Installation & Assembly

2
INSTALLATION INSTRUCTIONS
739-LED Pendant
PD-73926/ PD-73932
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
FIG. 1
Mounting Back Plate Dimensions
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous impro
vement program. Jan 2019
ANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
3
8
″
Ø5
3
8
″
1
3 4
″
Push up
Junction Box
Mounting Plate
Fixture
Wire Connector
A
Junction Box Screw
B
Mounting Screw
Driver 3 3/8” L x 2 3/8” W x 1 1/8”H
Cable-gripper
Safety Cords
FIG. 3
3. Remove the mounting screw (B) and back plate from the fixture,.
4. Adjust the fixture wire length by pushing the cable
-gripper on the canopy and pulling the wire as desired. Make sure the wires are the
same length.
a. Retract the wires close to the desired length within the canopy before securing the fixture in place.
NOTE: Using the cable-gripper to adjust more than 18” of wire length is not recommended.
WARNING: Shortening the cables without professional help or electronic background is not advisable. Any modifications to the
fixture will result in voiding the warranty of the product.
5. Secure the mounting back plate to the junction box using
the screws provided with the junction box.
NOTE: The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
PREPARATION
7. Connect the driver input wires with junction box wires as shown
(Fig.2). Make sure that all wire connectors (A) are secure. If your outlet box
has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the
mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Secure the fixture to the mounting back plate using the mounting screw (B) .
9.
To utilize 0-10V dimming: use purple (dim+), gray (dim-), black (hot), white
(neutral) and bare copper ground wires (ground).
NOTE: DIMMING WIRING INSTRUCTIONS (Fig. 3)
Purple - Dim+
Gray - Dim-
Black - Hot
White - Neutral
6 . Properly secure the safety cord to the bracket on mounting back plate to temporary hang the fixture in place.
CONNECTING THE WIRES (Fig. 2)
-
Instructions: Adjust the fixture wire
length by pushing the cable-gripper on
the canopy and pulling the wire as
desired.
NOTE:
This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below
for specific dimming wires information.
10. To utilize 0-10V dimming: use purple (dim+), gray (dim-), black (hot), white
(neutral) and bare copper ground wire (ground).
NOTE:
Make sure to connect 0-10V prior to powering up the fixture in order to
allow 0-10V dimmer to work properly.