User manual Mobeye® i110 SW version 5.
Table of content 1. 1.1 1.2 1.3 1.4 2. 2.1 2.2 3. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 4. 4.1 4.2 4.3 4.4 4.5 4.6 5. 6.
Attention! Very important This user manual contains important guidelines for the installation and usage of the Mobeye® i110. Please read these thoroughly before you start using the Mobeye®! In case of damage caused by disregarding the guidelines, the warranty expires. The user must regularly check the proper functioning of the Mobeye®. The manufacturer cannot be held liable for any damage caused by any incorrect use or incorrect functioning of the Mobeye®.
Introduction The Mobeye® is an easy to install alarm system that will notify you in case of a detection using the built-in GSM. To use the Mobeye® you will need a SIM-card of any provider. Typical applications are the security of places without any power supply or the temporary security of objects. The Mobeye® has the following features. Alarm notifications after movement detection In case of the detection of an intruder, the Mobeye® will send an SMS text message to your phone(s).
1. TO GET READY IN FOUR STEPS To get started with the Mobeye® only four steps are needed. 1. Place the SIM card in the Mobeye®. Make sure this SIM card is not secured by a PIN code. 2. Place the four batteries. 3. Enter at least one phone number in the Mobeye®. 4. Check the settings In this chapter these steps are explained. 1.1 STEP 1: SIM CARD To use the Mobeye® a SIM card of any provider is needed. On this SIM card, the PIN code security needs to be disabled.
2. SWITCHING THE MOTION DETECTOR ON/OFF 2.1 SWITCHING ON To activate the Mobeye® motion detector with your personal user code. Enter your user code Press “OK” The light turns red shortly and an indication tone is started. This repetitive tone will last during the exit delay of 60 seconds. As soon as the acoustic signal stops, the Mobeye® is active. In case the user code is entered incorrectly 3 times, the indicator turns red and the Mobeye® will be blocked during 10 minutes. 2.
3. MOBEYE SETTINGS The Mobeye® settings can be added via the keypad and SMS text messages. First the method of programming is discussed, next the explanation of the settings. 3.1 CONFIGURATION To change the settings, please follow the instructions: Enter your 4-digit personal code Press “menu” -> light turns green Enter the menu number belonging to the setting to be changed. Press “OK” Enter the new setting Press “OK”.
The Mobeye® first prepares the programming mode. The light flashes red (interval ca. 1 sec). As soon as the light turns green, the Mobeye® is able to receive SMS-messages. In order to program the extra message text, send an SMS in following structure: .name.xxxxxx. Please regard the dots between and behind the commands, command ‘name’ in small letters! Example: enter the text ‘boat evergreen’ (e.g. user code 1111) 1111 .name.boat evergreen.
3.6 THE SENSOR SENSITIVITY The detectors’ sensitivity can be changed to a high or low(er) value. 1= High 2 = Low In the high sensitivity mode each detection will provoke an alarm. In the lower sensitivity mode the alarm will be provoked in case two detections are measured within a time frame of 15 seconds. This mode prevents false alarms in case of e.g. draught and is most suitable in case the sensor is directed towards an open space. 3.7 ENTRY DELAY It is possible to choose from 4 entry delay times.
4. ADVANCED OPTIONS 4.1 REQUEST SETTINGS The settings can be sent to the set telephone number as SMS text message. In this way you also check the correct working of the SIM card. Enter your 4 digit user code (factory setting: “1111”) Press “menu” Enter “10” Press “OK” Within ca. 30 seconds the set phone number will receive the list with settings. 4.2 RESET TO FACTORY SETTINGS It is possible to reset the Mobeye® to factory settings.
The Mobeye® now switches on the GSM modules and searches for all present networks. It also checks the network strength of the SIM card provider in the device. As soon as the GSM network is found, the light will turn green.
5. ISSUE SOLVING Error Possible reason Solution Mobeye® cannot be switched on. You hear an error tone, the red light is turned on shortly. The light is flashing during switching on. No valid Telephone number was entered. Enter a valid number. No valid SIM card was entered or the SIM card was not made pin code free. Mobeye is activated. Check the SIM card. No network is available, belonging to the SIM cards provider. You entered a false user code three times. Telephone number is not correct.
Declaration of Conformity Herewith we, Mobeye, declare that the product Mobeye i-110 is in compliance with the essential requirements of the following European standards / EU Directives: Directive 73/23/EEC (low voltage directive) Directive IEC/EN 50130 Electromagnetic compatibility Directive 1995/5/EC R&TTE (Radio & Telecommunications Terminal Equipment) The conformity with the essential requirements of 1995/5/EC has been verified against: ETSI EN 301 489-1 V1.5.1 ETSI EN 301 489-7 V1.2.
