User's Manual

192.168.188.1
192. 168.1 88.1
192 .168. 188.1
192.168.188.1
How to enter management interfaceHow to install the battery
Answers to common questions
Device button description
FAQ 1: Forgot username and password how to do? (How to reset the
router?).
If you forget the username and password, or you can't do the
backstage in the setup process, when the router is energized, press
router's RESET key for 5-8 seconds and release, router make factory
default.
FAQ 2: Can’t find router’s wifi signal?
The computer connects to the LAN port through the network cable,
login in router management interface "Lan settings", wireless function
enable / disable, confirms that this option is enabled. If you do not
have a computer, you can reset the router. For details, see FAQ1.
FAQ 3: Enter 192.168.188.1 in the browser's address bar, can’t open
management page?
1: If the computer is set up, open the IE browser, click the tool - click
the Internet option, click the connection - click the LAN settings to
ensure that the proxy server does not tick.
2: If the computer is set up, please check the computer's wireless
network configuration or local network configuration to ensure that the
computer "automatically gets the IP address", "automatically gets the
DNS server address", restarts the router, disconnects the router
power, and then plug in the power supply later.
3: If you cannot login to the router management interface after
completing the above operations, it is recommended that you reset
the router and reset method see FAQ1.
FAQ 4: The router signal lights up, has data transmission, but the
Internet is slow.
1: Please move the router to other locations, such as near the
window, to ensure better reception of 4G signals.
2: Repower the router to reboot the router
FAQ 5: When the router changes the card during its operation, why
can't the device read the SIM card?
SIM card hot plug is not supported by equipment, and the insertion
and removal actions should be carried out under power failure.
Please disconnect the power of the router and then plug in the
power.
FAQ 6: Why can't you find pages when using mobile terminal
settings?
Some phones may be able to intelligently detect whether the
connected WIFI can access the Internet and may be disconnected
during settings. You only need to look at the WIFI you are now
connected to. If the connection is not the WIFI that the device
launches, you only need to reconnect and refresh the page.
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
1: Use the cell phone to connect the default
WIFI signal transmitted by the router. See
step 3 of insert and connection mode by
using the router WiFi signal.
1: Remove the battery cover.
2: Take out the connector of battery compartment then connect to
the battery.
3: Put the battery in the battery compartment and close the cover.
Note: After the battery is connected, the battery indicator on the
front of the device will display battery power. When the power
adapter is not powered on, the battery power is used. The
charging method of the battery is as follows: it starts to be
charged, when DC power adapter is plugged , and stop charging
after full charge.
2: Scanning two-dimensional code, using
mobile browser to open links or manually
enter 192.168.188.1 in the browser address
bar to enter management backstage.
3: In the background login page, enter the default account admin
and password admin to enter the router management backstage
interface.
Warm tips, you can use the computer to set up 1: Set up a computer
to automatically get IP 2: Computer network interface connecting
router LAN port 3: The address bar of the computer browser is
entered into 192.168.188.1, opens the router management
interface, and enters the default account and password to set it up. If
you are not familiar with computer, use cell phone to set it up.
SIM slot
DC input
WAN port
LAN port
Reset
Label
SIM slot
SMASMA
Wifi on/off
WPS button
Power on/off
WPS WLAN
1 2
3