3 mm Beschnitt umlaufend Megapixel 1280 x 960 software zoom VGA (640 x 480) 10 fps Mega -22°F to +140°F Weatherproof CamIO X MOBOTIX User Manual IEEE 802.
MOBOTIX CamIO User Manual Caution Only qualified personnel may install and open the CamIO and connect it to the mains power; make sure that the relevant regulations of your country are respected! It is imperative that all electrical wires have been disconnected from the mains power when working on or servicing the CamIO! Please also make sure to adhere to the applicable regulations for this kind of work! MOBOTIX will not assume any responsibility for damages from faulty installations or inappropriate use!
1/56 MOBOTIX CamIO User Manual CamIO User Manual 1 INTRODUCTION 4 1.1 MOBOTIX CamIO Concept 6 1.2 The MOBOTIX CamIO and MOBOTIX Cameras 1.2.1 Functional Overview of the CamIO Models 1.2.2 Connection Cables between CamIO and MOBOTIX Cameras 8 8 9 1.3 1.3.1 1.3.2 1.3.3 1.3.4 1.3.5 1.3.6 1.3.7 1.3.8 1.3.
2/56 MOBOTIX CamIO User Manual 3 OPERATION OF THE CAMIO 42 3.1 Activating the CamIO 42 3.2 3.2.1 3.2.2 3.2.3 3.2.4 3.2.5 Configuration Sample Functional Overview Terminal Connections of the CamIO Overview of the Configuration Steps Configuring the MOBOTIX Camera Configuring a Softphone 43 43 44 44 45 51 4 TECHNICAL SPECIFICATIONS 52 APPENDIX: DECLARATION OF CONFORMITY DRILLING TEMPLATE (SCALE 1:1) Download the latest version of this document as a PDF file from www.mobotix.
MOBOTIX CamIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
4/56 MOBOTIX CamIO User Manual 1 All CamIO models can be used with the MOBOTIX M12 and M22 cameras (IT and Secure models). The CamIO can switch Ohm resistive loads with max. 5 A, (max. 500 W lamps at 230 V or 300 W lamps at 115 V). INTRODUCTION The MOBOTIX CamIO is the expansion box for connecting the MOBOTIX cameras M12 and M22M (IT and Secure models).
5/56 MOBOTIX CamIO User Manual When mounting the MOBOTIX CamIO, the foot of the CamIO wall mount replaces the original foot of an M12 or M22 camera mount. The foot of the CamIO wall mount covers the CamIO and reliably protects it against atmospheric exposure (IP65). In addition, the foot of the CamIO wall mount also contains an additional speaker, which is more powerful than the camera's internal speaker. CamIO models • CamIO-PoE: This model is supplied using PoE (IEEE 802.
6/56 MOBOTIX CamIO User Manual 1.1 MOBOTIX CamIO Concept Simple Installation When designing the MOBOTIX CamIO, special focus was placed on easy installation of the expansion box. The supplied drilling template facilitates mounting the CamIO and connecting the cabling for devices and data connections is easy, secure and weatherproof.
MOBOTIX CamIO User Manual Backup power using the CamIO-ACplus The integrated rechargeable battery of the CamIO-ACplus model can bridge smaller power failures and thus protects the integrity of the video and audio data. At room temperature (20°C/68°F), the CamIO can power a MOBOTIX M12D for about 45 minutes; at -20°C (-4°F), the CamIO still provides 20 minutes of backup power. Providing backup power for an M22M using a CamIO-ACplus is currently not possible.
8/56 MOBOTIX CamIO User Manual 1.2 The MOBOTIX CamIO and MOBOTIX Cameras CamIO-PoE Mx-CAMIO-POE CamIO-AC Mx-CAMIO-AC-230 Mx-CAMIO-AC-115 CamIO-ACplus Mx-CAMIO-ACPLUS-230 Mx-CAMIO-ACPLUS-115 1.2.1 Functional Overview of the CamIO Models Outdoor - weatherproof IP65 IP65 IP65 Power Supply PoE 230 V~ / PoE 115 V~ / PoE 230 V~ / PoE 115 V~ / PoE Integrated rechargeable battery - - X Concealed cabling X X X All CamIO models can be used with MOBOTIX M12 and M22 cameras (IT/Secure models).
9/56 MOBOTIX CamIO User Manual 1.2.2 Connection Cables between CamIO and MOBOTIX Cameras Two cables are required to connect the MOBOTIX camera to the CamIO: • Ethernet cable: Establishes the data connection and the power supply to the camera. • Control cable: Connects the serial interface (M12) or the USB interface (M22) of the camera in order to provide the signal outputs and inputs of the camera at the CamIO. The different cameras require different control cables, which need to be ordered separately.
10/56 MOBOTIX CamIO User Manual 1.3 Important Notes 1.3.
11/56 MOBOTIX CamIO User Manual Allowed Cable Dimensions Solid AWG Bottom terminal (terminals 1 to 16) 0.14 to 2.5 mm2 26 to 14 Ethernet terminal (cutting clamps) 0.13 to 0.31 mm2 26 to 22 Cable diameters should be tailored to the electrical load and must follow the applicable regulations. Note The length of the cables for signal wires and external sensors is not restricted.
12/56 MOBOTIX CamIO User Manual Fire Prevention When installing the power lines to the camera, make sure you always adhere to the relevant regulations on wiring and fire prevention at the site of the installation. Lightning and Surge Protection To prevent damage from lightning and power surges, make sure you follow these guidelines: • Lightning conductors: In areas exposed to lightning (e.g.
MOBOTIX CamIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
14/56 MOBOTIX CamIO User Manual 2 MOUNTING 2.1 Delivered Parts, Components, Dimensions and Connectors 2.1.1 Delivered Parts and Components Allen screws M6x40 (item 6) Washers ø6.4 mm (item 7) Speaker with audio cables (item 11) Allen wrench 5 mm (item 12) NET plug (item 5) Screw caps for wall mount (item 10) The control cable required for connecting the camera to the CamIO is not part of the standard delivery. Always order the corresponding control cable for your M12 or M22.
15/56 MOBOTIX CamIO User Manual 2.1.2 Wall Mount Foot and Housing The MOBOTIX CamIO housing (item 1) and the housing of the CamIO itself (item 2) are made of white, fiber-reinforced plastic (PBT-30GF, Polybutyleneterephtalate with 30% fiberglass). This material is used heavily in the automotive industry and is sturdy, resistant against high temperatures, environmental influences, chemicals, etc.
16/56 MOBOTIX CamIO User Manual 2.1.3 Dimensions and Drilling Template The appendix of this manual contains a 1:1 drilling template for drilling the dowel holes for the CamIO. 100 mm/3.94 in Dimensions of the MOBOTIX CamIO Housing 100 mm/3.94 in 25 mm/1 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
17/56 MOBOTIX CamIO User Manual 162.5 mm/6.5 in Dimensions of the MOBOTIX CamIO Housing with Wall Mount Foot 136 mm/5.4 in 158 mm/6.22 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
18/56 MOBOTIX CamIO User Manual © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX CamIO User Manual © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
20/56 MOBOTIX CamIO User Manual 2.1.4 Connectors and Wiring Terminal Connector for Power Supply, External Devices, Sensors and Audio Devices Make sure that you are adhering to the applicable regulations in your country regarding the allowed cables when connecting the wires to the terminal connector. Always observe the allowed wire cross-sectional sizes (see table below).
21/56 MOBOTIX CamIO User Manual Terminal Connector and Wiring of the Ethernet Connector Make sure that you are using a standard CAT5 Ethernet cable for connecting the Ethernet cable to the Ethernet terminal connector (see section 2.4.3, Ethernet Connection of the CamIO). Always observe the allowed wire cross-sectional sizes and the applied connection standard. The color codes of the individual wires are usually easy to spot at a CAT5 plug.
22/56 MOBOTIX CamIO User Manual 2.2 Information on Connecting the MOBOTIX CamIO The CamIO can be used with a MOBOTIX M12 or an M22. Simply replace the original foot of the corresponding SecureFlex mount of the camera by the supplied foot of the CamIO wall mount. MOBOTIX M12 with CamIO MOBOTIX M22M with CamIO © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX CamIO User Manual Mounting the CamIO in four steps Mounting the CamIO is done in four steps (or three, if no external devices are connected; skip step 3 in this case): 1) Preparing the camera: Mounting the CamIO Wall Mount and the Control Cable Replace the foot of the original SecureFlex wall mount against the foot of the CamIO wall mount. This step includes connecting the M12/M22 control cable to the camera and guiding it and the network cable into the CamIO wall mount (section 2.3).
24/56 MOBOTIX CamIO User Manual 2.3 Mounting the CamIO Wall Mount and the Control Cable 2.3.1 Mounting with an M12 Camera • Unscrew the upper Allen screw in the original foot of the mount, which holds the turn/tilt unit in place (5 mm Allen wrench, item 12). Remove the Allen screw, the washer and the hex nut from the mount. • Remove the cover. • Gently pull the turn/tilt unit and all cables out of the vertical opening of the original wall mount foot.
25/56 MOBOTIX CamIO User Manual • Insert the M12 control cable for the CamIO from below into the turn/tilt unit of the camera. Remove the blue plug labeled RS-232 from the insect protection. Connect the HD 15 connector to the M12. • Make sure that the camera's insect protection remains firmly in place. Reinstall the bottom cover of the mount. • Insert the Ethernet cable and the M12 control cable from below into the turn/tilt unit of the CamIO wall mount foot.
26/56 MOBOTIX CamIO User Manual 2.3.2 Mounting with an M22 Camera • Unscrew the upper Allen screw in the original foot of the mount, which holds the turn/tilt unit in place (5 mm Allen wrench, item 12). Remove the Allen screw, the washer and the hex nut from the mount. • Remove the cover. • Gently pull the turn/tilt unit and all cables out of the vertical opening of the original wall mount foot.
27/56 MOBOTIX CamIO User Manual • Insert the Ethernet cable and the M22 control cable from below into the turn/tilt unit of the CamIO wall mount foot. • Insert the supplied cover into the free opening of the CamIO wall mount foot. • Insert the turn/tilt unit of the camera into the vertical opening of the mount (all the way to the stop). • Place the hex nut into the corresponding hole, insert the Allen screw with washer and lightly fasten the screw so that you can still easily turn the camera.
28/56 MOBOTIX CamIO User Manual 2.4 Mounting the CamIO Housing and Installing the Cables 2.4.1 Mounting the CamIO Housing on the Wall The appendix of this manual contains a 1:1 drilling template for mounting the CamIO. Use this template for drilling the holes for the dowels. • Mount the CamIO using the supplied screws, washers and dowels.
MOBOTIX CamIO User Manual 29/56 2.4.2 Power Supply of the CamIO You can supply power to the MOBOTIX CamIO using one of these two methods: • Direct power supply: Mains power (230 V~/115 V~) is connected to terminals 1 and 2 of the CamIO's terminal connector at the bottom. The CamIO will power a MOBOTIX camera and an external device attached to terminals 3 and 4. The external device will get the same voltage that has been connected to terminals 1 and 2 of the CamIO.
30/56 MOBOTIX CamIO User Manual Installing the power supply: Use a two-wire cable (or any other suitable cable) to provide the power supply. Make sure that you are respecting the minimum cable diameters. Caution The power supply cable to the CamIO needs to have a basic insulation level (BIL) of at least 230 V/115 V (depending on the mains voltage). Never lay bell wires (BIL 50 V) next to 230 V or 115 V cables! Make sure that the fuse for this cable is not stronger CamIO than 16 A.
MOBOTIX CamIO User Manual 31/56 Connect the power supply to the CamIO: • Puncture the blue seal with the end of the black/brown wire (phase conductor L) and guide it into terminal 1. Tighten the screw to lock the wire in place. • Puncture the blue seal with the end of the blue wire (neutral N) and guide it into terminal 2. Tighten the screw to lock the wire in place.
32/56 MOBOTIX CamIO User Manual 2.4.3 Ethernet Connection of the CamIO • Remove the outer insulation (sheath) of the Ethernet cable and guide it through the proper opening at the bottom of the CamIO housing on the right–hand side (see figure). Make sure that you are respecting the cable assignment and the minimum cable diameters. For additional information on this topic, see chapter 4, Technical Specifications. • Lift all clamps of the Ethernet terminal.
MOBOTIX CamIO User Manual 2.5 Connecting External Components to the CamIO 2.5.1 Connecting External Devices, Sensors and Audio Devices The MOBOTIX CamIO supplies connectors for the following functions: • • • • Switch and supply power to external devices without individual power supply with loads of up to 5 A. Potential-free switching of external devices with individual power supply and with loads between 100 mA and 5 A. Connect external sensors to the signal inputs of the camera (e.g.
34/56 MOBOTIX CamIO User Manual Make sure that you follow the terminal assignment of the CamIO's bottom terminal connector. Connecting and sealing the cables follows the same instructions as for power cables (see section 2.4.2, Power Supply of the CamIO). Make sure that you are adhering to the applicable regulations in your country regarding the allowed cables when connecting the wires to the terminal connector.
MOBOTIX CamIO User Manual MOBOTIX CamIO Connection Example © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
36/56 MOBOTIX CamIO User Manual 2.6 Mounting the Camera on the CamIO Once the camera has been mounted to the foot of the CamIO wall mount, the Ethernet and control cables have been connected and optional external devices have been attached, you can mount the CamIO/camera assembly to the CamIO housing. 2.6.1 Connecting the Additional Speaker in the Wall Mount Foot The foot of the wall mount has a built-in speaker, which can be used for audio output in connection with MOBOTIX M12 cameras.
37/56 MOBOTIX CamIO User Manual 2.6.2 Connecting the Ethernet and the CamIO Control Cables In order to connect the camera to the CamIO, you need to attach the Ethernet and control cables of the camera to the CamIO. • Insert the cover into the guides at the bottom of the CamIO housing (1) and press at the top of the cover until it clicks in place (2).
38/56 MOBOTIX CamIO User Manual 2.7 Wiring, Fire Prevention, Lightning and Surge Protection When installing the wiring inside or outside of buildings, make sure you always adhere to the relevant regulations on wiring, fire prevention and protection against lightning.
MOBOTIX CamIO User Manual • Surge protection: Make sure you have installed proper protection against electrical surges in order to prevent damage to the camera, the building and the network infrastructure. This includes surge protectors for 19" racks, adding an uninterruptible power supply (UPS) to the MOBOTIX camera, and installing surge arresters or similar for routers, switches, servers, etc. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
40/56 MOBOTIX CamIO User Manual 2.8 Accessories, Replacement Parts CamIO Wall Mount Foot The wall mount foot is used for mounting the camera to the MOBOTIX CamIO. CamIO Housing Replacement housing for all CamIO models. M12 Control Cable (MX-CAMIO-OPT-M12) Control cable for connecting the CamIO and an M12 camera. M22 Control Cable (MX-CAMIO-OPT-M22) Control cable for connecting the CamIO and an M22M camera. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX CamIO User Manual Cable Seals The seals will protect the cables against water that could be entering along the wires. M22 NET Plug Plug for sealing off the Ethernet cable on M22M camera models. M22 USB Plug Plug for sealing off the USB cable on M22M camera models. Additional CamIO Speaker Replacement speaker with audio cables for the CamIO wall mount foot. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
42/56 MOBOTIX CamIO User Manual 3 OPERATION OF THE CamIO 3.1 Activating the CamIO Once the CamIO and the MOBOTIX camera have been properly installed (see chapter 2), you can set up the camera for proper operation. To begin with, it is necessary to establish the power supply of the CamIO (either 230 V/115 V directly or indirectly via the network cabling using a PoE switch).
MOBOTIX CamIO User Manual 43/56 3.2 Configuration Sample The following example of a door intercom system demonstrates one possible application and shows the steps for properly configuring a MOBOTIX M12 with a CamIO-AC/ACplus. Make sure that you have installed and setup the CamIO and the MOBOTIX camera as described in chapter 2. Sample: Door intercom system with Video SIP and additional lighting 3.2.
44/56 MOBOTIX CamIO User Manual ter the building. If required, the receptionist can manually switch the additional lighting using the softphone keys: key 3 to switch the lights on and key 9 to switch them off again. In the meantime, the camera is automatically recording the video and audio stream on a file server. Furthermore, the CamIO's rechargeable battery (CamIOACplus models only) protects the MOBOTIX camera against short-time power failures.
MOBOTIX CamIO User Manual 3.2.4 Configuring the MOBOTIX Camera 1) Activate arming of the camera • Activate arming (Setup Menu > General Event Settings). 2) Configure recording • Set up event storage on an external file server (Admin Menu > Event Storage). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
46/56 MOBOTIX CamIO User Manual • Activate recording for VM event (Setup Menu > Recording). • Activate VM event and set up video motion window (Setup Menu > Event Settings). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX CamIO User Manual 3) Configure SI event and switching of additional lighting (SO action) • Configure SO action and activate action profile (Setup Menu > Actions). 4) Configure SI event and voice message (SD action) • Activate and configure the speaker and the microphone (volume, microphone sensitivity in Admin Menu > Loudspeaker and Microphone); set Audio Input temporarily to Microphone (only required when recording the voice message via the camera microphone).
48/56 MOBOTIX CamIO User Manual • Set Audio Input to Line In (Admin Menu > Loudspeaker and Microphone; audio comes from the door intercom system's microphone). • Set up and activate SI event (Setup Menu > Event Settings). • Set up and activate SD message (Setup Menu > Messaging 2), select SI event and recorded voice message. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX CamIO User Manual 5) Configure SI event and VoIP phone call (CL message) For more information on setting up the SIP telephony features of MOBOTIX cameras, read chapter 9, Telephony Features in the Software Manual. • Configure the VoIP settings and activate VoIP (Admin Menu > VoIP Settings). • Set up a phone profile (Admin Menu > Phone Profiles). © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
50/56 MOBOTIX CamIO User Manual • Add CL message to messaging profile and select phone profile (Setup Menu > Messaging 2; SD message has already been configured). 3.2.5 Configuring a Softphone • Configure the softphone and make sure that it is running on the computer. For more information on setting up a softphone for use with MOBOTIX cameras, read chapter 9, Telephony Features in the Software Manual. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX CamIO User Manual Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
52/56 MOBOTIX CamIO User Manual CamIO-AC Mx-CAMIO-AC-230 Mx-CAMIO-AC-115 CamIO-ACplus Mx-CAMIO-ACPLUS-230 Mx-CAMIO-ACPLUS-115 TECHNICAL SPECIFICATIONS CamIO-PoE Mx-CAMIO-POE 4 Outdoor - weatherproof IP65 IP65 IP65 Power Supply PoE 230 V~ / PoE 115 V~ / PoE 230 V~ / PoE 115 V~ / PoE Integrated recharg. battery - - X Concealed cabling X X X Using the backup power feature of the CamIOACplus requires a MOBOTIX M12. M22 cameras do not support this feature yet.
53/56 MOBOTIX CamIO User Manual Allowed Cable Diameters and Cable Lengths Allowed Outer Diameters Sheathed cables 3-wire cable 5-wire cable 8.2 to 11.0 mm (5/16 to 7/16 in) 9.5 to 12.5 mm (3/8 to 1/2 in) Note ETHERNET CAMERA ETHERNET Make sure that the length of the Ethernet cable does not exceed 100 m (300 ft). The length of the cables for signal wires and external sensors is not restricted. You need to make sure, however, that the minimum voltage at the corresponding terminal is reached.
54/56 MOBOTIX CamIO User Manual Terminal Connector for Power Supply, External Devices, Sensors and Audio Devices AWG: American Wire Gauge (for measuring cable diameters) Allowed Cable Dimensions Solid AWG 2 Bottom terminal (terminals 1 to 16) 0.14 to 2.5 mm 26 to 14 Cable diameters should be tailored to the electrical load and must follow the applicable regulations.
55/56 MOBOTIX CamIO User Manual Terminal Connector and Wiring of the Ethernet Connector Allowed Cable Dimensions Ethernet terminal (cutting clamps) Solid AWG 0.13 to 0.31 mm2 26 to 22 Cable diameters should be tailored to the electrical load and must follow the applicable regulations.
56/56 MOBOTIX CamIO User Manual Declaration of Conformity © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
MOBOTIX – The HiRes Video Company To demonstrate our confidence in the quality of our products, MOBOTIX cameras were used to capture all the images that appear in this manual. Manufacturer Executive Board MOBOTIX AG Dr. Ralf Hinkel Kaiserstrasse D-67722 Langmeil Registration Office: Kaiserslautern Local Court Germany Registration Number: HRB 3724 Tel : +49 6302 9816-103 Tax Code: 44/676/0700/4 Fax: +49 6302 9816-190 Tax Office: Worms-Kirchheimbolanden, Germany http://www.mobotix.
3 mm Beschnitt umlaufend Megapixel 1280 x 960 software zoom VGA (640 x 480) 10 fps Mega -22°F to +140°F Weatherproof CamIO X MOBOTIX User Manual IEEE 802.
