X The HiRes Video Company ExtIO Opens New Horizons for Cameras Ethernet In2+ Terminal Block 1 IN2 In150 mA Out2+ Out2- LineOut+ LineOut- In2In1+ In1Out2+ Out1+ Out2Out1- Galv. separated, 50 V max. 12-24 V GND In2+ Out2 IN1 In1+ Out1 Standard EIA/TIA 568B In2- 50 mA Out1+ Out1- LineIn+ LineIn12-24 V Terminal Block 2 LineOut+ US LineOut- B GND Ca ble LineIn+ Order # USB Cable LineInreserved M12: D12: M22M: D22M: Function USB +5V USB DUSB D+ GND ø 120 mm/4.
MOBOTIX ExtIO User Manual Notes Note: MOBOTIX offers inexpensive seminars that include a workshop and practical exercises: Basic Seminar three days, Advanced Seminar two days. For more information, please visit www.mobotix.com. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
1/76 MOBOTIX ExtIO User Manual EXTIO USER MANUAL 1 INTRODUCTION 4 1.1 MOBOTIX ExtIO Concept 6 1.2 The MOBOTIX ExtIO and MOBOTIX Cameras 1.2.1 Functional Overview of the ExtIO 1.2.2 Comparison ExtIO/CamIO 8 8 9 1.3 Accessories 10 2 MOUNTING THE EXTIO 12 2.1 2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 Preparing the Installation Mounting to a Wall or Ceiling Connecting via Network or USB Mounting Options Providing the Camera Connections, Wall Outlets Directions for Mounting 12 13 13 14 14 15 2.2 2.2.1 2.
2/76 MOBOTIX ExtIO User Manual 2.8 2.8.1 2.8.2 2.8.3 2.8.4 2.8.5 2.8.6 Important Notes Safety Regulations Suitable Cables for the MOBOTIX ExtIO Safety Notes for Operating the MOBOTIX ExtIO Weatherproofness, Temperature Range Cleaning Instructions Additional Information 50 50 50 51 52 52 52 3 OPERATION OF THE EXTIO 54 3.1 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 3.1.
MOBOTIX ExtIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
4/76 MOBOTIX ExtIO User Manual 1 *You can use the ExtIO with all MOBOTIX IT and Secure models. MOBOTIX Q22M models can only be connected to the ExtIO using Ethernet. INTRODUCTION The MOBOTIX ExtIO is the weatherproof, compact expansion and connection box for connecting all MOBOTIX cameras (IT and Secure models).
MOBOTIX ExtIO User Manual © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
6/76 MOBOTIX ExtIO User Manual 1.1 MOBOTIX ExtIO Concept Simple Installation When designing the MOBOTIX ExtIO, special focus was placed on easy installation of the expansion box. The supplied drilling template facilitates mounting the ExtIO and makes connecting the cabling for data and audio connections easy, secure and weatherproof. Buttons The two buttons of the ExtIO can be used to control its two signal outputs, for example.
7/76 MOBOTIX ExtIO User Manual Using External Sensors Using the two galvanically separated signal inputs of the ExtIO, the MOBOTIX camera can monitor external sensors and apply the different mechanisms available to the camera for storing audio/video and for sending notification messages. Weatherproofness The weatherproofness of the MOBOTIX ExtIO has been tested extensively; the ExtIO reaches protection class IP65 (absolutely dustproof and resistant against water jets).
8/76 MOBOTIX ExtIO User Manual 1.2 The MOBOTIX ExtIO and MOBOTIX Cameras ExtIO MX-EXTIO 1.2.1 Functional Overview of the ExtIO *IEEE 802.3af required You can use the ExtIO with all MOBOTIX IT and Secure models. MOBOTIX Q22M models can only be connected to the ExtIO using Ethernet. Note that the cable required for connecting the ExtIO (MOBOTIX USB cable or Ethernet installation cable) is not included in the delivered parts.
9/76 MOBOTIX ExtIO User Manual 1.2.2 Comparison ExtIO/CamIO Hinweis Supported MOBOTIX models Outdoor - weatherproof Power Supply Power input Integrated recharg. battery CamIO Hardware Features ExtIO Zur Nutzung aller Funktionen der ExtIO ist die Aktivierung über die ExtIO CamIO all models* M12, M22** IP65 IP65 PoE (Class 2)*** / USB 230 V AC / PoE typ. 1 W typ. 3.
10/76 The ExtIO is not included in the delivered parts On-Wall set (IP65, suitable for outdoor applications) MOBOTIX ExtIO User Manual 1.3 Accessories On-Wall Set (MX-D22-OPT-AP) The On-Wall set can reliably protect external cables to the ExtIO if the cables cannot be guided from below the housing but have to be led above the wall.
MOBOTIX ExtIO User Manual D22M USB Cable (MX-CBL-MU-MU-1 or MX-CBL-MU-MU-5) USB cables for connecting D22M IT and Secure models to an ExtIO. Cable length: 1 m/3 ft or 5 m/16 ft. M22M USB Cable (MX-CBL-U-MU-5) USB cables for connecting M22M IT and Secure models to an ExtIO. Cable length: 5 m/16 ft. M12 and D12 USB Cable (MX-CBL-HD-MU-5) USB cable for connecting M12 and D12 IT and Secure models to an ExtIO. Cable length: 5 m/16 ft. 11/76 You can use the ExtIO with all MOBOTIX IT and Secure models.
12/76 MOBOTIX ExtIO User Manual 2 MOUNTING THE EXTIO 2.1 Preparing the Installation Before mounting the MOBOTIX ExtIO, the following questions should be answered: 1) Where will the ExtIO be mounted? Mounting to a ceiling or wall; section 2.1.1. 2) How should I connect the ExtIO to the camera? Via LAN/network or via USB; section 2.1.2. 3) Which additional mounting options are available? On-wall mounting, in-ceiling mounting, wall mounting with Wall Mount or Pole Mount, section 2.1.
MOBOTIX ExtIO User Manual 13/76 The following sections contain a brief overview for all of these questions as well as references to the relevant sections in this manual, which contain more detailed information. For more information on the MOBOTIX ExtIO and the available accessories, please also refer to www.mobotix.com in the Products section. 2.1.1 Mounting to a Wall or Ceiling The ExtIO has been designed for mounting directly to a wall or ceiling.
14/76 MOBOTIX ExtIO User Manual 2.1.3 Mounting Options On-Wall set (IP65, suitable for outdoor applications) On-Wall set 10° (IP65, suitable for outdoor applications) On-Wall Set (MX-D22-OPT-AP) The On-Wall set can reliably protect external cables to the ExtIO if the cables cannot be guided from below the housing but have to be led above the wall. Note that the On-Wall set is also available with 10 degrees inclination.
MOBOTIX ExtIO User Manual 15/76 2.1.5 Directions for Mounting Once the type of installation, the camera connections and the mounting options have been decided upon, you should follow the directions listed below. This ensures that you only have to read the relevant sections of this chapter, which will speed up installing the ExtIO and connecting it to the MOBOTIX camera. Directions for Mounting Preparatory Tasks Sections ExtIO 2.1 2.2 2.
16/76 MOBOTIX ExtIO User Manual 2.2 ExtIO: Delivered Parts, Components and Dimensions 2.2.1 Delivered Parts and Components ExtIO (item 1.1) with mounting ring (item 1.2) 3 plugs for cable diameters 3 to 5 mm (item (item 1.7) 3 plugs for cable diameters 5 to 7 mm (item (item 1.8) 2 Fillister head screws (item 1.9) Outer shell (item 1.3) Mounting supplies for outer shell: 4 Allen screws M4x16 mm (item 1.4) 4 washers Ø 4.3 mm (item 1.5) Mounting supplies for mounting ring: 4 dowels 8 mm (item 1.
17/76 MOBOTIX ExtIO User Manual 2.2.2 Housing The housing of the MOBOTIX ExtIO is made of white fiber-reinforced plastic (PBTGF30, Polybutyleneterephtalate with 30% fiberglass). This material is used heavily in the automotive industry and is sturdy, resistant against high temperatures, environmental influences, chemicals, etc. The MOBOTIX ExtIO's main components are the ExtIO housing (includes the main board), the outer shell and the mounting ring.
18/76 MOBOTIX ExtIO User Manual 39 mm (1.5 in) 2.2.3 ExtIO: Dimensions Without Mounting Options dia. 160 mm (6.3 in) 2.2.4 Drilling Template Mounting Ring 100 mm (3.9 in) Find the drilling templates (scale 1:1) at the end of the manual as a fold-out 100 mm (3.9 in) Ø 5.5 mm (7/32 in) 17 mm Ø 68 mm / 2.7 in (cutting template for wall outlet) Note Find the folded drilling template at the end of the manual.
MOBOTIX ExtIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
20/76 MOBOTIX ExtIO User Manual 2.3 ExtIO Accessories: Delivered Parts, Components, Dimensions 2.3.1 On-Wall Set Housing (item 2.1) The ExtIO is not included in the delivery of the OnWall set! 4 Allen screws M4x35 mm (item 2.2) 4 washers dia. 4.3 mm (item 2.3) The On-Wall set can be used for the ExtIO and all Q22M and D22M models Item 2.1 2.2 2.3 Count 1 4 4 Part Name On-Wall set housing Stainless steel Allen screws M4x35 mm Stainless steel washers Ø 4.
MOBOTIX ExtIO User Manual 21/76 Drilling Template On-Wall Set Find the drilling templates (scale 1:1) at the end of the manual as a fold-out Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled or adjusted to the paper size when printing the PDF file. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
22/76 MOBOTIX ExtIO User Manual 2.3.2 In-Ceiling Set In-Ceiling mount (item 3.1) 5 clamps (item 3.4) The ExtIO is not included in the delivery of the InCeiling set! 5 winged cams (item 3.3) Wrench for In-Ceiling mount (item 3.5) Decoration ring (item 3.2) The In-Ceiling set can be used for the ExtIO and all Q22M and D22M models Item 3.1 3.2 3.3 3.4 3.
23/76 MOBOTIX ExtIO User Manual Cutting Template for In-Ceiling Set ∅ mm 150 n) 9i (5. Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled or adjusted to the paper size when printing the PDF file. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
24/76 MOBOTIX ExtIO User Manual 2.3.3 Wall Mount Bottom plate (item 5.8) 4 wood screws 6x50 mm (item 5.4) 8 Allen screws M4x16 mm (item 5.6) Wall mount (item 5.1) 4 washers Ø 6.4 mm (item 5.3) 4 dowels 8 mm (item 5.2) 8 washers Ø 4.3 mm (item 5.7) Wall sealing (item 5.5) Item 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Part Name Wall Mount Dowels 8 mm Stainless steel washers Ø 6.
MOBOTIX ExtIO User Manual 25/76 Drilling Template Wall Mount Find the drilling templates (scale 1:1) at the end of the manual as a fold-out Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled or adjusted to the paper size when printing the PDF file. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
26/76 MOBOTIX ExtIO User Manual 2.3.4 Pole Mount 4 Allen screws M8x30 mm (item 6.2) The Pole Mount can only be used in conjunction with the Wall Mount Pole Mount (item 6.1) 2 steel straps (item 6.5) 4 washers dia 9 mm (item 6.3) 4 lock nuts M8 mm (item 6.4) Count 1 4 4 4 2 Part Name Pole mount, stainless steel 3 mm, white powder-coated Stainless steel Allen screws M8x30 mm Stainless steel washers Ø 9 mm Stainless steel lock nuts M8 Stainless steel straps Height: 125 mm (4.
MOBOTIX ExtIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
28/76 MOBOTIX ExtIO User Manual © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX ExtIO User Manual © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
30/76 MOBOTIX ExtIO User Manual 2.4 Connecting the Terminal Connectors, Wiring 2.4.1 Overview: ExtIO Board and Connectors Terminal connectors for Ethernet cabling Terminal connector 1 (Signal inputs and outputs) Mini USB connector Terminal connectors – overview Terminal connector 2 (Line-In, Line-Out) ExtIO connection template © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
31/76 MOBOTIX ExtIO User Manual 2.4.2 ExtIO Terminal Connectors for the Ethernet Cabling Use Ethernet installation cable for connecting the cable to the Ethernet terminal connector. Make sure that you adhere to the allowed wire dimensions and to the applied Ethernet connection standard (usually EIA/ TIA-568B).
32/76 MOBOTIX ExtIO User Manual 2.4.3 ExtIO Terminal Connector 1 (Signal Inputs/Outputs) Make sure that you are adhering to the applicable regulations in your country regarding the allowed cables when connecting the wires to the terminal connector. Always observe the allowed wire dimensions (see table below). Terminal In2+ In2In1+ In1Out2+ Out2Out1+ Out1- AWG: American Wire Gauge (for measuring cable diameters) Part Name Remark Signal input 2 Ext. sensor 2, max. 50 V~/50 V= Signal input 1 Ext.
33/76 MOBOTIX ExtIO User Manual 2.4.4 ExtIO Terminal Connector 2 (Line-In/Line-Out) Make sure that you are adhering to the applicable regulations in your country regarding the allowed cables when connecting the wires to the terminal connector. Always observe the allowed wire dimensions (see table below). Terminal Line-Out+ Line-OutGND Line-In+ Line-In- Remark For connecting to the Line-In port of a computer or when using an external speaker with an amplifier, for example.
34/76 MOBOTIX ExtIO User Manual 2.5 Connecting a MOBOTIX USB Cable to the Camera 2.5.1 Overview When using the ExtIO via USB, you also need to order a model-specific MOBOTIX USB cable D22M USB cables: MX-EXTIO-D22-1 (1 m/3 ft) MX-EXTIO-D22-5 (5 m/16 ft) When using USB, you need to install the model-specific USB cable in the camera and then guide it through the camera, the SecureFlex mount or the mounting option.
35/76 MOBOTIX ExtIO User Manual 2.5.2 USB Connection to a D22M Camera 1) Remove one of the rubber plugs in the back of the D22M camera housing. This plug will not be used any more in the course of the installation process. USB cables for MOBOTIX D22M models: Remove rubber plug 2) Guide the MOBOTIX D22M USB cable with the angled Mini USB plug first from the opening in the back and under the lens mount.
36/76 MOBOTIX ExtIO User Manual 2.5.3 USB Connection to a M22M Camera USB cable (5 m/16 ft) for MOBOTIX M22M models: MX-CBL-U-MU-5 5 mm Allen wrench is included in the delivery of the M22M cameras Remove the cover 1) Unscrew the upper Allen screw in the foot of the mount, which holds the turn/tilt unit in place (5 mm Allen wrench). Remove the Allen screw, the washer and the hex nut from the mount. 2) Remove the cover.
37/76 MOBOTIX ExtIO User Manual Insert the cover 8) Guide the MOBOTIX M22M USB cable with the angled Mini USB plug first from below through the wall mount. 9) Insert the cover into the free opening of the wall mount's foot. Guide USB cable through here Insert the cover 10) Insert the turn/tilt unit of the camera into the horizontal opening of the mount (all the way to the stop). 11) Insert the hex nut into the corresponding hole and fasten the Allen screw with washer.
38/76 MOBOTIX ExtIO User Manual 2.5.4 USB Connection to a M12 Camera USB cable (5 m/16 ft) for MOBOTIX M12 and D12 models: MX-CBL-HD-MU-5 5 mm Allen wrench is included in the delivery of the M12 cameras Remove the cover 1) Unscrew the upper Allen screw in the foot of the mount, which holds the turn/tilt unit in place (5 mm Allen wrench). Remove the Allen screw, the washer and the hex nut from the mount. 2) Remove the cover.
39/76 MOBOTIX ExtIO User Manual 6) Guide the MOBOTIX M12 USB cable with the angled Mini USB plug first from below through the turn/tilt unit of the camera. 7) Insert the D Sub 15 HD plug of the MOBOTIX M12 USB cable into the D Sub 15 HD connector of the MOBOTIX camera. Guide USB cable through here Connect D Sub 15 HD plug 8) Reinstall the bottom cover of the mount. In the process, make sure that the camera's insect protection remains firmly in place.
40/76 MOBOTIX ExtIO User Manual 2.5.5 USB Connection to a D12 Camera USB cable (5 m/16 ft) for MOBOTIX D12 and M12 models: 1) Remove the two Allen screws of the cable cover (3 mm Allen wrench) and lift off the cable cover. MX-CBL-HD-MU-5 3 mm Allen wrench is included in the delivery of the D12 cameras Note: If the cable cover cannot be removed by hand, take a screwdriver to lift it out of its seat. Insert the screwdriver into the grooves shown below and gently lift the cable cover.
41/76 MOBOTIX ExtIO User Manual Install cable cover 5) Push the cable cover back into its seat and fasten the two Allen screws. When mounting the cable cover, take care to properly align the cover with the seal of the camera housing and the two cable guides. This will ensure that the camera remains weatherproof (IP65). Always mount the cable cover (IP65)! Maximum torque for all screws is 1 to 1.2 Nm (0.74 lbf ft) 6) Properly lead the cable through the cable guides at the outer rim of the housing.
42/76 MOBOTIX ExtIO User Manual 2.6 Connecting the Cables to the ExtIO 2.6.1 Connecting the Ethernet Cable to the ExtIO 1) Remove the outer shell from the ExtIO: Remove the outer shell (item 1.3) from the ExtIO. Use the supplied Allen wrench (item 1.14) for this purpose. Remove outer shell 2) Remove the mounting ring from the ExtIO: Remove the mounting ring from the ExtIO. Carefully bend the four black clamps of the mounting ring back, one after the other using a suitable tool.
43/76 MOBOTIX ExtIO User Manual 5) Guide the Ethernet cable through the ExtIO's back and close the opening with a plug: Remove the rubber plug at the center of the ExtIO's back. This plug will not be used any more in the course of the installation process. Guide the Ethernet cable through the opening into the interior. Make sure that about 17 cm/6.7 in of free cable remain in the camera. Carefully close off the opening in the ExtIO's back using the integrated plug of the Ethernet cable.
44/76 MOBOTIX ExtIO User Manual 2.6.2 Connecting the USB Cable to the ExtIO 1) Remove the outer shell from the ExtIO: Remove the outer shell (item 1.3) from the ExtIO. Use the supplied Allen wrench (item 1.14) for this purpose. Remove outer shell 2) Remove the mounting ring from the ExtIO: Remove the mounting ring from the ExtIO. Carefully bend the four black clamps of the mounting ring back using a suitable tool, one after the other.
45/76 MOBOTIX ExtIO User Manual 5) Close off ExtIO's back with USB plug: Carefully close off the opening in the ExtIO's back using the integrated plug of the Ethernet cable. Make sure that about 17 cm/6.7 in of free cable remain in the camera. All MOBOTIX USB cables have been prepared in such a way.
46/76 MOBOTIX ExtIO User Manual 2.6.3 Connecting Additional Components to the ExtIO 1) Remove the outer shell from the ExtIO: Remove the outer shell (item 1.3) from the ExtIO. Use the supplied Allen wrench (item 1.14) for this purpose. Remove outer shell 2) Remove the mounting ring from the ExtIO: Remove the mounting ring from the ExtIO. Carefully bend the four black clamps of the mounting ring back using a suitable tool, one after the other.
47/76 MOBOTIX ExtIO User Manual 5) Prepare the cable ties: Push one of the cable ties supplied with the ExtIO from the top downwards into the plastic clamp prepared for this purpose. Prepare the cable ties 6) Lock the cable in place with cable tie: Lock all wires of the cable in place using the cable tie and clip the superfluous end of the cable tie. Lock the cable in place with cable tie and clip cable tie 7) Lock the wires in the terminal connector: Shorten the individual wires to the required length.
48/76 MOBOTIX ExtIO User Manual 2.7 Mounting the ExtIO 2.7.1 Mounting the ExtIO Without Additional Mounting Options 1) Prepare the network or USB connection: The network cabling or USB cable need to enter the ExtIO from the back in the center of the housing. The cabling is perfectly protected by the mount and cannot be seen or damaged. Note Use a flush-mounted (empty) wall outlet for the cabling. The ExtIO itself cannot be mounted directly on top of protruding wall outlets.
49/76 MOBOTIX ExtIO User Manual 5) Attach the ExtIO to the mounting ring: Now press the ExtIO into the guides of the mounting ring. The tapered guides at the back of the ExtIO housing fit exactly into the openings of the mounting ring. Make sure that the ExtIO is properly oriented. The cover of the PIR sensor is supposed to be at the bottom, the speaker should be on top (see figures). Attach the ExtIO to mounting ring 6) Attach the outer shell: Attach the outer shell (item 1.3) to the ExtIO.
50/76 MOBOTIX ExtIO User Manual 2.8 Important Notes 2.8.1 Safety Regulations Caution It is imperative that all electrical wires have been disconnected from the mains power when working on or servicing the device! Also make sure to adhere to the applicable regulations for this kind of work! MOBOTIX will not assume any responsibility from faulty installation or inappropriate use! 2.8.2 Suitable Cables Only use cables, which have been approved for the pertinent type of installation.
MOBOTIX ExtIO User Manual 2.8.3 Safety Notes for Operating the MOBOTIX ExtIO When installing the wiring inside or outside of buildings, make sure you always adhere to the relevant regulations on wiring, fire prevention and protection against lightning.
52/76 MOBOTIX ExtIO User Manual 2.8.4 Weatherproofness, Temperature Range The housing of the MOBOTIX ExtIO is weatherproof (IP65, absolutely dustproof, resistant against water jets) and can be used at temperatures from -30 to +60°C (-22 to +140°F). 2.8.5 Cleaning Instructions The housing of the MOBOTIX ExtIO is made of fiber-reinforced PBT-30GF. This material is robust, maintenance-free and can be cleaned using a mild household detergent without solvents or abrasive particles. 2.8.
MOBOTIX ExtIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
54/76 MOBOTIX ExtIO User Manual 3 OPERATION OF THE EXTIO 3.1 Activating the ExtIO Once the ExtIO and the MOBOTIX camera have been properly installed, you can set up the camera for proper operation. When using USB, the camera directly supplies power via the model-specific USB cable. When using Ethernet, power is supplied via the Ethernet cable (PoE according to IEEE 802.3af).
MOBOTIX ExtIO User Manual 55/76 3.1.1 Activating the USB Operating Mode To activate the USB operating mode, open the Admin Menu > Manage Hardware Expansions dialog in the camera's browser interface. The ExtIO connected to the camera starts after you click the Connect button in front of the ExtIO (USB) entry. Once the green LED is on permanently, the ExtIO has successfully connected to the camera. The remaining configuration can now be performed in the camera software.
56/76 MOBOTIX ExtIO User Manual 3.1.2 Activating the Ethernet Operating Mode (NET) To activate the Ethernet operating mode, open the Admin Menu > Manage Hardware Expansions dialog in the camera's browser interface. Note that you need to enter the IP address of the ExtIO to establish a connection. Click on the Connect button in front of ExtIO (Ethernet Connection) to establish a connection between the camera and the ExtIO.
57/76 MOBOTIX ExtIO User Manual 3.1.3 Setting up the Network Parameters of the ExtIO for Ethernet Operation In order to integrate the ExtIO into the target network, you need to specify proper network parameters in the ExtIO (IP address, network mask, gateway). Please follow these steps to perform this task: 1) Connect the ExtIO and your computer via a PoE switch. PoE IEEE 802.3af! 10.1.0.11 1:1 Patch-Cable 1:1 Patch-Cable 10.0.0.
58/76 MOBOTIX ExtIO User Manual Note that these parameters are examples only. Make sure that you are using the correct parameters for your network. 6) Click on Set, then on Close to store the configuration permanently in the ExtIO's Flash memory. 7) Change the network parameters of your computer back to its original settings. You can now connect the ExtIO to the target network and use the camera software to activate it (see above).
59/76 MOBOTIX ExtIO User Manual 3.1.4 LED-Patterns of the ExtIO The MOBOTIX ExtIO uses its two muliti-color LEDs to display status information.They can light up permanently or blink in red, green and orange. The following table contains the most important LED patterns of the ExtIO.
60/76 MOBOTIX ExtIO User Manual 3.1.5 Starting the ExtIO Using the Factory Default Settings Under certain circumstances, you may have to reset the ExtIO to its factory default settings (e.g. if the IP address is unknown). Proceed as follows to start the device using its factory default settings: 1) If the ExtIO is powered on, disconnect the power supply by unplugging the USB and Ethernet cables. 2) Reconnect the power supply of the ExtIO by reconnecting the corresponding cable(s).
MOBOTIX ExtIO User Manual 3.1.6 Starting the ExtIO With an Automatic IP Address (DHCP) If required, the ExtIO can temporarily obtain an IP address from a DHCP server on your local network. Proceed as follows to start the ExtIO using DHCP: 1) If the ExtIO is powered on, disconnect the power supply by unplugging the USB and Ethernet cables. 2) Reconnect the power supply of the ExtIO by reconnecting the corresponding cable(s). 3) Wait until the left LED lights up orange.
62/76 MOBOTIX ExtIO User Manual 3.2 Sensors and Input/Output Interfaces of the ExtIO The ExtIO has the following sensors and input/output interfaces: • Status LEDs • Speaker and Microphone • Buttons (L – “Lights”, R – “Bell”) • PIR Motion Sensor • Signal Inputs/Outputs • Temperature sensor The following sections contain an overview over the additional configuration options if an ExtIO has been attached and connected. 3.2.
MOBOTIX ExtIO User Manual 3.2.3 Buttons Once the ExtIO has been attached and is connected, it will automatically activate its buttons and deactivate the buttons of the MOBOTIX camera. All events, actions or messages that are involving the buttons will not use the camera's buttons, but the buttons of the ExtIO. Open Setup Menu > Event Settings to set up the button events. 3.2.
64/76 MOBOTIX ExtIO User Manual 3.2.6 Temperature Sensor Once the ExtIO has been attached and is connected, it can use its temperature sensor in addition to the temperature sensor of the MOBOTIX camera. Open Setup Menu > Event Settings to set up the temperature sensor event. To see a table with the latest temperatures of both the ExtIO's and the camera's temperature sensor, open Admin Menu > Temperatures. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX ExtIO User Manual 3.3 Software Updates MOBOTIX provides free-of-charge software updates for the ExtIO on www.mobotix.com (Support > Software Downloads). These updates contain new features and – if required – bugfixes. This means that you can upgrade an early ExtIO (USB only) with Ethernet connectivity. To update the ExtIO software, load the new software into the MOBOTIX camera (Admin Menu > Update System Software). Note that you need a properly running and connected ExtIO for this to work.
66/76 MOBOTIX ExtIO User Manual 3.4 Configuration Example The following example of a door intercom system demonstrates one possible application and shows the steps for properly configuring a MOBOTIX D22M with an ExtIO using a USB connection. Action: call softphone Key 0: door opens Connection cable Door bell Legend Example: ExtIO as door intercom device with Video SIP and additional lights Action: open door Action: activate additional lights 3.4.
MOBOTIX ExtIO User Manual 67/76 In the meantime, the camera is automatically recording the video and audio stream on an SD card or Flash device in the MOBOTIX camera. This includes the sound from the ExtIO's microphone that is automatically transmitted to the MOBOTIX camera. 3.4.2 Overview of the Configuration Steps Configure the MOBOTIX camera (section 2.2.
68/76 MOBOTIX ExtIO User Manual You can find more detailed information on setting up recording on SD cards/ Flash devices in the MOBOTIX camera manuals and in section 8.3.6, Recording on Flash, USB and SD Storage Devices, in the Software Manual. • Activate VM event and set up video motion window (Setup Menu > Event Settings). • Activate recording for VM event (Setup Menu > Recording). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX ExtIO User Manual 3) Activate and configure the BR event • Activate BR event (Setup Menu > Event Settings) a) Switch additional lights (SO action) • Activate action profile (for VM and BR events) and configure SO action (Setup Menu > Actions). b) Record and configure voice message (SD message) • Set Audio Input to ExtIO (audio is transmitted directly from the ExtIO's microphone; Admin Menu > Loudspeaker and Microphone). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
70/76 MOBOTIX ExtIO User Manual • Record the voice message using the ExtIO's integrated microphone (optional: upload sound file to the camera; Admin Menu > Manage Audio Messages). • Activate message profile and configure SD message (for BR event) and select the recorded voice message (audio_welcome; Setup Menu > Messaging 2). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX ExtIO User Manual c) Configure VoIP phone call (CL message) For more information on setting up the SIP telephony features of MOBOTIX cameras, read chapter 9, Telephony Features in the Software Manual. • Configure the VoIP settings and activate VoIP (Admin Menu > VoIP Settings). • Set up a phone profile (Admin Menu > Phone Profiles). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
72/76 MOBOTIX ExtIO User Manual • Add CL message to messaging profile and select phone profile (Setup Menu > Messaging 2; SD message has already been configured). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX ExtIO User Manual 3.4.4 Configuring a Softphone • Configure the softphone and make sure that it is running on the computer. For more information on setting up a softphone for use with MOBOTIX cameras, read chapter 9, Telephony Features in the Software Manual. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
74/76 MOBOTIX ExtIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX ExtIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
76/76 MOBOTIX ExtIO User Manual Declaration of Conformity © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX – The HiRes Video Company To demonstrate our confidence in the quality of our products, MOBOTIX cameras were used to capture all the images that appear in this manual. Manufacturer Executive Board MOBOTIX AG Dr. Ralf Hinkel Kaiserstrasse D-67722 Langmeil Registration Office: Kaiserslautern Local Court Germany Registration Number: HRB 3724 Tel : +49 6302 9816-103 Tax Code: 44/676/0700/4 Fax: +49 6302 9816-190 Tax Office: Worms-Kirchheimbolanden, Germany http://www.mobotix.
ExtIO: Drilling Template Scale 1:1 1 00 mm/3.94 in 1 7 mm/ 0.67 in 1 00 mm/3.94 in ø5.5 mm/ 0.22 in Cutout for wall outlet Ø68 mm/2.7 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
ExtIO On-Wall Set: Drilling Template Scale 1:1 60 mm/2.36 in 1 00 mm/3.94 in ø5.8 mm/0.23 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
ExtIO In-Ceiling Set: Cutting Template Scale 1:1 i 5.9 / mm 0 ø1 5 n © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
71 .5 mm/2.82 in ExtIO Outdoor Wall Mount: Drilling Template Scale 1:1 50 mm/1 .97 in 3 mm/0.1 2 in ø7.5 mm/0.3 in 1 20 mm/4.72 in 86 mm/ 3.39 in 86 mm/3.39 in ø7.5 mm/0.3 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
X The HiRes Video Company MOBOTIX .com EN ExtIO User Manual ExtIO Opens New Horizons for Cameras Ethernet In2+ Terminal Block 1 IN2 In150 mA Out2+ Out2- LineOut+ LineOut- In2In1+ In1Out2+ Out1+ Out2Out1- Galv. separated, 50 V max.
