Installation Guide

2
INSTALLATION INSTRUCTIONS
119-LED Pendant
PD-11912-T24
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fig. 1
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture,
including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and back plate from the fixture.
4. Adjust the fixture wire length by pushing the cable-gripper on the
canopy and pulling the wire as desired.
a. Retract the wires close to the desired length within the canopy
before securing the fixture in place.
NOTE: Using the cable gripper to adjust more than 18” of wire
length is not recommended.
WARNING: Shortening the cables without professional helps or
electronic background is not advisable. Any modifications to the
fixture will result in voiding the warranty of the product.
5. Secure the mounting back plate to the junction box using the
screws provided with the the junction box.
NOTE: T
he side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
6. Connect the driver input wires with junction box wires as shown (
Fig.2). Make sure that all wire connectors (A) are secure. If your
outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
7 Secure the fixture to the mounting back plate using the mounting screw (B) .
DIMMING WIRING INSTRUCTIONS (Fig. 3)
8. To utilize ELV or TRAIC dimming: use black (hot), white (neutral) and bare copper ground wire (ground).
9. To utilize 0-10V dimming: use purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
NOTE:
Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
Junction Box
Mounting Screw
B
Mounting Plate
Junction Box Screw
fi
Push up
Cable-gripper
Fixture
Top Glass
(RPL-GLA-11912)
Bottom Glass
(RPL-GLA-11912-02)
Wire Connector
A
Driver 4"Lx4"W x5/8"H
Back Plate Dimensions
1 3/8"
1 3/4"
∅5 1/2"
White - Neutral
Black - Hot
Purple - Dim+
Gray - Dim-
Red - Fixture+
Black - Fixture-
Fig. 3 Driver Wires
NOTE: This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See
notes below for specific dimming wiring information.