Ambiance Wall Hung Electric Fires Packing Check List Package 1 1 x Electric Fire 1 x Glass Face 1 x Remote Control Handset 2 x AAA Batteries 1 x Instructions Booklet 1 x Wall Fixing Plate 1 x Fasteners Package Package 2 1 x Fire Face (Stone Face Models only) INSTRUCTION BOOKLET MUST BE LEFT WITH THE USER MODERN FLAMES 3423 EAST ATLANTA PHOENIX, ARIZONA 85040 WWW.MODERNFLAMES.
Ambiance Wall Hung Electric Fires INSTALLATION INSTRUCTIONS This Electric Fire must be installed by a qualified, competent installer. A. Location 1. The fire must not be in contact with any combustible materials. 2. The heater, which is located at the base of the fire, must be a minimum of 16 inches away from any combustible material. 3. It is important that the wall on to which the fire is to be installed is of sound construction.
B. Installation PLEASE READ THROUGH THE INSTALLATION INSTRUCTIONS BEFORE BEGINNING THE INSTALLATION. Figure 1 1. Select the position of the fire on the wall to which it is to be mounted. Draw a level horizontal line on the wall at the required height. This line will correspond to the top of the appliance so it is important to allow for the extra height of the fire front. 2. Mark the center line of the fire on to the horizontal line 3.
7. The mounting plate has four location pins, one at each corner of the plate. See Figure 1. 8. Lift the fire and place the keyhole slots situated on the back of the fire (Figure 2) to the location pins on the mounting plate. A gentle downward pressure should be applied. Make sure all of the pins have been located into the top section of each keyhole fixing slot.
C. Electrical Work THIS PRODUCT MUST BE GROUNDED 1. A standard electrical outlet must be close to the fire. If the electric outlet is required to be concealed, it can be located above or on the right hand side of the fire and behind the face. 2. DO NOT INSTALL THE FIRE WHERE THE HEATER IS DIRECTLY ABOVE THE PLUG SOCKET. The heat outlet is located in the center at the base of the fire. 3. If the power supply cable becomes damaged in any manner it MUST be replaced. 4.
D. Attaching The Face 1. On each side of the fire are two locating studs (Figure 5). 2. On the back of the face there are two brackets which hook over these studs. 3. Lift the face up to the fire. Two people may be required to carry out this installation. Then lower the face into place so that the brackets on the rear of the face locate either side of the studs on the fire. Once in place firmly screw into place the locking bolt.
Ambiance Wall Hung Electric Fires OPERATING INSTRUCTIONS Please read these instructions carefully before attempting to use the appliance and retain for future use. CAUTIONS: 1. When the fire is in operation certain areas of the fire will get hot. Caution must be taken to avoid being burned. Don’t touch hot surfaces. 2. The fire must not be switched on if volatile vapours are present in the room 3. Children must be supervised around the fire. 4. Do not obstruct the air flow around the appliance. 5.
Remote Control L O W DIMMER A Infrared Window C Flame Effect Dimmer E Heater Low Heat B D H I G H ON/OF On/Off Switch Heater Maximum Heat Prior to use, the remote control handset requires installation of 2 x AAA batteries, as supplied. (Figure 8) Remove the cover on the rear of the remote handset by sliding backwards. Install the batteries as shown and then slide the cover back into the original position. To enable the remote control to function the power to the fire must be switched on.
E Heater Low Heat (750 w) Press this once to switch to high heat. The indicator light will come on as well as the fan. Press again to turn off. (The fan will continue to run for a few moments until sensors indicate cool condition) F Indicator Lamps will verify current condition. If you are unsure if heat is on or off check the lamps on the control panel. If the function is on the indicator lamp will light above the function switch.
Modern Flame Wall Hung Electric Fires MAINTENANCE INSTRUCTIONS To Change A Light Bulb Disconnect power supply before beginning any maintenance. Light bulbs need to be replaced when you notice a dark section of the flame or when clarity and detail of the coal effect disappears. Unscrew the locking nut on the side of the brackets and then remove the face. This is done by lifting the face up and swinging the face clear of the fire. Care should be taken not to damage the face.
WARRANTY In the unlikely event of a problem occurring due to a manufacturing fault within 24 months from the date of purchase of the appliance it will be repaired or replaced free of charge. Repair or replacement is at the option of Modern Flames. Defects must be brought to the attention of Modern Flames Technical Service Department by contacting Modern Flames at (602) 268-9353 or 3423 E. Atlanta Ave, Phoenix, AZ 85040.
