User's Manual

Specifications
71.35*75.65*127.15mm
10mm
15W/10W/7.5W/5W
ABS+Tempered Glass/Leather
Input
Output
80%
Product Standard
Product Dimension
Product Material
Charging Distance
Charging Efficiency
Qi
DC 12V/1.5A,9V/1.67A,5V/2A
AC-10 15W用户手册（产品说明书）
15W Fast Wireless Car Charger
User Manual
Fast wireless charging requires QC2.0/3.0 quick car charger.
Product Features
Product Parts Description 1
Product Parts Description 2
Product Operating Guide
Attention
1.Please do not vigorously extrude or collide.
2.Please do not dismantle or put it into fire or water when the
product is power on,to avoid short circuit or leakage.
3.Please do not use it in severely high temperature,high humidity
or corrosive environment,to avoid damage to the circuit leakage.
4.Please do not put the magnetic strip or chip card (Such as ID
card,bankcard etc.)on the charging pad to avoid to cause
magneticcard lose efficacy.
5.Please do not put the metal (Such as coin etc.) on the charging
pad when charging,to avoid damage from heating.
尺寸：350*100mm 单面印刷
材质：157克铜版纸
1. Top backside touch button,touch to open and easy for one hand
operation. Charging indicator on both sides, and the small square
LED indicator in the middle indicates the center position of the
internal coil.
2. Built-in wireless charging transmitter coil, the two arms and
feet will automatic closing when put the phone on the charger,
The transmitter coil automatically starts to find the mobile phone
charging coil, and the mobile phone starts wireless charging after
coil precise alignment.
3. Suitable for different size phones,anti-slip silicone on both arms
and feet,Type-C charging port.
4. Built-in stepper motor, it works with low noise.
5. NPO capacitors,lower charging temperature and high charging
efficiency.
6. Standby mode: the green and blue LED indicator light flashes
alternatively,then the green indicator light keeps on.
7. Charging mode: the blue LED indicator light keeps on,the light
turns to green if remove the receiver.
8. FOD function: when put metal or magnet objects on the charger,
the blue and green LED indicator light will flash for reminding.
9. Perfect protective function based on over-voltage, over-current,
over-temperature and short-circuit protection.
1. Please make sure the product connect to the power before using.
2. The green LED indicator light on if connected with power.
3. The LED indicator light will flashes and the product stop charging
when the current is too large or there is foreign object. Do not
wireless charging the phone if similar situation happened.
4. Please touch the backside power button to open the two arms,
the wireless charging start and the two arms/feet will closing
automatically once you put the phone on the charger. Only need
to touch the power button again to release two arms and easily
remove the phone.
5. Please purchase the wireless receiver module or case separately
(Not included in the product) if your phone do not support
wireless charging.
Charging Head
Angle Pivot Knob
Vent Clip
Type-C Charging Port
Indicator Light
(two sides)
Touch Button
Adjustable Side Arms
Adjustable Feet
Lever
Telescopic Knob
Suction Cup
Pivot Knob
Telescopic
Support Pole
Silicone Mat
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. During the operation of device a
distance of 15 cm surrounding the device and 20 cm above the top
surface of the device must be respected.
FCC ID：2A2MY-AC-10.