Installation Sheet

2
INSTALLATION INSTRUCTIONS
248-LED Pendant
PD-24848
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
FIG. 1
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am.
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture,
including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and back plate from the fixture.
4. Drill holes in the wall aligned with the key holes located in the
mounting back plate, insert the plastic anchor (C).
5. Secure the mounting back plate to the junction box using
standard junction box screws, fasten it to the wall using
wood screw (D). Note: the side of the mounting plate marked
“GND” must face out.
6. Adjust the fixture wire length by pushing the cable gripper on
the canopy and pulling the wire as desired.Retract these wires
close to a desirable length to within the canopy before securing
the fixture in place.
Note: retracting or extending excessive cable length through the
cable gripper is not recommended.
Warning: Shortening these cables without professional helps or
electronic background is not advisable. Any modifications to the
fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig. 2)
7. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to
the back plate using the green screw provided. After wires are
COMPLETING THE INSTALLATION
8. Hook the safety cords to the stents.Secure the fixture to the mounting back plate using the mounting screw (B) .
9. After installed , adjust the outer ring like the graphical( FIG.1)position.
DIMMING WIRING INFORMATION (Fig. 3)
10. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wires
information.
11. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral).
12. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot), white (neutral).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
Back Plate Dimensions Fig. 3 Driver Wires
Junction Box
:LUH&RQQHFWRU
A
Ground Wire
3ODVWLF$QFKRU
C
:RRG6FUHZ
D
-XQFWLRQ%R[
6FUHZ
Back Plate
Safety Cords
Driver
3 1/2"LX2 3/8"WX1 1/4"H
0RXQWLQJ
6FUHZ
B
3XVKXS
&DEOHJULSSHU
Adjust the fixture wire
length by pushing the cable
gripper on the
FDQRS\DQGSXOOLQJWKH
ZLUHVDVGHVLUHG
.
1
3
8
"
1
3
4
"
7
7
8
"
Ø8
1
8
"
Ø7
1
2
"
Purple - Dim+
Gray - Dim-
Black - Hot
White - Neutral
Red - Fixtrue+
Black - Fixtrue-