Installation Sheet

2
INSTALLATION INSTRUCTIONS
550-LED Pendant
PD-55024/55036/55048
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring Fig. 3 Back Plate Dimensions
Fig. 1
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture,
including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Drill holes in the wall aligned with the key holes located in the back
plate, insert the plastic anchor (D)
5. Secure back plate to the junction box using standard junction box
screws that comes with the junction box. Fasten it to the wall using
wood screw (C) onto the plastic anchor. Note: the side of the mounting
plate marked “GND” must face out.
6. Adjust the fixture wire length by pushing the cable gripper on the
canopy and pulling the wire as desired.
a. Retract these wires close to a desirable length to within the
canopy before securing the fixture in place.
Note: retracting or extending excessive cable length through
the cable gripper is not recommended.
b. Warning: Shortening these cables without professional helps
or electronic background is not advisable. Any modifications
to the fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig. 2)
7. Connect the driver input/output wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) (C)are secured. If
your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground
wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wiring
information.
9. Secure the fixture to the back plate using the mounting screw (B).
NOTE: DIMMING WIRING INFORMATION (Fig. 3)
10. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wires
information.
11. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
12. To utilize 0-10V dimming: use wir e purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
D
C
A
B
Fixture
Driver
Ground wire
Junction Box
Back plate
Plastic anchor
Wire connector
Safety cood
PS:PD-55048
Junction box screw
Wood screw
Mounting screw
Cable-gripper
Push up
Adjust the fixture wire length by
pushing the cable gripper on
the canopy and pulling the wire
as desired.
Φ 6 3/4”
1 3/8”
1 3/4”