Instruction manual

ACU-1000 Operations Manual
8-2
Configuration Page, 2-72
Configuration Programming via Browser, 2-69
Connection Management Page, 2-76
Information Page, 2-71
Manual Page, 2-78
Restoring Factory Defaults, 2-78
Software Update, 2-80
DSP-1, 1-4
DSP-1 and RDI-1 Programming
Audio Muted When Squelched, 2-97
Auxiliary Output Control, 2-100
COR Inhibit Time After PTT, 2-98
COR Polarity, 2-91
COR Sampling, 2-96
COR Type, VOX/VMR Threshold, Hangtime,
and Audio Delay, 2-93
DTMF Command Enable, 2-99
DTMF Mute Timer, 2-91
DTMF Pre-emphasis, 2-99
Full/Half Duplex, 2-91
High Frequency Equalizer, 2-99
Module Security Level Selection, 2-99
Noise Reduction Value, 2-97
PTT or COR Priority, 2-98
Receive Level, 2-90
Transmit Keying Tones/Keying Tone Amplitude,
2-97
Transmit Level, 2-90
Voice Prompt Initiation Delay, 2-100
DSP-1 and RDI-1 Programming Items, 2-90
DSP-1 Programming Item, 2-87, 2-88
DSP-2
Block Diagram, 5-15
Block Diagram Description, 5-6
General Description, 5-6
DSP-2 Jumper Settings, 2-43
DSP-2 Module
Technical Information, 5-6
DSP-2 Module Connections, 2-15
DSP-2 Replaces the RDI-1 Module, 7-21
DSP-2 Specifications, 5-8
Enable PIN Security, 3-15
Equipment and Accessories Supplied, 1-21
Exclusive Operation Mode, 3-15
Expansion Connector, 2-17
Expansion Connector- P14, 2-17
External Interconnect Information, 2-12
False Keying, 4-1, 4-6
Fault LEDs (HSP-2, DSP-1, RDI-1, PSTN-2, LP-
2), 3-6
Front Panel Controls and Indicators, 3-5
Full-Duplex, 1-6
General
Operation, 3-1
General Description
Technical Information, 5-1
General Information
ACU-1000, 1-1
Glossary, 9
COR, 9
COS, 9
CPM-2, 9
CTCSS, 9
D
TMF, 9
Extension, 9
Hangtime, 9
HSP-2, 9
LP-2, 9
Slot, 10
SNR, 10
Squelch, 10
VMR, 10
VOX, 10
Half Duplex, 1-6
Hardware Configuration Settings, 2-38
Headphones Output Jack (HSP-2), 3-6
High Frequency Equalization Procedure, 4-13
How PIN Security Works, 3-14
How to Delete PIN Numbers from the Database, 3-
16
How to Enable PIN Security, 3-15
How to Input PIN Numbers into the ACU-1000
Database, 3-15
How to Set ACU-1000 Extension Security Levels,
3-15
HSP-2, 1-3
Block Diagram Description, 5-2
Functions and Operation, 3-7
General Description, 5-2
HSP-2 Module Connections, 2-14
HSP-2 Operational Command Items, 3-8
HSP-2 Programming Items, 2-90
Voice Prompt Initiation Delay, 2-90
HSP-2 Specifications, 5-5
Technical Information, 5-5
HSP-2A
Block Diagram, 5-13
HSP-2A replaces HSP-2, 7-14
Inability Of Dispatcher To Gain System Control, 4-
1
Input PIN Numbers into the ACU-1000 Database,
3-15
Installation, 2-1
Installation Checklist, 2-12
Installation Considerations, 2-3
Installation Overview, 2-2
Interface & Optimization, 2-18
Interface Cables, 2-18
Interface Module Operational Commands, 3-11
Interoperability, 1-1
ACU-1000,
1-2
Modules, 1-3