PS6S1800M Serial/Modem Charging Cradle Mobility Electronics, Inc 9918 Via Pasar, San Diego, CA 92126, USA Phone: (858) 880-2225 Fax: (858) 530-2733 www.invisioncradles.
invision Serial/Modem Charging Cradle User Guide Copyright© 2005 Mobility Electronics, Inc. All rights reserved. The information in this document is subject to change without notice. Disclaimer Mobility Electronics, Inc. assumes no responsibility for any damage or loss resulting from the use of this user guide. Mobility Electronics, Inc. assumes no responsibility for any loss or claims by third parties that may arise through the use of this product. Mobility Electronics, Inc.
invision Serial/Modem Charging Cradle User Guide Contents CONTENTS .......................................................................................... III INTRODUCTION ..................................................................................... 1 Setting up the PS6S1800M.......................................................................... 2 Product/Technical Support .......................................................................... 7 Appendix A – Regulatory Information ........
invision Serial/Modem Charging Cradle User Guide Introduction The invision PS6S1800M serves as an essential data communications device, enabling you to synchronize the information on your Symbol® SPT 1700 or SPT 1800 terminal and the Palm Desktop software using HotSync® technology. It also charges both your terminal and a spare battery – all while performing HotSync operations via modem or serial connection.
invision Serial/Modem Charging Cradle User Guide Setting up the PS6S1800M Setting up your PS6S1800M is easy and includes only these simple steps. 1. Power Connection 2. HotSync Connection: a. Connect the serial cable to the computer (if you want to HotSync with the computer), or b. Connect the modem (if you want to HotSync with a remote location via the modem) Power Connection To connect your PS6S1800M to your computer: Connect your Symbol’s power adapter into a US standard 110V wall outlet.
invision Serial/Modem Charging Cradle User Guide HotSync with the Computer To HotSync your terminal with data on your computer, follow these simple steps: Plug the RJ-45 connector into the Serial Jack on rear of the PS6S1800M cradle. Turn off your computer and plug the DB-9 connector into the serial communications port on your computer. Change the Modem/Serial Switch to the “Serial” position. Your PS6S1800M requires a dedicated port. It cannot share a port with an internal modem or other device.
invision Serial/Modem Charging Cradle User Guide HotSync with a Remote Location To HotSync your terminal with data at a remote location, follow these simple steps: Connect one RJ-11 end of the included telephone cord into a standard analog telephone wall jack. Connect the other RJ11 end to the “LineIn” jack on the back of the PS6S1800M cradle.
invision Serial/Modem Charging Cradle User Guide Operating the Cradle The Sync Select switch on the back of the PS6S1800M cradle can be set in either of two positions: MODEM Move the switch to the left-hand position for modem communications. While in this position, the cradle automatically wakes up the SPT terminal (if it is asleep), initializes the modem electronics, and performs a modem HotSync when the HotSync button is pressed.
invision Serial/Modem Charging Cradle User Guide Charging the SPT Terminal Battery The cradle may also be used to charge the SPT terminal lithium ion battery. To charge the terminal's battery: 1. Ensure the cradle is powered on. 2. Insert the terminal in the cradle as shown. a. The Terminal Battery Charge LED will turn “RED” to indicate that the terminal is charging. b. When the terminal has completed charging, the light will turn “GREEN” to indicate the battery is fully charged (approximately 3 hours).
invision Serial/Modem Charging Cradle User Guide Product/Technical Support Mobility is committed to providing its customers with first-class customer service and technical support. For your convenience, a few troubleshooting techniques are provided below that might help you fix your problem quickly and easily.
invision Serial/Modem Charging Cradle User Guide Symptom: Attempt by the cradle to HotSync the terminal through the modem failed. Possible Cause The terminal was removed from the cradle while the HotSync was in progress. Action Place the terminal back in the cradle to allow the cradle to make another HotSync attempt. Terminal or cradle was disconnected from the telephone line while the HotSync was in progress. Unplug the modem cable for 30 seconds to allow the local telephone connection to hang up.
invision Serial/Modem Charging Cradle User Guide Symptom: Terminal cannot communicate through the modem. Possible Cause The modem cable is not connected properly. Action Check to be sure the modem cable is connected securely to the cradle and to the analog telephone jack. The cradle is not getting power. Check to be sure the power cable is connected securely to both the cradle and to the AC power. The terminal is not fully seated in the cradle. Remove and re-insert the terminal into the cradle.
invision Serial/Modem Charging Cradle User Guide Symptom: Terminal has successfully connected through the modem, but no data is being transmitted over the connection. Possible Cause Data is being transferred over the S24 radio link. Action To temporarily disable the radio link, and force the data transmission to use the modem connection, follow the instructions provided by the manufacturer for communicating with radio links.
invision Serial/Modem Charging Cradle User Guide Appendix A – Regulatory Information Radio Frequency Interference Requirement FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
invision Serial/Modem Charging Cradle User Guide • • • • • temporary discontinuance of service may be required. Also, you will be advised of your right to file complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment.
invision Serial/Modem Charging Cradle User Guide Greek Italian Spanish Portuguese Malti Estonian Hungarian Slovak Czech Slovene Lithuanian Latvian ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Mobility Electronics ∆ΗΛΩΝΕΙ ΟΤΙ modem ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΑΣ Ο∆ΗΓΙΑΣ 1999/5/ Con la presente Mobility Electronics dichiara che questo modem è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
invision Serial/Modem Charging Cradle User Guide Appendix B – Warranty Mobility Electronics, Inc. warrants this product against defects in materials and workmanship to the original purchaser (or the first purchaser in the case of the remanufactured product being sold) for a period of one (1) year from the date of shipment. This warranty is limited to a repair or replacement of the product. To obtain warranty service, the purchaser must first call Mobility Electronics, Inc.
invision Serial/Modem Charging Cradle User Guide Mobility California, Inc. 9918 Via Pasar, San Diego, CA 92126, USA Phone (858) 880-2225 • Fax (858) 530-2733 Email: invisioncradles@mobl.com • www.invisioncradles.
