User's Guide

ManualsBrandsMobilitySound ManualsElectronicsBluetooth LE scanner trigger

FINGER PICK

Model Name: Bluetooth LE scanner trigger

Quick User Guide

INTRODUCTION

The purpose of the Finger Pick finger button is to turn on the barcode reader of a Honeywell

Android device to be able to read barcodes while holding the device on your wrist. This way

you can easily transform your hand held PDA into a wearable PDA. To work it is necessary

to install the dedicated Android application.

SAFETY INFORMATION

● Only operate the Bluetooth Finger Pick in accordance with its purpose.

● Do not operate or charge this product near any liquid(s).

● Do not use abrasives, thinners, alcohol, solvents or aerosol cleaners that may cause

damage to the Bluetooth Finger Pick.

● If the die-cast chassis or other parts are damaged, do not touch the damaged parts.

● This product contains a lithium-polymer rechargeable battery, which is permanently

built-in. To dispose of, be sure to comply with the laws and regulations in your

country or region.

● Do not charge for longer than the specified time.

● Do not bend or drop the product, or otherwise expose it to strong physical impact.

● Never disassemble or modify the product.

● Do not expose the product to high temperatures, high humidity or direct sunlight.

Specification

● Bluetooth LE button

● Operating Temp: -20℃±2℃ ~ 50℃±2℃

● Approx. Weight: 20g

● Bluetooth version: Bluetooth V4.0

● Battery: Li battery

● Battery life: 180 days

Summary of content (7 pages)

PAGE 1
FINGER PICK Model Name: Bluetooth LE scanner trigger Quick User Guide INTRODUCTION The purpose of the Finger Pick finger button is to turn on the barcode reader of a Honeywell Android device to be able to read barcodes while holding the device on your wrist. This way you can easily transform your hand held PDA into a wearable PDA. To work it is necessary to install the dedicated Android application. SAFETY INFORMATION ● ● ● ● ● ● ● ● ● Only operate the Bluetooth Finger Pick in accordance with its purpose.
PAGE 2
Federal Communication Commission Interference Statement Model: FP2 FCC ID. : XTS-FP2 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
PAGE 3
USER MANUAL CHARGING AND BATTERY Charging of the Bluetooth Finger Pick is done via the Type-C USB connector. Use a standard USB connection or charger supporting: 5V - 1A. During charging, the LED shows a solid Red color. When the battery is fully charged, the LED either turns off. If during operation the battery level goes low the LED show a solid Red color to indicate the battery need to be recharged. With a fully charged battery, the expected operational time is above 3 months.
PAGE 4
USE ANDROID APPLICATION 1. Install the application from Google Play Store (recommended for automatic updates). Search “Finger Pick Lexter” on the Play Store from your Honeywell device or scan the QR code below. Alternatively use the URL below or scan the QR code below www.lexter.com/download/honeywell.apk 2. Open the installed application. The name of the app is “Lexter Wearable”. 3.
PAGE 5
Pair to Honeywell device 4. Tap on Bluetooth trigger configuration 5. Allow app to turn on the bluetooth (This point only if bluetooth is not enabled) 6.
PAGE 6
Widget You can add the widget on the home screen to unpair the button easily. Open the app and tap to “Bluetooth unpair shortcut” for add the widget Unpair it is recommended to use the widget as described above.
PAGE 7
Important Note If a finger pick is connected to a device, you must first unpair it in order to connect it to another device. It is therefore recommended to use the widget to unpair the device at the end of the work. LED EVENTS LED Power ON Blue LED double flash Power OFF Blue LED solid ON until the power button is released LED FUNCTION Turned off The device is turned off or the battery charging is complete.