Installation and Operating Instructions for Tire Pressure Monitoring System Model No. ：TX014 Contents 1. System Introduction 2. Safety Notices 格式化: 項目符號及編號 3. Applicable Vehicles 格式化: 項目符號及編號 4. Operation and Installation of Wireless Tire Pressure Monitoring System 格式化: 項目符號及編號 4.1 Installation and Mounting of Transmitter. 4.2 Removing Tire with the transmitters inside. 5. Limit Warranty 5.1 Warranty Service 5.2 This Limited Warranty Provided by Mobiletron Does Not Cover 6.
1. System Introduction (1) TX014 is a wireless tire pressure monitoring system with sensors and transmitters mounted in each tire and set by LF Controller. Highly accurate sensors collect tire pressure and temperature data which is transmitted to a Digital Display Receiver. (2) The System monitors the tire data with a LCD display which informs the driver of the condition of the tires while driving.
Mounting the Tire with Transmitter on Wheel Rim 1. Fasten Transmitter on the Wheel Rim 1st. Pass Clamping Strap through Transmitter。 2nd. Position the Transmitter in the lowest area of the concave center well near the valve。 Valve Transmitter Note：It is recommended that the location of each transmitter be recorded to avoid possible damage when tires need to be removed。 3rd.
Position Worm Gear Clamp Opposite to Transmitter Valve 2. Assemble Tire 1st. Place tire under Transmitter as shown below。 Place Tire Changing Valve Machine’s Lever to the Opposite Side of Valve 2nd. Use auto-install machine to install the lower-side of tire onto rim。 Turn in This Direction Slowly Valve 3rd.
Tire Changing Machine’s Lever Has to Come to a Stop Before Valve to Ensure It Won’t Touch Nearby Transmitter Turn in This Direction Slowly Valve 4th. Install whole tire to the wheel。 Place Tire Lever to the Opposite Side of Tire Changing Lever (Contrasting to Valve) to Protect Nearby Transmitter Tire Changing Machine’s Lever Valve 4.
Location of Transmitter Within Tire Tire Changing Machine’s Lever Valve Caution: In order not to damage the transmitter，Tire Level should be placed in the opposite side of valve。 2. Removing the tire from the rim 1st. Place tire onto the installation machine；rub soapy water onto tire bead and rim lip。 Valve Location of Tire Changing Machine’s Lever Tire Lever Transmitter Within Tire 2nd.
Tire Changing Machine’s Lever Manual Tire Lever Turn in This Direction Slowly 3rd. Utilize Manual Tire Lever ， simultaneously with Tire Changing Machine’s Lever，to pull the lower tire bead away from upper side of wheel。 Turn in This Direction Slowly Transmitter Manual Tire Lever 4th. Remove the Transmitter from the rim。 5.
5.1 Warranty Service (1) The above warranty will be honored by the retailer from which it was purchased, provided that the owner can provide dated proof of purchase. (2) In the event that any defect in the unit is covered by the above warranty, Mobiletron will replace the affected components free of charge, shipping prepaid. The owner shall be responsible for any labor and installation costs incurred in removing the defective parts and/or installing the replacement.
Manufacturer: Moniletron Electronic ,Inc. Address: No.39, Sec 3, Chung-Ching Rd., Ta-Ya, Fax: +886-4-25673069 Taichung Hsien, Taiwan 428 Web Site: http://www.more.com.
1. The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
