Installation Guide

Mounting Ring Dimensions
Conversion Plate Dimensions
Ø
4
″
1 3/8″
1 3/4″
4 1/2″
6″
Mounting Plate Dimensions
10 7/8″
2 5/8″
1 5/8″
1 3/8″
1 3/8″
1 5/8″
7 1/2″
3
INSTALLATION INSTRUCTIONS
249-LED Wall Sconce
BL-24959
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous impro
vement program. Jan 2019
ANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
7. Secure the mounting plate to the switch box using the junction box screw. Fasten it to the wall using wood screw (B) and plastic anchor
8. Connect the driver output wires with the fixture by Female/Male end connector.
9. Place the fixture over the mounting plate, and secure it with mounting screw (D).
10. NOTE: This fixture features electronic low voltage (ELV or TRAIC) or 1-10V dimming capabilities. See notes below for specific
dimming wiring information.
OR
MOUNT ON JUNCTION BOX (Fig. 2)
3. Remove the mounting screw (D) from the fixture.
4. Secure the fixture tail (E) to screw into the fixture’s tube.
5. Drill holes in the wall aligned with the key holes located in the mounting plate, insert the plastic anchor (C).
6. Secure the mounting plate to the conversion plate (H) using the conversion plate screw (G).
7. Connect the driver's (F) input wires with junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your
outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Secure the mounting ring (I) to the junction box using the screws provided with the junction box. Make sure the two holes (spacing 2-3/4")
are horizontal as shown (Fig. 2).
9. Secure the mounting plate and conversion plate (H) to the mounting ring using junction box screws. Make sure the two holes (spacing
2-3/4") are horizontal as shown (Fig. 2). Connect the driver output wires with the fixture by Female/Male end connector.
(C).
NOTE: The side of the mounting plate marked "GND" must face out.
NOTE: This fixture requires the driver to be recessed in the junction box.
NOTE: The side of the mounting plate marked "GND" must face out.
10. Place the fixture over the mounting plate, and secure it with mounting screw (D).
NOTE: This fixture features electronic low voltage (ELV or TRAIC) or 1-10V dimming capabilities. See notes below for specific dimming
wiring information.
DIMMING WIRING INSTRUCTIONS (Fig. 4)
11. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wires (ground).
12. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wires
(ground).
NOTE: Make sure to connect 0-10V prior to powering up the fixture in order to allow the 0-10V
dimming to function properly.