Installation and Operating Instructions for Tire Pressure Monitoring System Model No.
Contents 1. System Introduction 2. Safety Notices 3. Applicable Vehicles 4. System Package Content 5. Operation and Installation of Wireless Tire Pressure Monitoring System 5.1 Installation and Mounting of Digital Receiver 5.1.1 Utilize the Cooling Vent Holder to fasten the Digital Receiver 5.1.2 Replace Mounted-on-Air-Outlet Digital Receiver 5.2 Installation and Demounting of Transmitter 5.2.1 Mounting the Tire with Transmitter on Wheel Rim 5.2.2 De-Mounting Tire with Transmitter Inside 6.
1. System Introduction (1) TPV03 is a wireless tire pressure monitoring system with sensor/transmitter mounted on each wheel plus a set of Receiver with Display placed in driver's cabin. Highly accurate sensors collect tire pressure and temperature data then transmitted by wireless radio to Digital Receiver. (2) The System monitors the data of tires with LCD digital display thus driver can be well-informed with most updating data of tires while driving.
(5) Transmitter: 4 Units (6) Installation Parts for Transmitter (Nut, Core and Washer – each 4 pcs ) (7) TX rubber ring A : 4 pc (8) TX rubber ring B : 4 pc (7) User Manual: 1 pc 5. Operation and Installation of Wireless Tire Pressure Monitoring System 5.1 Installation and Demounting of Digital Receiver 5.1.1 Utilize the Cooling Vent Holder to fasten the Digital Receiver onto the Air Outlet in driver’s cabin (1) Fasten the Cooling Vent Holder onto the backside of the Digital Receiver.
(2) Screw the Antenna into the Digital Receiver. (3) Fasten the Digital Receiver with the Cooling Vent Holder onto the Air Outlet in the front seat. (4) Plug the DC Power Cable into the Vehicle Cigarette Lighter Socket and Digital Receiver Power Jack. (5) Turn on the Vehicle Power and confirm if the LCD Display shows 4 “??P”. ??P ??P ??P ??P 5.1.
offer any warranty if he installs the product by himself. Tools Required： Tire Changing Equipment Tire Balancing Equipment Torque Wrench 5.2.1 Mounting the Tire with Transmitter on Wheel Rim Notes： Pair Valve Tag that has the same color as the color of text on ID Number Label of Transmitter for the identical tire as indicated in below brackets. (1) Prepare the Transmitter to pass through the valve hole which is positioned on the steel, aluminum or aluminum alloy wheel rim.
(4) Attach the Washer that is the spare part of Transmitter from the outside of the wheel rim onto the valve hole. (5) Attach the Core that is the spare part of Transmitter from the outside of the wheel rim onto the valve hole. ( => Recommendatory Torque to attach the Core: 2~3.2 Kgf.cm ) (6) Attach the Nut that is the spare part of the Transmitter from the outside of the wheel rim onto the valve hole. ( => Recommendatory Torque to attach the Nut: 35~45 Kgf.
(7) Install the external antenna into the transmitter valve as the following pictures. (8) Finalize the installation of the Transmitter. 5.2.2 De-Mounting Tire with Transmitter Inside Please demount the product with standard demounting equipment, and demounting procedures could be proceeded by the technicians from our appointed vehicle manufacturer or garage.
6.2 Digital Receiver Button Function Description (1) Button Temperature Display temperature of tires after press button 35C 36C (2) . 35C 36C ↓ (Downward In “General Set Up Mode”, acts as downward button to Button) select function and number. (3) Counter-clockwise In “Special Set Up Mode”, acts as counterclockwise Button button to select tire for programming. (1) Pressure Button Display pressure of tires after pressing button .
7. Alarms and Warnings 7.1 Pressure Threshold Alarm and Warning a. 9.1.1 Tire pressure lower than Manual Should Programming Manual Pressure Threshold Setting： A Low Pressure Warning is initiated when the pressure drops below the programmed Pressure Threshold Setting Limit。 1. Warning Actions Include： 1st. LED Alarming Indicator blinks once。 2nd. An short audio alarm。 2. Suggested Action to Warning： Threshold Setting Limit are 25psi and 75℃ respectively while factory-preset value are 23psi and 85℃： 1.
7.2 Temperature Threshold Alarm and Warning 7.2.1 Tire Temperature higher than Manual Temperature Threshold Setting： A High Temperature Warning is initiated when tire Temperature rises above the programmed Temperature Threshold Setting Limit。 1. Warning Actions Include: Should Programming Manual Threshold Setting Limit are 25psi and 75℃ respectively while factory-preset value are 23psi and 85℃： Indicator 1.LCD Display will remain normal when measured temperature is blinks once。 between 76℃ to 84℃。 2nd.
1. Press button for more than 2 2. second to go into “General Set Up Mode”。 Use button (act as downward button) and button (act as upward button) to select “Pressure Warning “ setting。 3. LCD Display will show： Use button (act as downward button) and (act as upward button) to select a number as Pressure Threshold。 4. Low Pressure Warning 26 PSI 5. Press value。 button to conform setup 6. Press button again “General Set Up Mode”。 to exit 8.1.2 Manual High Pressure Threshold Setting 1.
8.3 Reset：(Reset pressure and temperature to zero. Furthermore. proceed this procedure can cancel alarm status temporarily.) (1) Press button for more than 0.5 (2) Use button (acts as downward second to go into “General Set Up button) and button (acts as upward Mode”. button) to select “Reset” setting. Reset (3) Press button to confirm. (4) All previous pressure and temperature figures will be reset to zero. ok 8.
1st. This setting is in effect after the Transmitters have been stationary for longer than 10 minutes and the vehicle has been accelerated up to the speed of 6 mph (10 kph) to 12 mph (20 kph)。 2nd. Transmitter ID Input Via “Search Tx” setting for Digital Receiver Module Replacement is only valid for all the transmitters have never been rotated before。 1. button for more than 2 2.
9. Special Set Up Mode 9.1 Tire Exchange Mode 9.1.1 Enter into “Special Set Up Mode” 1. Simultaneously press and button 2. for more than 2 seconds to enter “Special Set Up Mode”。 Use button (act as downward button) and button (act as upward button) to select ”Exchange Location” setting。 3. The LCD Display will show： Press button to accept this special function setting。 4. Exchange Location 5. Press will EXIT “Special Set Up Mode”。 9.1.
9.3 Transmitter ID Change Mode Note: (1) This Mode is used for Transmitter replacement and the new Transmitter ID need to be inputted. (2) Whenever Transmitter/s is/are out of order and call/s for replacement, the defective one/s has to be specified its original color of text on label or its original paired Valve Tag color to ensure the new one/s for replacement is/are of the same color of original one/s, and which with the rest of original Transmitters constitute a set.
9.4 Set Pressure Unit Mode 1. button Simultaneously press and 2. for more than 3 seconds to enter “Special Set Up Mode”。 3. The LCD Display will show： 4. Press button to accept this special function setting。 PSI Use button (act as downward 6. button) and button (act as upward button) to select psi,kPa,Bar unit. Press button to accept this unit setting.or Press will EXIT “Set Pressure Unit” Set Pre Unit 5. 9.5 1. 3. Set Temperature Unit Mode Simultaneously press and button 2.
5. Use button (act as counterclockwise button (act as button) and clockwise button) to move →cursor to mark Display Wheel Location button to cancel or set ＊ Press signal。 →01* 03 6. will comfirm and come back Press “Special Set Up Mode”。 02* 04 9.7 Exit Special Set Up Mode Press button again；LCD Display will back to initial screen。 32 32 32 32 Note：Value shown is for reference only. 10.
10.2 This Limited Warranty Provided by Mobiletron Does Not Cover (1) Product that have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not authorized by Mobiletron. (2) Damage that occurs in shipment or due to act of God. 11. Things to Notice 11.
13. Technical Specifications 13.1 Transmitter (1) Operation Condition Description Pressure Range Rated Pressure Value 0 ~ 45 90 -20 ~ +125 -4 ~ +257 0 ~ 100 Operating Temperature Operating Humidity (2) Radio Frequency Transmitter Description Central Frequency (3) Special Specification Description Value Units 433.
14. Tire Rotation Table Update this Table whenever Tire is Rotated or Transmitter/s is Replaced to ensure Transmitter ID data in the Digital Receiver indicating the correct tire.
1. The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
