Quick Start Guide NTC-40 Series - M2M WiFi Router
Quick Start Guide This guide covers the NTC-40 Series M2M WiFi Rotuers. This guide provides a series of step by step instructions to ensure the configuration of your router goes as smoothly as possible. Please check that you have received all the items in your package: Description QTY NTC-40 Series M2M WiFi Router 1 Ethernet cable 1 Power Supply Unit 1 Antennas 4 Quick Start Guide 1 | Wireless M2M If any of these items are missing, please contact NetComm Technical Support.
NTC-40 Series - M2M WiFi Router Overview of LEDs LED Display Description Power (red) Solid ON The red Power LED indicates correct power is applied to the DC power input jack. Tx/Rx (amber) Solid ON The amber LED will light upon data being sent to or received from the cellular network. DCD (green) Solid ON The green Carrier Detect LED illuminates to indicate a Data connection. Service Type (green) The green LED will illuminate when cellular network coverage is detected.
Overview of the Cellular Router Interfaces SMA Female For Main 3G antenna connection Mini USB Port For insertion of the Mini USB cable SMA Female SIM Card Bay For receive diversity antenna connection For insertion and removal of the SIM card Reverse Polarity SMA Female Jack For WiFi antennas Ethernet Port Connect to a terminal using RJ45 cable Reset Button | Wireless M2M Push to reboot the router or enter recovery mode 4 2Way Captive Power Terminal Block Voice (RJ-11) Port* Power terminal bloc
NTC-40 Series - M2M WiFi Router Configuring your Router You will need an active SIM card to configure your router. Step 1: Insert the SIM card Press the SIM Eject button to eject SIM card bay. Make sure the SIM card is inserted correctly by inserting the SIM the gold side facing down in the direction as shown below: Press the SIM Eject Button Insert SIM Card Step 2: Set up the Router Connect the supplied antennas to the Router by screwing them onto the antenna connectors.
Step 3: Connect Your Computer Connect one end of the supplied Ethernet cable into the Ethernet port of your router. Connect the other end of the cable into the LAN port of your computer. Wait a few seconds for your computer to establish connection with the router. If the connection is not established automatically, verify that your | Wireless M2M computer is configured to obtain an IP address automatically.
NTC-40 Series - M2M WiFi Router Step 4: Access Your Router’s Homepage The NTC-40 Series router’s homepage can be accessed by using the web address http://my.router, or alternately via default IP address http://192.168.1.1. This URL opens the management console, where you can: View the status of your router. Make changes to the routers configurations.
Step 5: Unlocking the SIM If the SIM card is locked you will need to unlock it with the appropriate PIN code. You can find out if the SIM is locked by viewing the SIM Status on the Status page: If the SIM Status is “SIM PIN Required”, then follow the steps below to unlock the SIM card: From the menu, select Internet Settings -> Mobile Broadband -> SIM Security.
NTC-40 Series - M2M WiFi Router Step 6: Connect to the Internet Your router should automatically connect to the Internet if the SIM status reads “SIM OK”. If it does not, follow the steps listed below to setup the Mobile Broadband connection. By default, the router is set to automatically configure the mobile broadband connection. It tries to detect the correct APN and connection details in order to connect to your Mobile Broadband service.
Select a profile name from the pull down menu to save the profile settings. You can configure and save the mobile broadband settings the router will use to connect to a particular network. Enter the connection details (APN Name) provided by your mobile broadband service provider. You may need to enter a Username and Password provided by your Mobile Broadband service provider. Ensure the Mobile Broadband Connection radio button is set to Enable. Click Save.
NTC-40 Series - M2M WiFi Router Wireless LAN Connection The WiFi Network Name (SSID) and WiFi Security Key are unique for your device and are printed on the back of your NTC-40 Series router. The credentials are also printed on the Wireless Security Card.
Product Warranty NetComm Wireless products have a standard 12 months warranty from date of purchase. Technical Support For firmware updates or if you have any technical difficulties with your product, please refer to the support section of our website. support.netcommwireless.com NETCOMM WIRELESS LIMITED ABN 85 002 490 486 Head Office, 18-20 Orion Road Lane Cove, Sydney, NSW 2066, Australia p: e: +61 2 8205 3888 f: +61 2 9424 2010 m2msales@netcommwireless.com www.netcommwireless.
