www.mkdiamond.com MK-101 Pro24 JCS OWNER'S MANUAL OPERATING INSTRUCTIONS U.S. Patent No. 7,419,538 Revision 201 06.2013 Manual Part #162059 Caution: Read all safety and operating instructions before using this equipment. This parts list MUST accompany the equipment at all times.
INTRODUCTION Congratulations on your purchase of a MK-101 Pro24 JCS. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest construction power tools and diamond blades in the industry. Operated correctly, your MK-101 Pro24 JCS should provide you with years of service. In order to help you, we have included this manual. This owners manual contains information necessary to operate and maintain your MK-101 Pro24 JCS safely and correctly.
TABLE OF CONTENTS SAFETY Safety Messages Damage Prevention Message General Safety Precautions and Hazard Symbols California Proposition 65 Message Electrical Requirement & Grounding Instructions Electric Motor Safety Safety Label Locations Lockout Product Specifications 4 4 4-7 8 9-10 11 12 12 13 UNPACKING, TRANSPORT and ASSEMBLY Unpacking Contents Transport JCS Stand Setup Assembly 14 14 15 16-18 19-21 SETUP, OPERATION and SHUTDOWN Setup Operation Adjustment Cleanup 22-23 24-28 29-30 31 MAINTENANCE A
MK-101 Pro24 JCS SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. Safety warnings and guidelines do not by themselves eliminate danger. They are not substitutes for proper accident prevention procedures and good judgement.
MK-101 Pro24 JCS SAFETY KEEP CHILDREN AWAY All visitors and children should be kept a safe distance from work area. MAKE THE WORKSHOP KID PROOF Make the workshops kid proof by using padlocks, master switches or by removing starter keys. DO NOT FORCE THE TOOL A power tool will do a job better and safer operating at the rate for which it was designed. USE THE RIGHT TOOL DO NOT force a tool or an attachment, to do a job that it was not designed to do.
MK-101 Pro24 JCS SAFETY USE RECOMMENDED ACCESSORIES Consult the owner’s manual for recommended accessories. Using improper accessories may increase the risk of personal or by-stander injury. Unauthorized equipment modifications will void all warranties. Manufacturer does not assume responsibility for any accident due to equipment modifications. Always ensure that the machine is on level ground before using.
MK-101 Pro24 JCS SAFETY WARNING Diamond Blades improperly used are dangerous. Comply with American National Standards Institute Safety Code, B7.1 and, Occupational Safety and Health Act covering Speed, Safety Guards, Flanges, Mounting Procedures, General Operating Rules, Handling, Storage and General Machine Conditions ELECTRICAL SHOCK NEVER touch electrical wires or components while the engine is running.
MK-101 Pro24 JCS SAFETY SILICA DUST WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
MK-101 Pro24 JCS SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! WARNING In case of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
MK-101 Pro24 JCS SAFETY WARNING The “drip loop” is that part of the cord below the level of the receptacle, or the connector, if an extension cord is used. This method of positioning the cord prevents the travel of water along the power cord and coming in contact with the receptacle. If the plug or receptacle gets wet, DO NOT unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the tool. Then unplug and examine for presence of water in the receptacle.
MK-101 Pro24 JCS SAFETY ELECTRIC MOTOR SAFETY (( For maintenance care and operation of the electric motor, refer to your electric motor instruction booklet furnished with the electric motor. Protect the electric motor from dust as much as possible and keep ON )) ventilating openings clean. Before plugging in the machine, make sure that the outlet voltage is within the voltage marked on the machines's data plate. CAUTION DO NOT spray water on the electric motor. Do not touch the plug with wet hands.
MK-101 Pro24 JCS SAFETY SAFETY LABEL LOCATIONS The warning labels contain important safety information. Please read the information contained on each safety label. These labels are considered a permanent part of your saw. If a label comes off or becomes hard to read, contact MK Diamond or your dealer for a replacement. Tile Saws ! CAUTION Receptacle is for water pump only. 125V, .6 amps max. Label A ! CAUTION This saw is to be used with a Ground Fault Circuit Interrupter.
MK-101 Pro24 JCS SAFETY PRODUCT SPECIFICATIONS • • • • • • • • • • • • • • • • • Integrated stand allows operator to set up or transport in a matter of seconds Solid rubber heavy-duty wheels won't scuff floors Designed for easy transport, loading and storage by one person Integrated gas shocks help handle the weight of the saw during setup and breakdown Wheel latches prevents stand from moving during operation Fully enclosed high torque, fan-cooled motor Permanently lubricated, dual-sealed, heavy-duty bl
MK-101 Pro24 JCS SAFETY UNPACKING Your saw has been shipped from the factory thoroughly inspected. Only minimal assembly is required. CAUTION Use proper lifting techniques when lifting the Saw.
MK-101 Pro24 JCS TRANSPORT TRANSPORT he MK-101 weighs approximately two hundred and two (202) pounds. CAUTION 1. T 2. N ever transport the MK-101 with water in the Water Basin. Lift the saw using the handle.
MK-101 Pro24 JCS STAND SET-UP JCS STAND: Key Components for Set Up NOTE: Familiarize with the following components before proceeding to SET UP.
MK-101 Pro24 JCS STAND SET-UP JCS STAND: Key Components for Set Up CAUTION THE MK-101 w/JCS stand weighs approximately two hundred and two pounds (202 pds). Read and understand all instructions. Failure to follow all instructions in SEQUENCE could result in serious injury. (A) Pull, turn & release pin to lock Wheel. (B) Stand on left side of saw. Pull Blue Knob and pull Front Legs out slowly. (C) Pull legs until they are locked by Red Leg Lock.
MK-101 Pro24 JCS STAND TAKE-DOWN JCS STAND - Take Down Instructions (A) Move table forward toward operator. (B) Pull and hold Green Knob. Lift Safety Arm until it hits bottom of Frame. (C) Release Green Knob to secure Safety Arm. (D) Move Table back and ensure table is secure. (E) Push down on Cutting Head Handle to collapse the saw. (F) Tilt Saw backwards to upright position. (G) Hold up Front Legs, flip and hold Red Leg Lock to unlock Front Legs.
MK-101 Pro24 JCS ASSEMBLY ASSEMBLY Follow the assembly instructions to prepare your MK-101 for operation. Cutting Head Installation NOTE: If the cutting head is installed, go to the next step. (A) Align Cutting Head rear Pivot Hole to the Post Pivot Shaft and slide onto shaft. (D) For maximum cutting length, the Cutting Head should be in the front pivot hole and the Post should be in the rear post retaining hole. (B) Ensure Cutting Head stop is in upward position.
MK-101 Pro24 JCS ASSEMBLY DIAMOND BLADE INSTALLATION NOTE: When installing the Retaining Screw, do not “cross-thread” and DO NOT over tighten the screw. Shaft Lock Pushbutton (A) Position Movable Cutting Table to the front of the saw and raise the Blade Guard by loosening the wingnut. (D) Install Diamond Blade onto Blade Shaft. (B) Locate the Shaft Lock push button on the underside of the Cutting Head.
MK-101 Pro24 JCS ASSEMBLY ADJUSTABLE CUTTING GUIDE INSTALLATION NOTE: The Adjustable Cutting Guide can be used on either side of the Diamond Blade. (A) Place the Adjustable Cutting Guide onto the Movable Cutting Table Ruler/Stop and tighten the retaining thumbscrew. SPLASH GUARD INSTALLATION (A) Install the retaining thumbscrew through the washer and Splash Guard then align to the hole found on back of the Blade Guard. (B) Install the Splash Guard onto the Blade Guard.
MK-101 Pro24 JCS SETUP SETUP Pre-start Inspection Prior to beginning work, a pre-start inspection of the saw should be performed. (A) Ensure the ON/OFF Switch is in the OFF position. (B) Verify the Movable Cutting Table moves freely. (C) Inspect the Diamond Blade for damage – verify the blade is correct for the material being cut. Inspect for damage (D) Inspect the Pump Assembly for damage – ensure the cord is free of cracks or cuts.
MK-101 Pro24 JCS SETUP WATER PUMP SETUP FOR OPERATION The Water Pump can be setup for operation in two ways, External Water Source or Re-circulation. NOTE: If using a dry blade for operation, DO NOT connect the water pump. External Water Source This is the preferred method of cooling. (A) Remove the Drain Plug. Place empty container under hole for water drainage. Re-circulation NOTE: (B) Place the Water Pump in an external container and fill until water completely covers the Water Pump suction.
MK-101 Pro24 JCS OPERATION MK-101 PRO Series Setup for Operation CAUTION 1. B efore powering or starting, check for damage that could prevent this equipment from proper operation or performing it’s intended function. Check for binding and alignment of moving parts. Check for damaged, broken, or missing parts. 2. Verify the On/Off switch is in the OFF position. 3.
MK-101 Pro24 JCS OPERATION Set Cutting Depth CAUTION When loosing the Cutting Head Adjusting Knob, the Cutting Head will pivot down unless held. (A) Loosen Cutting Head Adjusting Knob. (B) Set cutting depth approximately 1/4 to 1/2 inch below the surface of the Movable Cutting Table. (C) Tighten the Adjusting Knob. *A GFCI wall socket is the preferred protective device. Cutting Straight Edges CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.
MK-101 Pro24 JCS OPERATION Diagonal Cutting NOTE: CAUTION To cut diagonal, the Dual 45º Flat Angle Guide (MK Diamond Part No. 134557-MK) should be used. DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. (A) Remove the Adjustable Cutting Guide. (B) Position the Dual 45º Flat Angle Guide and tighten the retaining thumbscrew. (D) Verify proper cooling flow on both sides of the blade (See Maintenance Section to increase/decrease flow). (E) Perform the cut.
MK-101 Pro24 JCS OPERATION 45° Miter Cutting NOTE: CAUTION To cut 45° Miters, the 45° Bullnose Miter Guide (MK Diamond Part No. 153201MK) should be used. DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. (A) Position the 45º Bullnose Miter Guide and tighten the retaining thumbscrew. (B) Position the tile on the 45º Bullnose Miter Guide and the Ruler/Stop. Turn the motor ON. (D) Perform the cut. Turn the motor OFF when work is complete.
MK-101 Pro24 JCS OPERATION Off-angle Cutting NOTE: CAUTION To cut angles other than 45º angles or Miters, a 90º Protractor (MK Diamond Part No. 134569-MK) should be used. DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. (A) Place the 90º Protractor on the Ruler/Stop. (D) Position the tile against the 90º Protractor and the Ruler/Stop. Turn the motor ON. (B) Set the desired angle and tighten the thumbscrew.
MK-101 Pro24 JCS ADJUSTMENT Adjusting the Cutting Head NOTE: CAUTION For larger tiles and maximum cutting length, the cutting head should be in the front pivot hole. The Cutting Head is heavy! Care must be used when changing the position of the Cutting Head. (A) Ensure the ON/OFF Switch is in the OFF position. Unplug the GFCI from the power source. (B) Remove the Blade. Remove Adjusting Knob. (C) Remove the Cutting Head from the rear pivot hole. (D) Install the Cutting Head onto the front pivot hole.
MK-101 Pro24 JCS ADJUSTMENT Adjusting the Post for Maximum Cutting Length CAUTION The Cutting Head and Post are heavy! Use care when changing the position of the Cutting Head. (A) Ensure the ON/OFF Switch is in the OFF position. Unplug the GFCI from the power source. (B) Remove Water Basin. (C) Remove the Cutting Head (See Adjusting the Cutting Head. CAUTION Hold the Post when removing the Post Support Plate. (D) Loosen retaining bolts. (E) Remove the Standoffs and retaining bolts.
MK-101 Pro24 JCS CLEANUP Cleanup NOTE: 1. If an external water source was used, steps A through C may be skipped. 2. Dispose of waste water in accordance with applicable Federal, State and Local laws. (B) Place the Water Pump In an external container. (A) Clean the Water Pump suction of all debris. CAUTION Ensure the saw is disconnected before completing the remainder of the cleanup process. (D) Remove the Water Basin from the MK-101.
MK-101 Pro24 JCS MAINTENANCE NEW MAINTENANCE Perform the following after initial purchase and operation of the MK-101. (A) Check and adjust V-belt tension following first 48 hours of operation (See V-belt Inspection). Maintenance Following Use To extend the life of the MK-101 Pro24, the following procedure should be performed after each use. Lubricate all points listed below with light oils such as, 3 in 1, WD-40, etc. CAUTION Ensure the saw is off and disconnected before performing any maintenance.
MK-101 Pro24 JCS MAINTENANCE Monthly Maintenance The following maintenance should be performed Monthly. (A) Remove the Diamond Blade. (B) Lubricate the Outer Flange and Retaining-nut. (C) Lubricate the Arbor Shaft. (D) Verify the Roller Wheel Assembly is tight and in good condition. (E) Verify all motor mounting Bolts are tight. (F) Verify the Motor Adjustment Strap is tight. (G) Remove the Blade Guard. (H) Lubricate the Blade Guard Pivot Shaft.
MK-101 Pro24 JCS MAINTENANCE Flow Adjustment NOTE: If flow to the diamond blade requires adjustment, perform the following actions. (A) Increase cooling flow by releasing the Flow Adjusting Clamp. (B) Reduce cooling flow by Pressing down on the Flow Adjusting Clamp. Blade Dressing Like most cutting instruments, a diamond blade performs best when it is dressed. Over time and use, diamonds on the outer edge of the blade will become smoothed or “glazed” over.
MK-101 Pro24 JCS MAINTENANCE Diamond Blade change-out NOTE: When installing the Retaining Screw, do not “cross-thread” and DO NOT over tighten the screw. (A) Locate the Shaft Lock pushbutton on the underside of the Cutting Head. (B) Remove Retaining Nut and Outer Flange, depress and hold the Shaft Lock push button and loosen. (C) Remove the Diamond Blade. (D) Install the Diamond Blade onto Blade Shaft. (E) Verify the Blade is seated on the Blade Shaft and direction of rotation is correct.
MK-101 Pro24 JCS MAINTENANCE Belt Inspection, Adjustment and Replacement The MK-101 is designed with a power transmission belt. In order to ensure the MK-101 operates at peak efficiency, the belt should be inspected monthly, and changed if the belt shows damage and/or excessive wear. NOTE: 1. When a new belt is installed, it should be inspected and re-tensioned after the first forty-eight (48) hours of operation. (A) Remove the Diamond Blade.
MK-101 Pro24 JCS MAINTENANCE (J) Remove the belt. (K) Install the new belt (MK Diamond Part No. 158194). (L) Verify the belt is seated in the grooves of both pulleys. (M) Tighten the Motor Adjustment Strap to remove slack. (N) Check belt tension (proper tension 1/8-inch). (O) Repeat steps N and O until proper belt tension is achieved. (P) Tighten the motor mounting bolts. (Q) Install the Belt Guard. Tighten all three bolts.
MK-101 Pro24 JCS TROUBLESHOOTING Blade will not cut properly (A) Check for Smoothness or “Glazing” (Dress blade if needed). (B) Check for proper blade rotation. (D) Verify the blade is correct for the material being used. Movable Cutting Table Does Not Move Correctly (A) Check the Guide Bar and Frame for cleanliness – clean if dirty. (B) Check the Movable Cutting Table Roller Wheels for wear – replace if necessary. 38 (C) Ensure the Blade Core is not bent.
MK-101 Pro24 JCS TROUBLESHOOTING Cooling Flow (A) Verify the cooling flow Adjusting Clamp is open. If flow exists, go to Step A. (B) Remove the Cooling Transfer Tube from the Blade Guard inlet. Go to Step C. (C) Place Pump into a bucket of water and check flow. If flow exists, go to Step D. (D) Remove the Cooling Transfer Tube and check for flow. If flow exists, refer to water manual. (E) Remove the Blade Guard Intake Fitting. Go to Step J. (F) Remove the Cooling Channel cover screws.
MK-101 Pro24 JCS TROUBLESHOOTING Blade Stops Turning (A) Allow the motor to cool and depress motor Overload Reset Switch. If motor does not start, go to Step B. NOTE: (B) Verify all plugs fully installed. Check Ground Fault Circuit Interrupter Verify circuit breaker at least 20 amps - if not, move to 20-amp circuit. Verify circuit breaker is not tripped. If tripped, reset. Check power source voltage is 120V - if not 120V, move to another circuit.
MK-101 Pro24 JCS TROUBLESHOOTING Movable Cutting Table Misaligned The Movable Cutting Table of the MK-101 may become misaligned with the Cutting Head of the Tile Saw over time. Should misalignment occur, perform the following steps to realign the Tile Saw.
MK-101 Pro24 JCS TROUBLESHOOTING horizontal alignment procedure The Horizontal alignment will ensure that straight cuts (or Rip Cuts) are made. (A) Position Cutting Head to normal Cut Depth. (B) Move Guide Bar until Blade is centered in Cutting Groove. Tighten rear guide bar retaining bolt. (D) Position Square flat on Movable Cutting Table against Ruler/Stop. Position front of Square against Blade. (E) Move Guide Bar until Square rests evenly across Blade.
MK-101 Pro24 JCS TROUBLESHOOTING 90° alignment verification 90º-alignment verification ensures the blade cuts tile straight up and down and not at an angle. The Diamond blade must be removed and reinstalled when removing the blade guard. NOTE: If the blade is misaligned following 90º-alignment verification, return the saw to MK Diamond for repair. (A) Remove Blade Guard and water pan. (B) Position Square on Movable Cutting Table against the Diamond Blade.
20 5 25 15 23 17 11 21 32 18 5 34 6 26 19 8 30 10 24 31 22 4 9 13 2 1 16 35 7 33 28 29 14 27 3 27 27 12 27 MK-101 Pro24 JCS EXPLODED VIEW MK-101 Pro24 JCS Part # 153243-JCS 44
MK-101 Pro24 JCS Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 PARTS LIST Description Fitting, plastic, 1/4 FNPT x 1/4 BARB hose, vinyl, 1/4 x 3/8 Tsaw casting, acc dual flat-comp wrench, tilesaw, 15/16 csd end washer, flat, sae, 3/8 washer, lock, split, 3/8 pump, water 115v/60hz ul/csa screw, wing, 1/4 - 20 x 1/2 nut, hex, 1/4 - 20 washer, 1/4 sae flat washer, 1/4 split cock casting, acc bullnose lrg - comp pan, water plug, rbbr drain w/o hole screw,
MK-101 Pro24 JCS EXPLODED VIEW JCS Portable Stand Part # 169218 46
MK-101 Pro24 JCS Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 parts list Description WASHER, FLAT, SAE, 3/8 WASHER, FLAT, SAE, 5/16 NUT, 3/8 16 NYLOK HEX SCREW, 5/16 - 18 X 1 HEX HEAD MACHINE NUT, HEX, 8 -32 SCREW, 5/16 -1 8 X 2 HEX HEAD WHEEL, REAR 8" NUT, HEX, NYLK, 5/16 - 18 SCREW, HEX HD, 3/8 - 18 X 4 - 1/4 RIVET, DOME, 5/32 X .
MK-101 Pro24 JCS EXPLODED VIEW & PARTS LIST MK-101 Pro24 JCS Part # 169220 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Description CASTING, 101/990 LNR BRG MT-COM SCREW, HEX HD, 5/16 - 18 X 1 WASHER, LOCK, SPLIT, 5/16 WASHER, FLAT, SAE, 5/16 ASSEMBLY, ROLLER WHEEL SPACER, GUIDE BAR COVER, COMMON SCREW, 5/16 - 187 X 1/2 HEX HEAD MACHINE COVER, 3/4 X 37 GUIDE BAR BAR, 3/4 X 37 LINEAR GUIDE, 101 SCREW, 1/4 - 20 X 5/16 SOCKET HEAD SET SCREW, 1/4 - 20 X 1/2 SOCKET HEAD SET TABLE, PRO24, OVERMOLD (COMP) TABLE, EXTE
MK-101 Pro24 JCS EXPLODED VIEW & PARTS LIST MK-101 Pro24 Part # 158478 INCLUDED WITH ITEM 8 13 7 10 INCLUDED WITH ITEM 8 1 4 9 11 12 8 2 5 2 2 6 3 2 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 5 5 5 3 3 Description KEY, 3/16 SQ X 1 - 1/8 WASHER, FLAT, SAE, 1/4 SCREW, HEX HD, 1/4 - 20 X 3/4 ASSY, BLADE GUARD, 101 WASHER, LOCK, SPLIT, 1/4 SCREW, HEX HD, TAP, 1/4 - 20 X 1 SCREW, 5/16 - 18 X 3/8 SOCKET HEAD SET ASSY, SUB, CTTG HEAD MK-101 BELT, 6J260 PULLEY, 6J19 X 5.
MK-101 Pro24 JCS EXPLODED VIEW & PARTS LIST MK-101 Pro24 Part # 160486 2 3 1 Item 1 2 3 Description TERMINAL, 16 -14 AWG X #10 RING MTR, 1- 1/2 HP 120V 60HZ ASSY, SWITCH BOX, 30AMP, LIF11 50 Part# 154540 160484 161101 Qty 1 1 1
MK-101 Pro24 JCS EXPLODED VIEW & PARTS LIST Switch Box Part # 161101 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description washer, #10 SAE FLAT SCREW, PAN HD PHIL 6 - 32 X 5/8 WASHER #10, INTERNAL TEETH BUSHING, SWITCH, 30 AMP BOX, 30A SWITCH (COMP) SWITCH, 30 AMP MOTOR CONTROLLER PLATE, MOUNTING, SWITCH LEVER, ON/OFF, 30 AMP SWITCH GASKET, COVER, 30 AMP SWITCH SEAL, LEVER, 30 AMP SWITCH SCREW, FLAT HD PHIL 6 - 32 X 5/16 SCREW, PAN HD PHIL 10 24 X 5/16 COVER, 30A SWITCH (COMP) LEVER, ACTUATOR (COMP) S
MK-101 Pro24 JCS EXPLODED VIEW & PARTS LIST Roller Wheel Part # 151756 Item 1 2 3 4 5 Description wheel, roller nut, 1/4 - 20 hex belt, micro-v, 260j6 washer, 1/4 sae flat bracket, roller wheel 52 Part# 151799 151893 151914 151915 154021 Qty 1 1 1 1 1
MK-101 Pro24 JCS Cutting Head Part # 158191 EXPLODED VIEW & PARTS LIST 1 9 10 13 8 11 3 6 14 12 21 2 23 4 20 22 18 17 7 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 15 5 16 19 Description NUT, HEX, 5/16 - 18 flange, outer 2-3/8 nut, hex, 5/8 - 18 bearing, ball, 17 x 40 x 12mm key, 3/16 sq x 1 - 1/8 WASHER, 3/8 SAE FLAT SCREW, HEX HD, 5/16 - 18 X 1 NUT, WING, NYLK, 5/16 - 18 WASHER, 5/16 SPLIT LOCK WASHER, 5/16 SAE FLAT STRAP, 1 INCH MOTOR ADJUSTMENT BUMPER, RUBBER, 1
MK-101 Pro24 JCS EXPLODED VIEW & PARTS LIST 2 1 4 3 Item Description Part# Qty 1 2 3 4 SCREW, 5/16 - 18 X 1/2 SOCKET HEAD SET ELBOW, 1/8 MNPT X 1/4 BARB 90DEG TUBE, WATER CASTING, 101 BLD GUARD-DC-COMP 152607 154652 155389 162481 3 1 2 1 54
MK-101 Pro24 JCS ACCESSORIES ACCESSORIES ITEM NUMBER DESCRIPTION 137166 MK-200 10” x .060 x 5/8” Premium grade tile blades for fast, smooth, chip-free 128074 MK-215 18” x .060 x 5/8” Supreme grade diamond blade for hard materials 3 153252 MK-315 10” x .
MK-101 Pro24 JCS ORDERING & RETURN ORDERING INFORMATION You may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond. When ordering direct from MK Diamond, please have the following information ready before calling: • The Model Number of the saw • The Serial Number of the saw • Where the saw was purchased and when • The Part Number for the part(s) being ordered • The Part Description for the part(s) being ordered NOTE: There is a $25.
MK-101 Pro24 JCS CONTACT & WARRANTY CONTACT: Please contact MK Diamond Products, Inc. Customer Service Department with any questions you might have regarding distributors, parts or service. Telephone: (800) 421-5830 Fax: (310) 539-5158 E-mail: Customer_Service@MKDiamond.com Customer Service Hours: Monday through Friday, 6AM-4PM PST MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 MK DIAMOND PRODUCTS, INC. LIMITED WARRANTY MK DIAMOND PRODUCTS, INC.
NOTES 58
NOTES 59
MK-101 Pro24 JCS OWNERS MANUAL & OPERATING INSTRUCTIONS MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 Toll-Free: (800) 421-5830 Phone: (310) 539-5221 Fax: (310) 539-5158 www.mkdiamond.
