Digital satellite antenna with control panel MobilSat+ Mounting instructions Models MSP-S / MSP-C
SUMMARY 1. 2. Introduction...............................................................................................................................................2 Safety instructions.....................................................................................................................................3 2.1. Proper use (for the intended purpose).................................................................................................3 2.2. Safety during installation work.........
MobilSat + Mounting instructions 2. Safety instructions 2.1. Proper use (for the intended purpose) The MobiSat+ is designed to receive digital TV and radio programs via satellite. The turntable can be used to receive digital TV and radio signals in the frequency range from 10.70 to 12.75GHz. Any use other than that specified above will void the warranty or guarantee.
MobilSat + Mounting instructions Modifications to the electrical installations in the vehicle should only be carried out by a specialist in vehicle electrics. Do not make any unauthorized changes to the turntable. 2.4. Adhesive sealant The turntable is attached to the roof of the vehicle by adhesive and is secured by additional fixing screws. Note that the curing of the adhesive sealant is temperature-dependent. It reaches its full strength only after approximately five days. 2.5.
MobilSat + Mounting instructions 5. Unpacking and preparation Please keep original packaging material because it will be needed in case of system return for repair or maintenance actions. In other cases the supplier will not be responsible for damages occurred during transport. Please keep packaging materials out of reach of children. 6. Mounting instructions 6.1.
MobilSat + Mounting instructions For a complete rotation of the antenna during the normal operation the roof of the vehicle must be free of obstacles, as displayed in the following figure. NOTE For difficult installations caused by space problems, it must be underlined that the plate and the LNB arm turns at a minimum height of 25 centimeters. Any obstacles present in the rotation area but lower than 25 cm will not influence normal antenna operations. 6.3.
MobilSat + Mounting instructions Seal also the edges of the assembly plate, as displayed in the following figure. 6.4. Mounting of the external system Connect the cable set to the external unit. The cable can be plugged in the proper connector using the dedicated space in the lower part of the unit.
MobilSat + Mounting instructions Notes for power supply on trailers Often trailers don’t have a stable power supply, or they don’t have a battery at all. In these cases it’s necessary to power the system using a 220V/12V voltage transformer connected, directly to the main line. Do not use in any circumstance battery chargers, economic transformers or nonstabilized power packs. The voltage that feeds the system must be electronically stabilized and must have a nominal voltage of 13.
MobilSat + Mounting instructions 6.10. Connection to the satellite receiver Now it’s possible to connect the antenna system to the satellite receiver, using the F-connector cable. 6.11. Installation menu All the functions of the system are activated using the control panel, showed in the following picture. To activate operator menu press simultaneously the UP/DOWN keys for at least 3 seconds. The system is password protected.
MobilSat + Mounting instructions USER MENU In every menu, except “Mech. Zero Set” e ”Factory settings”: Keys UP/DOWN pressed simultaneously for more than 3 seconds Menu’ XX OK menu INSERT PASSWORD Digit selection XXXX Select from list (scroll menù blocked) Change value FAULTY NO PASSWORD CORRECT? PASSWORD OK menu OK menu Confirm password Confirm selection YES SET ANTENNA SELECT LANGUAGE PREDEF SAT N.1 MECHANICAL ZERO ENGLISH HOT BIRD Mechanical reset (see next page) PREDEF SAT N.
MobilSat + Mounting instructions RESTORE SET ANTENNA DEFAULT SETTINGS MECHANICAL ZERO OK menu OK menu SEARCH FOR MECH ZERO EXECUTION MOTORS ACTIVATED UNTIL END OF ROTATION AND ELEVATION CONFIRM DEFAULT SETTING? NO ACTIONS FOR MORE THAN 5 SEC.
MobilSat + Mounting instructions 7. Technical data Power supply:...………………………………..…. 11/16V Current consumption stand-by mode:………….. 60mA Current consumption during sat search:……..... 2A typ - 3,5A peak Typical time for sat search:……………………….30-60 sec Max time for sat search:……….…. …………….. 300 sec External unit weight:……………………………….15,5Kg 8.
