Product Manual

ManualsBrandsMobile Technologies ManualsElectronicsMerchandise Theft Deterrent System

CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL

Product Manual for

CX FLEX™ Single Alarm Only

DO NOT REMOVE FROM STORE

Contents

1. Installation 2

2. Key Whitelist 3

3. Merchandising 3

4. Managing Alarms 4

5. Cable Removal 4

6. Remerchandising 4

7. Adding New User Keys 5

8. Deleting Whitelist 5

9. Battery Replacement 6

10. Position Removal 6

11. LED Status Indicators 7

12. Dimensions 8

13. FCC and ISED Statement 9

For additional support, please reach out to our

Contact Center at 800-426-6844

CONTENTS

Summary of content (9 pages)

PAGE 1
CONTENTS CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL Product Manual for CX FLEX™ Single Alarm Only Contents 1. Installation 2 2. Key Whitelist 3 3. Merchandising 3 4. Managing Alarms 4 5. Cable Removal 4 6. Remerchandising 4 7. Adding New User Keys 5 8. Deleting Whitelist 5 9. Battery Replacement 6 10. Position Removal 6 11. LED Status Indicators 7 12. Dimensions 8 13.
PAGE 2
INSTALLATION CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL 1 If needed, clean the underside surface with an alcohol pad and allow to dry. Place new VHB on the puck. 2 Clean the desired surface with an alcohol pad allow it to completely dry. Peel the red film from the VHB adhesive. 3 Press down on the base plate for 10 seconds for full VHB contact. Allow 24 hours for full VHB adhesion. www.mtigs.com | T:800.426.
PAGE 3
KEY WHITELIST CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL 1 Place Authorization Card over the RFID icon to register to system. 2 Place the User Key you want to add over the RFID icon. If successful  unit beeps 2 times Repeat process for all User Keys until they are successfully added. 3 To close the whitelist mode, place the Authorization Card over the RFID icon. Whitelist mode will end automatically after 3 minutes of no use. System must be disarmed to perform this operation.
PAGE 4
MANAGING ALARMS CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL 1 To silence an alarm, hold the user card over the RFID icon. To disarm after silencing an alarm, hold the user card over the RFID icon for 5 seconds. CABLE REMOVAL 1 Insert a corner of the RFID card into the slot and press down until the cable ddetaches. 2 Remove the cable. REMERCHANDISING 1 From an armed state, place the user key over the RFID icon to disarm the system. LED will be flashing red (2 short flashes every 10 seconds).
PAGE 5
ADDING NEW USER KEYS CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL 1 From an armed state, place the user key over the RFID icon to disarm the system. LED will be flashing red. 2 Place Authorization Card over the RFID icon. Follow Key Whitelist process starting on page 3. DELETING WHITELIST (This will delete all User Keys from the system.) 1 From an Armed state, place the User Key over the RFID icon to disarm the system. LED will be flashing red. www.mtigs.com | T:800.426.
PAGE 6
BATTERY REPLACEMENT 1 CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL 2 3 Use CR2450 Batteries ONLY. CAUTION: Risk of explosion if the battery is replaced by an incorrect type. POSITION REMOVAL 1 www.mtigs.com | T:800.426.
PAGE 7
LED STATUS INDICATORS Visual Reference CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL System Status Condition 1. Factory Reset LED is OFF. 2. No product merchandised or not properly merchandised 3. Armed 4. Battery needs to be replaced Solution 1. No User or Authorization cards are registered, LEDs will not flash when properly merchandised, system will not arm -- Create Whitelist per Page 3. 2. Check connections for proper merchandising. 3. System is armed. 4.
PAGE 8
DIMENSIONS CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL 2.36” 1.09” 1.87” www.mtigs.com | T:800.426.
PAGE 9
FCC AND ISED STATEMENT CX FLEX™ SINGLE ALARM ONLY PRODUCT MANUAL FCC ID: 2AA2X-15000221 Model: CX Flex 1A FCC Statement This device complies with Part 15 of the FCC Rules. Caution: If any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.