3 mm Beschnitt umlaufend 3 Megapixels 2048 x 1536 8x software zoom -22°F to +140°F Weatherproof -30°C to +60°C, IP65 no heating necessary D22M X Camera Manual Part 1 IEEE 802.
D22M Camera Manual Part 1 MOBOTIX Camera Data Enter the data of your camera here! Camera Model: Camera Name: Factory IP Address: . . . Current IP Address: . . . activated DHCP: deactivated Admin User Name: Admin Password: D22M Basic D22M Secure D22M with Vandalism Set Note: MOBOTIX offers inexpensive seminars that include a workshop and practical excercises: Basic Seminar 3 days, Advanced Seminar 2 days. For more information, see www.mobotix.
1/108 D22M Camera Manual Part 1 D22M CAMERA MANUAL PART 1 1 INTRODUCTION 6 1.1 MOBOTIX Cost Benefits 12 1.2 MOBOTIX Technical Advantages 13 1.3 MOBOTIX D22M Concept 14 1.4 Lens Options, Hardware and Software Features 20 1.5 Important Notes 1.5.1 Weatherproofness 1.5.2 Password for the Administration Menu 1.5.3 Irreversibly Deactivating the Microphone 1.5.4 Starting the Camera Using the Factory IP Address 1.5.5 Resetting the Camera to Factory Defaults 1.5.
2/108 D22M Camera Manual Part 1 2.4 2.4.1 2.4.2 2.4.3 2.4.4 2.4.5 Camera Accessories: Delivered Parts, Components and Dimensions D22M On-Wall Set D22M In-Ceiling Set D22M Vandalism Set D22M Wall Mount D22M Pole Mount 42 42 44 46 48 50 2.5 2.5.1 2.5.2 2.5.3 2.5.4 Mounting the Camera D22M-IT/Secure D22M-Basic Finishing the Mounting Process Notes on Mounting the Camera to a Wall Without the Wall Mount 52 52 53 56 58 2.6 Mounting the D22M to a Ceiling Using the On-Wall Set 60 2.
D22M Camera Manual Part 1 3/108 APPENDIX: IP65/IP54 CERTIFICATE, DECLARATION OF CONFORMITY DRILLING TEMPLATES (SCALE 1:1) Note Chapters 4 and above are part of the Camera Software Manual (Software Manual in short). The main headings are listed below to give you an overview of the Software Manual contents. SOFTWARE MANUAL PART 2 4 CAMERA USER INTERFACE 4.1 The First Image in the Browser 4.2 The First Image in MxControlCenter 4.3 The Live Screen in the Browser 4.
4/108 D22M Camera Manual Part 1 6 SOFTWARE UPDATES 6.1 Overview 6.2 Preparatory Steps 6.3 Updating the Camera Software 6.4 Update Checklist 7 EVENTS, ACTIONS AND MESSAGES 7.1 Overview 7.2 Functional Overview 7.3 General Procedure 7.4 Screen Display of Event Settings in Live Image 7.5 Arming 7.6 Events 7.7 Actions and Messaging, Action and Messaging Profiles 7.8 Working with Profiles 7.9 Time Tasks 8 RECORDING 8.1 Overview 8.2 Recording Modes 8.
D22M Camera Manual Part 1 10 5/108 MOBOTIX CAMERAS ON THE WEB 10.1 Overview 10.2 Indirectly Accessing MOBOTIX Cameras via the Web 10.3 Directly Accessing MOBOTIX Cameras via the Web 10.4 Configuring the Router 10.5 DynDNS 11 SOFTWARE INTERFACES 11.1 Overview 11.2 Accessing the Camera's Live Image and the Event Images 11.3 Accessing the Camera's Live Image Using the Second Image Channel 11.4 Video Streaming 11.5 The HTTP API 12 TROUBLESHOOTING 12.1 Overview 12.2 Troubleshooting Checklist 12.
6/108 D22M Camera Manual Part 1 1 High resolution: QXGA format with 2048x1536! 30 frames per second in VGA format! INTRODUCTION The D22M cameras are powerful yet compact MOBOTIX network cameras that are capable of creating high-resolution live video streams (QXGA format: 2048x1536 pixels) with high image rates. When showing VGA video (640x480), the camera can deliver up to 30 fps. Even Megapixel video (1280x960) will still generate up to 10 fps.
7/108 D22M Camera Manual Part 1 evaluating the alarm video clips and provides alerting features (including audio). While MxControlCenter has been providing virtual PTZ features for quite a while, these features are now available directly in the MOBOTIX camera. This means that you can continuously zoom into or out of the live image using either the mouse wheel or a joystick.
8/108 D22M Camera Manual Part 1 D22M-Basic The D22M-Basic, with a diameter of only 12.9 cm (5 in) and a height of only 8.5 cm (3.3 in) is the most compact and most discrete MOBOTIX camera. The camera is weatherproof (IP54) and thus suited for outdoor use. ø 129 mm/5.1 in Note Die D22M-Basic ist die richtige Wahl für Webcam-Anwendungen und einfache Überwachungsaufgaben.
D22M Camera Manual Part 1 • 9/108 Vandalism Set: The Vandalism Set provides added protection for D22M cameras. The set consists of a robust camera ring made of stainless steel and a reinforced dome made from 3 mm thick polycarbonate. A camera with vandalism set is perfectly suited for applications in demanding environments (such as prisons, social hot-spots, train stations, etc.).
10/108 D22M Camera Manual Part 1 • In-Ceiling Set: The In-Ceiling Set allows mounting the D22M in fake ceilings, for example. This type of installation provides optimum protection for the camera and reduces the visible profile to a minimum since only the dome is visible. • Wall Mount: The Wall Mount is the ideal solution for mounting the D22M to walls for indoor and outdoor applications. The camera is absolutely dustproof and resistant against water jets (IP65).
D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
12/108 D22M Camera Manual Part 1 1.
D22M Camera Manual Part 1 1.
14/108 D22M Camera Manual Part 1 1.3 MOBOTIX D22M Concept High-resolution live video with up to 30 frames/s The MOBOTIX cameras deliver smooth live video display in VGA format (640x480 pixels) with synchronous live audio, yet it keeps the network load to a minimum. Live video display now matches the performance of analog video systems.
15/108 D22M Camera Manual Part 1 Recording on Flash, USB and SD storage media The current MOBOTIX cameras support direct storage on the integrated Flash storage media, internal SD cards and external USB media. Int.
16/108 D22M Camera Manual Part 1 Remote alerting In case of an alarm, MOBOTIX cameras automatically pop up windows or activate other functions at a remote security control center. The cameras can use network/ wireless, GSM/GPRS/UMTS (3G) or Internet connections for this purpose.
D22M Camera Manual Part 1 Notes: More Features © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
18/108 D22M Camera Manual Part 1 • Live images of up to 2048x1536 pixels resolution via network, ISDN, GSM, GPRS, UMTS, wireless with up to 30 fps (at VGA resolution 640x480), also adapted for PDAs. • Continuous digital zoom (up to 8x zoom) and integrated panning (clicking with the mouse near the borders of the image will move the visible image area within the full image).
D22M Camera Manual Part 1 • Remote signaling for master/slave cameras, with the master camera controlling the arming status of the slave cameras. This allows arming, for example, of all slave cameras by using a key switch that is connected to the master camera. • Transfer profiles for comfortably controlling transmissions via FTP, e-mail, phone calls and network messages.
20/108 D22M Camera Manual Part 1 1.4 Lens Options, Hardware and Software Features MOBOTIX currently offers five standard lenses with M14 thread from Super WideAngle L22 with 22 mm focal length up to the tele lens L135 with 135 mm focal length (equiv. to 35 mm camera). Since MOBOTIX cameras are backlight-proof, they do not require a mechanical auto iris. This makes all MOBOTIX lenses extremely robust and maintenance-free.
21/108 D22M Camera Manual Part 1 Lens Table Order name L22 L32* L43 L65* L135 35 mm equivalent 22 mm 32 mm 43 mm 65 mm 135 mm Focal length 4 mm 6 mm 8 mm 12 mm 25 mm F-Number 2.0 2.0 2.0 2.0 2.5 Image angle horizontally 90° 60° 45° 31° 15° Image angle vertically 67° 45° 34° 23° 11° Distance 1 m m m m m m • Image width 2,0 1.1 0.8 0.5 0.3 • Image height 1.3 0.8 0.6 0.4 0.2 Distance 5 m m m m m m • Image width 10.0 5.7 4.1 2.7 1.
D22M-IT MX-D22M-IT-D22 D22M-Sec MX-D22M-Sec-D22 D22M-Sec-Night MX-D22M-Sec-Night-N22 D22M Camera Manual Part 1 D22M-Basic MX-D22Mi-Basic-D22 22/108 IP54 IP65 IP65 IP65 Hardware Features D22M Requires special adapter cable for USB Outdoor weatherpr.
23/108 Basic Models Web Models IT Models Secure Models D22M Camera Manual Part 1 - X X X X/X X/X X/X X/X Custom exposure windows X X X X Video Motion detection X X X X Time and event control (FTP, email, logos) X X X X Custom time tables/holidays - X X X Web functionality (FTP, email) X X X X Quad/MultiView in browser X X X X Recording/Playback in browser X X X X Logo generator, animated - X X X Single image recording (pre-/post-alarm images) 3 3 10 5
24/108 D22M Camera Manual Part 1 1.5 Important Notes 1.5.1 Weatherproofness The MOBOTIX D22M IT and Secure models reach protection class IP65 (absolutely dustproof, resistant against water jets) and are an excellent choice for outdoor applications when used with the D22M Outdoor wall mount. The Basic model of the MOBOTIX D22M reaches protection class IP54. 1.5.
D22M Camera Manual Part 1 25/108 1.5.4 Starting the Camera Using the Factory IP Address If the camera's IP address is not known, you can start the camera with its factory IP address. Section 3.6, Starting the Camera Using the Factory IP Address, describes this procedure in more detail. 1.5.5 Resetting the Camera to Factory Defaults All settings of the MOBOTIX camera can be reset permanently to the factory default settings.
26/108 D22M Camera Manual Part 1 1.5.8 Deactivating the Automatic Daily Reboot of the Camera Deactivating the camera reboot In its default configuration, the MOBOTIX camera automatically reboots every morning at 3:36 am. The reason for this is that external influences (e.g. radiation in high locations) can lead to camera malfunctions. The automatic reboot will refresh the camera's memory and will ensure proper operation without requiring any interaction on the part of the user.
D22M Camera Manual Part 1 27/108 1.5.13 Additional Information For more information on this topic, see the News and Functional Overview pages in the online help of the camera's browser interface. Click on the yellow icon in the top right corner to open the camera's online help. To get complete information on the camera status and its current configuration, open the Camera Status dialog. Click on the yellow icon in the top right corner to open the corresponding camera dialog.
28/108 D22M Camera Manual Part 1 2 MOUNTING THE CAMERA 2.1 Preparing the Installation Before mounting the MOBOTIX D22M, the following questions should be solved: 1) Where will the camera be mounted? Mounting the camera to a ceiling or wall, section 2.1.1 2) Which other mounting options are available? On-wall mounting, vandalism protection, wall mounting with Wall Mount, pole mounting with Pole Mount, in-ceiling mounting, section 2.1.
D22M Camera Manual Part 1 29/108 2.1.2 Additional Mounting Options for IT/Secure Models On-Wall Mounting (D22M-OPT-AP) The On-Wall set can reliably protect external cables if the cables cannot be guided from below the housing but have to be led above the wall. In addition, the OnWall mount provides ample space for extra modules. Q22M/D22M On-Wall Set (IP65, also for Outdoor applications) In-Ceiling Mounting (D22M-OPT-TC) The In-Ceiling Set allows mounting the camera in fake ceilings, for example.
30/108 D22M Camera Manual Part 1 2.1.3 Network Connection and Power Supply, UPS Power-over-Ethernet (MxPoE) Power is supplied to all D22M models via the network cabling (MxPoE, Powerover-Ethernet). For smaller installations, the universal power supply (MX-SNT-E/U/ GB/J/AUS01-30-RJ) with the MOBOTIX Network Power Adapter MX-NPA-3-RJ is sufficient.
D22M Camera Manual Part 1 31/108 Using Uninterruptible Power Supplies (UPS) In order to maintain a continuous power supply even when utility power fails, you should install an uninterruptible power supply (UPS). These devices also provide full protection against electrical surges and voltage fluctuations and thus enhance the reliability of the system as a whole. When using a more powerful 19" rack-mounted USP, you can also protect all other network components (e.g. switches, routers, PoE switches, etc.).
32/108 D22M Camera Manual Part 1 2.1.5 Directions for Mounting Once the type of installation, the camera connections and the method of power supply have been decided upon, you should follow the directions listed below. This will ensure that you will only have to read the relevant sections of this chapter, which will speed up mounting the D22M.
D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
34/108 D22M Camera Manual Part 1 2.2 D22M-IT/Secure: Delivered Parts, Components and Dimensions 2.2.1 Delivered Parts and Components D22M-IT/Secure Camera housing (item 1) with mounting ring (item 1.9) 4 wood screws 4.5x60 mm (item 1.12) 4 dowels 8 mm (item 1.10) 4 washers ø5.3 mm (item 1.11) Lens (item 1.2) Lock ring (item 1.3) Make sure to check the delivered parts! Outer shell (item 1.8) ∅ 160 mm/6.3 in Dome (item 1.4) 4 Allen screws M4x16 mm (item 1.14) 4 washers ø4.3 mm (item 1.
D22M Camera Manual Part 1 35/104 /108 2.2.2 Camera Housing and Connectors D22M-IT/Secure The MOBOTIX D22M-IT/Secure consists of the camera housing (motherboard, lens, dome), the outer shell and the mounting ring. Connectors • • • • NET (Ethernet network/power supply) External audio support (Microphone/Speaker) Mini USB/MOBOTIX bus (for future extensions) Slot for SD card SD cards are supported from software version 3.4.2 Outer shell Dome Lens unit Connectors NET (back) Ext.
D22M Camera Manual Part 1 2.2.3 Dimensions of the D22M-IT/Secure Freely positionable camera module 85 mm/3.3 in 36/108 ø 160 mm/6.3 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
37/108 D22M Camera Manual Part 1 2.2.4 Drilling Template for the D22M-IT/Secure Mounting Ring 100 mm/3.9 in 100 mm/3.9 in 5.5 mm/0.22 in n 6i /5. m m .4 141 Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates.
38/108 D22M Camera Manual Part 1 2.3 D22M-Basic: Delivered Parts, Components and Dimensions 2.3.1 Delivered Parts and Components D22M-Basic Camera housing (item 2.1) 4 wood screws 4.5x60 mm (item 2.12) 4 dowels 8 mm (item 2.10) 4 washers ø5.3 mm (item 2.11) Lens (item 2.2) Lock ring (item 2.3) Make sure to check the delivered parts! Toothed wrench (item 2.7) Dome (item 2.4) 4 Allen screws M4x16 mm (item 2.14) 4 washers ø4.3 mm (item 2.15) ∅ 129 mm/5.1 in Allen wrench (item 2.6) Torx wrench (item 2.
D22M Camera Manual Part 1 39/108 2.3.2 Camera Housing and Connectors D22M-Basic The MOBOTIX D22M-Basic consists of the camera housing with the motherboard, the lens and the dome. Connectors • • NET (Ethernet network/power supply) For external loudspeaker (Basic models only provide DHCP announcement) The MOBOTIX bus (MxB) and the SD card slot can only be used in D22M-IT and Secure models using a future update of the camera software Dome Lens unit Connectors NET (back) Ext.
D22M Camera Manual Part 1 2.3.3 Dimensions of the D22M-Basic Freely positionable camera module 85 mm/3.3 in 40/108 ø 129 mm/5.1 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
41/108 D22M Camera Manual Part 1 2.3.4 Drilling Template for the D22M-Basic 100 mm/3.9 in 78 mm/3.1 in Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
42/108 D22M Camera Manual Part 1 2.4 Camera Accessories: Delivered Parts, Components and Dimensions 2.4.1 D22M On-Wall Set Mounting set (item 3.1) The D22M is not included in the delivery of the OnWall Set! ∅ 165 mm/6.5 in 4 Allen screws M4x35 mm (item 3.2) 4 washers ø4.3 mm (item 3.3) Item 3.1 3.2 3.3 Count 1 4 4 Part Name Mounting set for D22M Stainless steel Allen screws M4x35 mm Stainless steel washers Ø 4.3 mm © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
43/108 D22M Camera Manual Part 1 Drilling Template for the D22M On-Wall Set 60 mm/2.4 in ø5.8 mm/2.3 in 100 mm/3.9 in Find the drilling templates (scale 1:1) at the end of the manual as a fold-out Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file.
44/108 D22M Camera Manual Part 1 2.4.2 D22M In-Ceiling Set In-Ceiling mount (item 4.1) 5 clamps (item 4.4) The D22M is not included in the delivery of the InCeiling Set! ∅ 150 mm/5.9 in diameter Wrench for In-Ceiling mount (item 4.5) 5 winged cams (item 4.3) Decoration ring (item 4.2) Item 4.1 4.2 4.3 4.4 4.5 Count 1 1 5 5 2 Part Name In-Ceiling Set for D22M Decoration ring Winged cam Clamps Wrench for In-Ceiling mount © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
45/108 D22M Camera Manual Part 1 Drilling Template for the D22M In-Ceiling Set ∅ n 9i /5. m m 150 ter me a i d Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
46/108 D22M Camera Manual Part 1 2.4.3 D22M Vandalism Set 4 security screws (item 5.3) Available colors of the D22M Vandalism Set: 1 Vandalism ring (item 5.1) - Matt - Polished - Powder-coated (black, white, silver-gray) ∅ 160mm/6.3 in 1 reinforced dome (item 5.5) The D22M is not included in the delivery of the InCeiling Set! 4 spacers (item 5.2) 1 two-hole driver bit (item 5.4) Item 5.1 5.2 5.3 5.4 5.
47/108 D22M Camera Manual Part 1 Available Colors of the D22M Vandalism Ring The D22M Vandalism Set provides added protection for D22M cameras. The set consists of a robust camera ring made of stainless steel and a reinforced dome made of 3 mm thick polycarbonate. A camera equipped with the Vandalism Set is perfectly suited for applications in demanding environments (such as prions, social hot-spots, train stations, etc.).
D22M Camera Manual Part 1 2.4.4 D22M Wall Mount Bottom plate (item 6.8) 4 wood screws 6x50 mm (item 6.4) 8 Allen screws M4x16 mm (item 6.6) Wall mount (item 6.1) 4 washers ø6.4 mm (item 6.3) 4 dowels 8 mm (item 6.2) 8 washers Ø 4.3 mm (item 6.7) Wall sealing (item 6.5) Item 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 Count 1 4 4 4 1 8 8 1 Part Name Wall Mount Dowels 8 mm Stainless steel washers Ø 6.
49/108 D22M Camera Manual Part 1 15 mm/ 0.59 in 75 mm/2.95 in Drilling Template for the D22M Wall Mount 160 mm/6.3 in Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
50/108 D22M Camera Manual Part 1 2.4.5 D22M Pole Mount 4 Allen screws M8x30 mm (item 7.2) The Pole Mount can only be used in conjunction with the D22M Wall Mount Pole mount (item 7.1) 2 steel straps (item 7.5) 4 washers Ø 9 mm (item 7.3) 4 lock nuts M8 mm (item 7.
D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
52/108 D22M Camera Manual Part 1 2.5 Mounting the Camera 2.5.1 D22M-IT/Secure Before mounting the MOBOTIX D22M-IT/Secure, you need to prepare the network connection and drill the holes for the fixtures: • Network connection: The network cabling is supplied through the ceiling directly above the camera. The cabling is perfectly protected and cannot be seen or damaged.
D22M Camera Manual Part 1 53/108 2.5.2 D22M-Basic Before mounting the MOBOTIX D22M-Basic, you need to prepare the network connection and drill the holes for the fixtures: • Network connection: The network cabling is supplied through the ceiling directly above the camera. The cabling is perfectly protected and cannot be seen or damaged. When preparing the installation, you should make sure that the cable runs at least 15 cm (6 in) within the camera housing (excluding the connector itself).
54/108 D22M Camera Manual Part 1 • Release the internal part of the camera by turning the ring inside in counter-clockwise direction using the supplied toothed wrench. While doing so, hold the camera at the lens unit to prevent it from turning. • Disengage the internal part of the camera with the lens unit from the base of the housing. • Position the base of the camera housing over the drilled holes and the prepared cable exit in the ceiling.
D22M Camera Manual Part 1 • Insert the internal part of the camera with the lens unit into the mounted base of the housing and secure it by turning the two blue clamps in clockwise direction using the supplied toothed wrench or a screwdriver. This will prevent the internal part of the camera to accidentally fall out of the base before it has been secured.
56/108 D22M Camera Manual Part 1 2.5.3 Finishing the Mounting Process Establishing a Connection to the Camera • Establish a connection to the camera as described in section 3.4, Establishing a Connection to the Camera. Adjusting the Lens, Visual Check Make sure that you see the live image of the camera on the monitor of your computer or laptop. Now adjust the lens until you see the desired image area on your monitor. • Remove the camera dome.
D22M Camera Manual Part 1 • • Once you are seeing the desired image area, tighten the Allen screws at the sides of the lens unit (in clockwise direction) and the toothed ring inside the camera. Do not use excessive force when doing so to avoid damaging the camera. Release the lens' lock ring and adjust the image focus by turning the lens in its holder. Check the image on the computer monitor. Make sure that you tighten the lock ring again once you are finished.
58/108 D22M Camera Manual Part 1 2.5.4 Notes on Mounting the Camera to a Wall Without the Wall Mount The MOBOTIX D22M has been designed to be mounted to either ceilings or to a wall, when using the Wall Mount. It is also possible to mount the D22M directly to a wall (without using the Wall Mount), but doing so will result in reduced flexibility for positioning the lens. The following section contains some hints on these restrictions and tips for mounting the camera to a wall.
59/108 D22M Camera Manual Part 1 Tilt the camera to see a larger area of the room (camera mounted 1 m/3 ft to the left of the center) 1 m/3 ft 1 m/3 ft 0° 1 m/3 ft 10° 30° This effect also appears when mounting a D22M at the center of a wall and you are turning the base of the camera. This will also allow to capture a larger area of the room with the camera, but the image is again tilted.
60/108 D22M Camera Manual Part 1 2.6 Mounting the D22M to a Ceiling Using the On-Wall Set Before mounting the MOBOTIX D22M-IT/Secure to an indoor or outdoor location using the On-Wall Set, you need to prepare the network connection and drill the holes for the fixtures: • Network connection: You can use any one of the four openings in the OnWall mount to guide the cabling into the camera.
D22M Camera Manual Part 1 • Disengage the mounting ring from the housing of the D22M-IT/Secure. This ring is not required when mounting the camera to the On-Wall Set. • Connect the network cable to the network cable of the camera using a patch cable connector. Make sure to leave enough unused cable within the housing. This will ensure that you can turn the lens unit freely later on. Cable that is too long can be stored easily within the On-Wall mount.
62/108 D22M Camera Manual Part 1 2.7 Mounting the D22M to a Ceiling Using the In-Ceiling Set Before mounting the MOBOTIX D22M-IT/Secure to an indoor location using the InCeiling Set, you need to prepare the network connection and drill the hole for the camera: • Find the drilling template at the end of the manual Network connection: The network cabling is supplied through the ceiling directly above the camera.
D22M Camera Manual Part 1 • 63/108 Insert the In-Ceiling Set with the camera into the hole in the ceiling. Tightening the integrated mounting screws will automatically secure the In-Ceiling mount to the ceiling. The winged cams automatically secure the InCeiling Set in the ceiling when tightening the screws (see detail pictures) Winged cam • Finally, press the decoration ring onto the mount and lock in place by turning it in clockwise direction.
64/108 D22M Camera Manual Part 1 2.8 Mounting the D22M Vandalism Set In order to install the Vandalism Set, replace the regular outer shell and the Allen screws with the stainless steel shell, the security screws and the four spacers of the Vandalism Set. Likewise, replace the dome of the D22M-IT/Secure with the reinforced dome of the Vandalism Set. • Remove the outer shell. Remove all four Allen screws using the supplied Allen wrench. Take off the outer shell. • Remove the camera dome.
D22M Camera Manual Part 1 • Mount the stainless steel shell of the Vandalism Set. Do not forget to insert the four spacers of the Vandalism Set into their seats in the camera housing! • Mount the supplied stainless steel shell with the security screws and use the supplied two-hole driver bit to firmly tighten the screws. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
66/108 D22M Camera Manual Part 1 2.9 Mounting the D22M to a Wall Using the Wall Mount Before mounting the MOBOTIX D22M-IT/Secure with the Wall Mount you need to prepare the network connection and drill the holes for the fixtures: • Network connection: The network cabling is supplied through the opening in the back of the wall mount. The cabling is perfectly protected by the mount and cannot be seen or damaged.
D22M Camera Manual Part 1 • Connect the network cable to the network cable of the camera using a patch cable connector (or plug the cable directly into the RJ45 wall outlet). Make sure to leave enough unused cable within the housing. This will ensure that you can turn the lens unit freely later on. Cable that is too long can be stored easily within the housing. • Now press the D22M into the guides of the wall mount.
68/108 D22M Camera Manual Part 1 2.10 Notes 2.10.1 Cleaning Instructions Cleaning the Dome • • • • In order to protect the dome from being scratched and from getting dirty, only handle the dome using a soft cotton cloth or the protective plastic of the camera's shipping box. You should clean the dome at regular intervals. Always use a lint-free cotton cloth for this purpose. If the dirt is more persistent, add a mild alcohol-free detergent without abrasive particles.
D22M Camera Manual Part 1 • Avoid induction: When running data cables parallel to existing regular power lines or high-voltage wires, make sure you observe the minimum distances to the power cables. Fire Prevention When installing the power lines to the camera, make sure you always adhere to the relevant regulations on wiring and fire prevention at the site of the installation.
70/108 D22M Camera Manual Part 1 2.11 Camera Accessories Power supply (MX-SNT-E/U/GB/J/AUS01-30-RJ) The MOBOTIX power supply is required if you do not use a Network Power Rack or Network Power Box, or a PoE-compatible switch or router. Network Power Adapter (MX-NPA-3-RJ) The Network Power Adapter allows injecting the power supply for the MOBOTIX camera into the network cable. It thus allows using the network cable for connecting to the camera and for remotely supplying power (up to 100 m (300 ft)).
D22M Camera Manual Part 1 71/108 On-Wall Set (MX-D22-OPT-AP) The On-Wall set can reliably protect external cables if the cables cannot be guided from below the housing but have to be led above the wall for technical or legal reasons. In addition, the On-Wall mount provides ample space for extra modules. ø 165 mm x 37 mm /6.5 x 1.
72/108 D22M Camera Manual Part 1 Pole Mount (MX-D22-OPT-MH) Pole mount made of 3 mm stainless steel The Pole Mount can only be used in conjunction with the Wall Mount. The supplied stainless steel straps allow attaching the mount to poles with diameters between 60 and 180 mm (2.4 to 7.1 in). The Pole Mount is made from 3 mm white powdercoated stainless steel and is just as robust and maintenance-free as the outdoor Wall Mount. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
74/104 D22M Camera Manual Part 1 3 OPERATING THE CAMERA 3.1 General Procedure The MOBOTIX camera does not require any software installation; all you need is your preferred browser with JavaScript support to operate the camera. Thus, the MOBOTIX camera is supported by all common operating systems (such as Windows, Macintosh and Linux, ...). 3.1.
D22M Camera Manual Part 1 75/104 Note After first booting a new MOBOTIX camera or after resetting to factory defaults, accessing the Administration menu (Admin Menu button) will automatically start the Quick Installation wizard. This is where you configure the most important camera parameters in a step-by-step manner. If you have completed the Quick Installation wizard at least once, the standard Administration menu will open when you click on the Admin Menu button.
76/104 D22M Camera Manual Part 1 3.2 Overview of the Configuration Settings Using the Quick Installation wizard After booting the camera for the first time or after resetting it to factory defaults, any access to the administration menu (Admin Menu button) will start the Quick Installation. This wizard will guide you through the most important settings of the camera (configuration of the network interface, image control, etc.) and can also be used to reset the camera to its factory settings.
D22M Camera Manual Part 1 77/104 All changes are temporary All changes to the configuration are only temporary and can thus be tested easily. Restoring the previous configuration settings can be achieved using the Restore button in most dialogs or by running Admin Menu > Restore last stored configuration from flash (see also section 5.9, Managing Settings, in the Software Manual). Once you have finished configuring the camera, you should always store the settings in the camera's permanent memory.
78/104 D22M Camera Manual Part 1 3.3 Connecting the Camera, Power Supply 3.3.
79/104 D22M Camera Manual Part 1 3.3.2 Camera Startup Sequence As soon as the power supply is established, the camera's LEDs will provide information on the startup sequence of the camera. • • • Booting: Immediately after connecting the power supply, the red LED lights up, blinks for two seconds, then stays on permanently. The camera's boot loader checks the hardware, unpacks and starts the operating system.
80/104 MOBOTIX power supply and Network Power Adapter required D22M Camera Manual Part 1 3.3.3 Power Supply (MxPoE) Using a Switch • • • Connect the factory pre-installed cable of the camera to the Camera connector of the Network Power Adapter. Connect the LAN/Power connector of the Network Power Adapter to an Ethernet connector of the switch/router or the Ethernet wall outlet. Plug the RJ45 connector of the external power unit into the PC/Power connector of the Network Power Adapter. 3.3.
D22M Camera Manual Part 1 3.3.5 Power Supply (MxPoE) Using a Network Power Rack or Network Power Box • • Connect the factory pre-installed cable of the camera to the CAM connector of the Network Power Rack (MX-NPR-8/20) or the Network Power Box (MX-NPR-4). Connect the LAN connector of the Network Power Rack to an Ethernet connector of the switch/router.
82/104 D22M Camera Manual Part 1 3.4 The First Image from the Camera Once the Ethernet connection has been established, you have the following possibilities to see the first image of the camera: Working with the webbased user interface only requires a web browser with activated JavaScript! • • Automatic camera search and configuration using MxControlCenter (free Windows client for MOBOTIX cameras; section 3.4.6, The First Image in MxControlCenter) Manual configuration (section 3.4.
D22M Camera Manual Part 1 Make sure that no other network device uses the camera's IP address: • Open a command shell (Windows) or a terminal (Linux/UNIX/OS X) and enter the following command: ping If you receive an answer from another network device although the camera is not connected, you will have to remove that device until you have reset the MOBOTIX camera to a free IP address. We recommend using the Quick Installation wizard for assigning a new IP address to the camera.
84/104 D22M Camera Manual Part 1 3.4.2 The First Image in the Browser Camera access: http://10.1.0.99 (example) The factory IP address is printed on the sticker on the camera Now that you have successfully started the camera for the first time, you can access the camera using your preferred browser to see the live video stream and the user interface. Internet Explorer, Mozilla, Firefox, Safari, Camino or any other graphical browser with activated JavaScript is suitable.
D22M Camera Manual Part 1 85/104 Additional Information For more information on this topic, see the News and Functional Overview pages in the online help of the camera's browser interface. Click on the yellow icon in the top right corner to open the camera's online help. In order to obtain more information on the camera and its current configuration, icon in the top right open the Camera Status dialog by clicking on the yellow corner of the camera's browser interface.
86/104 D22M Camera Manual Part 1 3.4.3 Camera Screens in the Browser All camera windows: Click on to open the online help pages for the camera screens Live screen: http:/// control/userimage.
D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
88/104 D22M Camera Manual Part 1 3.4.4 Access Using Zeroconf/Bonjour Bonjour is the implementation of this service in Apple Mac OS X from version 10.4; in Mac OS X 10.2 and 10.3, this service is called Rendezvous. Bonjour is available free of charge for Windows computers from the Apple web site www.apple.com/bonjour. For Linux and UNIX, Avahi provides the corresponding functionality. For further information on Bonjour and Zeroconf, please consult www.apple.
D22M Camera Manual Part 1 89/104 Prerequisites for Using Zeroconf/Bonjour MOBOTIX camera: • • Zeroconf has to be activated (Admin Menu > Ethernet Interface). This is the factory default for MOBOTIX cameras from software version 3.0.3.37. The camera needs to be in the same physical subnet as the computer (Admin Menu > Ethernet Interface). Operating system: • Microsoft Windows (2000, XP, 2003, Vista): Bonjour for Windows has to be installed (www.apple.com/bonjour).
90/104 D22M Camera Manual Part 1 • Macintosh OS X (10.2 or higher): Bonjour is included in the Apple operating system. There is no other configuration required. The list of Bonjour-enabled network devices is displayed in Safari after clicking on the Bonjour button. • Linux: Zeroconf is included in KDE from version 3.4 and in Gnome from version 2.8. The list of Bonjour-enabled network devices is displayed after entering zeroconf:/ in the Konqueror address bar.
D22M Camera Manual Part 1 91/104 Note If a proxy server is used in your network, you may get an error message when trying to access a MOBOTIX camera in the web browser. Make sure that the list of proxy exceptions in your browser contains the following entry: *.local *.local. .local. (Windows) (Mac OS X) (Linux) To find the proxy exceptions in Internet Explorer for Windows, open Tools > Connections > LAN Settings > Settings > Proxy server > Advanced and add the entry in the Exceptions text field.
92/104 D22M Camera Manual Part 1 3.4.5 Browser Settings Current browsers with activated JavaScript (Internet Explorer, Netscape, Mozilla, Firefox, Safari, Konqueror, Opera, Camino, etc.) can show the camera's live images without changing the default settings. Text-based browsers (e.g. lynx) cannot display the user interface and are not suitable for operating the camera.
D22M Camera Manual Part 1 • • Security Settings: Restrictive browser security settings may complicate or even prevent using the browser-based user interface of the MOBOTIX camera. Make sure that JavaScript or Active Scripting (whichever is appropriate) are activated. It is recommended to add the camera IP addresses to the list of trusted sites.
94/104 D22M Camera Manual Part 1 3.4.6 The First Image in MxControlCenter Download MxControlCenter free of charge from www.mobotix.com MOBOTIX MxControlCenter is a free-of-charge application, which provides a means for displaying and managing many MOBOTIX cameras and their alarms on one computer. On top of this, MxControlCenter can simultaneously display 30 MOBOTIX cameras with 30 frames per second in CIF format and MxPEG encoding on a standard Pentium 4 computer with 3 GHz.
D22M Camera Manual Part 1 95/104 Installing MxControlCenter If you have an MxControlCenter installation CD, insert it into your computer drive. If this is not the case or if you would like to update an older version, you can download the latest MSI or ZIP file from the MOBOTIX website. The latest version is available at www.mobotix.com > Support > Software Downloads in the MxControlCenter section.
96/104 D22M Camera Manual Part 1 Using MxControlCenter for the First Time Double-click the shortcut created by the installer (see Installing MxControlCenter) or the program file itself to start MxControlCenter. Automated Search for MOBOTIX Cameras If you start MxControlCenter for the first time or if you have not yet stored a start layout with the desired video sources (i.e. MOBOTIX cameras), the Open Video Sources dialog will open and automatically starts scanning the network.
D22M Camera Manual Part 1 97/104 Click on OK to add the selected cameras to the Open Video Sources dialog. Anytime you connect a new camera to the local network, you can initiate the search in the Open Video Sources dialog again by pushing the button. If the desired MOBOTIX cameras are shown as OK in the video source list (status OK), proceed to the Selecting Video Sources section further below.
98/104 D22M Camera Manual Part 1 MxControlCenter changes the network configuration of the current camera and, after a short time, the camera also appears in the list with a new IP address and in the same subnet as your computer. Make sure that the Save camera configuration permanently checkbox is activated so that the new network settings will be used from now on and not just until the camera's next reboot.
D22M Camera Manual Part 1 Editing the Video Source List This list provides a popup menu (right mouse key), allowing you to select/deselect all video sources at once. Similarly, you can highlight some or all of the listed video sources and remove them from the list if they are not to be displayed or managed in MxControlCenter.
100/104 D22M Camera Manual Part 1 3.5 Starting the Camera With an Automatic IP Address (DHCP) If your network has a DHCP server, you can start the camera with DHCP support. In this case, the DHCP server automatically assigns an IP address. Connect and activate the external speaker of the camera! As soon as startup has been completed, the camera automatically announces its IP address, its network mask and its MAC address (note that this feature requires an external speaker).
101/104 D22M Camera Manual Part 1 3.6 Starting the Camera Using the Factory IP Address In certain situations, it may become necessary to start the camera with its factory IP address. This could be the case, for example, if the IP address has been lost or the camera does not react to the last known IP address.
102/104 D22M Camera Manual Part 1 Declaration of Conformity © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22M Camera Manual Part 1 Note Find the most recent certificates for this camera and other MOBOTIX products on our website www.mobotix.com in the Support > Certificates section. Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
104/104 D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX – The HiRes Video Company To demonstrate our confidence in the quality of our products, MOBOTIX cameras were used to capture all the images that appear in this manual. Manufacturer Executive Board MOBOTIX AG Dr. Ralf Hinkel Kaiserstrasse D-67722 Langmeil Registration Office: Kaiserslautern Local Court Germany Registration Number: HRB 3724 Tel : +49 6302 9816-103 Tax Code: 44/676/0700/4 Fax: +49 6302 9816-190 Tax Office: Worms-Kirchheimbolanden, Germany http://www.mobotix.
D22M-IT/SECURE: Drilling Template Scale 1:1 1 00 mm/3.94 in 1 00 mm/3.94 in ø5.5 mm/ 0.22 in . 41 1 ø 7i 5 . 5 m/ m 4 n © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22M-BASIC: Drilling Template Scale 1:1 ø90 mm/3.54 in 22.5 mm/ 0.89 in 67.5 mm/2.66 in 45 mm/1.77 in ø5.4 mm/0.21 in 78 mm/3.07 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22M On-Wall Set: Drilling Template Scale 1:1 60 mm/2.36 in 1 00 mm/3.94 in ø5.8 mm/0.23 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
71 .5 mm/2.82 in D22M Outdoor Wall Mount: Drilling Template Scale 1:1 50 mm/1 .97 in 3 mm/0.1 2 in ø7.5 mm/0.3 in 1 20 mm/4.72 in 86 mm/ 3.39 in 86 mm/3.39 in ø7.5 mm/0.3 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22M In-Ceiling Set: Drilling Template Scale 1:1 i 5.9 / mm 0 ø1 5 n © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
3 mm Beschnitt umlaufend 3 Megapixels 2048 x 1536 8x software zoom -22°F to +140°F Weatherproof -30°C to +60°C, IP65 no heating necessary D22M X Camera Manual Part 1 IEEE 802.
