EN Instruction Manual mo.hub V1.
Thank you very much for purchasing a high quality motogadget product - Made in Germany. Please read the following information and recommendations thoroughly and follow these instructions during installation and use of the instrument. No liability shall be assumed by motogadget for damage or defects resulting from negligence or failure to follow the operating and contact: motogadget GmbH Koepenicker Str. 145 D - 10997 Berlin Tel. +49 (0)30-6900410-0 www.motogadget.de info@motogadget.
1 Review of Delivery All products from motogadget are thoroughly checked to ensure they are completely fault-free when dispatched. Please check the received goods immediately for possible transport damage. If you find any damage or other deficiencies, please contact us immediately. In this regard, we refer to our General Terms of Business and Delivery, which are published at www.motogadget.com.
DEVICE HOUSINGS AND ALL OTHER DELIVERED PARTS MUST NOT BE OPENED OR DISMANTLED. IN CASE OF NON-COMPLIANCE, ALL WARRANTY CLAIMS BECOMES INVALID. THE USE OF THE DELIVERED DEVICE AND ITS ACCESSORIES FOR RACING OR OTHER COMPETITIONS AS WELL AS FOR ANY USE NOT CORRESPONDING TO THE RECOMMENDED APPLICATION ALL WARRANTY CLAIMS SHALL BE INVALID. 3 Safety Instructions • THE VEHICLE BATTERY MUST BE COMPLETELY DISCONNECTED PRIOR TO ANY WORK ON THE VEHICLE’S ELECTRICAL SYSTEM.
4 Application The mo.hub is a universal data interface between vehicle and motogadget instrument or smartphone. Compatible vehicles with BUS or OBD interface are connected to the mo.hub by a supplied vehicle-mounted plug (Plug & Ride). For vehicles without interfaces, the required signals (tachometer, speed, control lights, etc.) must be tapped individually and connected to the mo.hub. The configuration of the mo.hubs is done by our app m.ride.
5 Overview area of Bluetooth Antennado not cover with metal terminal marking Status LED mouning holes for cable cover serial no.
6 Mounting the cable cover & cable guide M3x16 countersunk cable ties
7 Mounting options cable ties M4 screws
8. Connecting motogadget instruments to the mo.hub 8.1 motoscope mini and combi-frame or handle bar clamp mo.hub motoscope mini combi-frame Port Nr.
8.2 motoscope tiny und motoscope classic mo.hub motoscope tiny motoscope classic Port Nr.
9 Connecting the vehicle to the mo.hub 9.1 vehicles without data BUS mo.hub Port Nr.
9.2 BMW modells with LIN Bus 9.2.1 Fahrzeugtyp Identifizierung BMW models from 2015 with a 6 pin instrument plug with dimensions of approx. 9x10x22mm, are equipped with a LIN bus for communication between control unit and instrument. 9.2.2 Connecting the vehicle-specific plug and the battery cable to the mo.hub mo.hub motogadget BMW LIN Fahrzeugstecker Port Nr.
8) Insert the plug of the OEM speedometer (not tachometer!) In the with motogadget Insert vehicle plug. The second OEM instrument plug (if available) with Protect heat shrink tubing from splash water. 9) The eyelet of the motogadget battery connection cable with the battery-plus connection terminal connect 10) Connect the battery (first plus, then minus) 11) Install the tank and seat 9.3 BMW Modells with CAN Bus 9.3.
9.3.3 Installation 1) Jack up the vehicle, remove seat and tank 2) Unscrew OEM instrument, unplug connector, unscrew OEM instrument carrier. 3) attach the motogadget instrument to the vehicle-specific motogadget retaining plate and connect the tail cable of the motogadget instrument to mo.hub 4) Connect motogadget vehicle-specific plug and battery cable to mo.hub 5) Screw the motogadget retaining plate with instrument to the fork bridge with the OEM screws. 6) Attach mo.
11 Return and Complaint Before sending your mo.hub to us for technical review, please contact Technical Support. Visit our website and follow the instructions under “Support”. For support requests, we always need the serial number (sticker top mo.hub, your smartphone model used, the app version (see main menu under “About”).) To return the item, please follow the instructions under “Service” on our website.
Regulations PRODUCT INFORMATION: Manufacturer: motogadget GmbH Model: mo.unit blue FCC ID: 2AIF8-4005000 IC: 21495-4005000 FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
