare Copper Ground Wire
Push up
Cable-gripper
Instructions: Adjust the
fixture wire length by
pushing the cable-gripper
on the canopy and
pulling the wire as
desired.
Lamp Body
Ø8
3
4
"
Ø5
7
8
"
1
3
8
"
1
3 4
"
2
1
2
"
1
1 2
"