Installation Sheet

INSTALLATION INSTRUCTIONS
PD-53047
530 – LED Pendant
2
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Cable-gripper
Push up
Fixture
Black W ire
White
W ire
Junction Box
Screw
Wire Connector
Ground Wire
Junction Box
Mounting Plate
Plastic Anchor
Wood
Screw
Mounting Screw
Flat Driver
A
C
D
B
Back Plate Dimensions
Fig.1
11
3
4
"
1
3
4
"
5
7
8
"
4
1
4
"
1
3 8
"
8
1
8
"
Fig.3
White - Neutral
Black - Hot
Purple - Dim+
Grdy - Dim-
Red - Fixture+
Black - Fixture-
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture,
including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (B) from the fixture.
4. Drill holes in the wall aligned with the key holes located in the
mounting plate, insert the plastic anchor(C).
5. Connect the driver input wires with junction box wires
as shown in Fig.2, making sure that all wire connectors (A)
are secured. If your outlet box has a green or bare copper
ground wire, connect the fixture’s ground wire to it.
Otherwise, secure the fixture’s ground wire directly to
the mounting plate with the green screw provided.
After wires are connected, tuck them carefully inside
the junction box.
MOUNTING THE FIXTURE (Fig. 1)
6. Secure mounting plate to the junction box using junction
box screws , fasten it to the wall using wood screw(D).
Note: the side of the back plate marked “GND” must face out.
7. Adjust the fixture wire length by pushing the cable gripper on the
canopy and pulling the wire as desired.
Adjust the fixture wire
length by pushing the
cable gripper on the
canopy and pulling
the wire as desired.
a. Retract these wires close to a desirable length within the canopy
before securing the fixture in place. Using the cable gripper to
adjust more than 18” of wire length is not desirable.
b. Warning: shortening these cables without professional helps or
electronic background is not advisable. Any modifications to the
fiture will result in voiding the warranty of the product.
8. Place the fixture over the mounting back plate and secure it with
mounting screws(B).
DIMMING WIRING INFORMATION (Fig. 3)
9. This fixture features electronic low
voltage (ELV or TRAIC) or 0-10V
dimming capabilities. See notes
below for specific dimming wires
information.
10. To utilize ELV or TRAIC dimming:
use wires black (hot), white (neutral)
and bare copper ground wire (ground).
11. To utilize 0-10V dimming: use wire
purple (dim+), gray (dim-), black (hot),
white (neutral) and bare copper
ground wire (ground).
NOTE: Make sure to connect 0-10V
prior to power-up the fixture in order
to allow the 0-10V dimming to function
properly.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring