Owners manual

ManualsBrandsMizerak ManualsFamily RecreationDakota 8ft Billiard Table - Slate

1. READ THIS MANUAL CAREFULLY BEFORE STARTING ASSEMBLY.

Read each step completely before beginning each step.

O W N E R ' S M A N U A LO W N E R ' S M A N U A L

O W N E R ' S M A N U A L

DROP POCKET POOL TABLEDROP POCKET POOL TABLE

DROP POCKET POOL TABLE

MODEL NO .P

1270w

2. SOME SMALLER PARTS MA Y BE SHIPPED INSIDE LARGER PA RTS . CHECK INSIDE ALL PARTS

AND CARTONS BEFORE ASSEMBLING OR ORDERING PA RTS

3. USE THE HARDWARE IDENTIFIER TO IDENTIFY AND USE ALL FASTENERS. CHECK ALL CARTONS

FOR KITS. ALL HARD WARE IS LOC ATED IN ONE KIT.

THIS TABLE IS CONTAINED IN T SEPWO

ARA TE CONTAINERS:

2L-7080-00

Please visit our World W ide W

eb site at:

www .escaladesports.com

On-Line T rouble Shooting Frequently Asked Questions

Technical Assistance On-Line Parts R equests

Additional EscaladeSports Product Information

PLEASE DO NOT RETURN PRODUCT TO THE STORE!

Contact Escalade Sports customer service department at:

Phone: 1-866-556-2757 T

oll F ree!

Fax: 1-866-873-3532 T

oll Free!

E-mail: billiardtables@escaladesports.com

Mailing Address: Escalade Sports, PO Box 889, Evansville, IN 47706

Escalade Sports products may be manufactured and/or licensed under the following patents: D446275

Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

200 Escalade7 Sports

Summary of content (15 pages)

PAGE 1
O W N E R ' S M A N U A L DROP POCKET POOL TABLE MODEL NO . P1270w 1. RE AD THIS MAN UAL CA RE FU LLY BE FO RE S TARTING A SSEMBLY. Read each ste p c om pl et el y b ef or e b eginning e ach s tep. 2. SOME SMALLER PA RT S M A Y BE SH IP PE D I NSIDE L ARGER P ART S . C HECK I NSIDE A LL PARTS A ND CAR TONS BE FO RE AS SE MB LI NG OR O RDERING P ART S. 3. USE THE HARD WAR E I DE NT IF IE R T O I DENTIFY A ND USE FOR KITS . AL L H AR D WAR E I S LOCAT E D I N O NE K IT . ALL FAS TE NER S.
PAGE 2
CA UTION THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLO TH IS EXTREMELY FLAMMABLE AND UNDER PRESSURE! CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER ! KEEP OUT OF THE REACH OF SMOKING ! WORK CHILDREN! DO NOT USE OR ST ORE NEAR HEAT SOURCE ,FLAMES , SPARKS OR WHEN AREA MUST BE WELL VENTILATED . OPEN DOORS AND WINDOWS WHEN USING SPRAY ADHESIVE . To ensure safety , do not attempt to assemble system without following instructions carefully.
PAGE 3
1. Begin by opening all boxes and sort parts.Slide the eight Dove Blocks # 3 into the slots in the End Cabinet Panels # 1 and the Side Cabinet Panels # 2(See Figure 1). IMPORTANT! Do Not drive Dove Blocks into grooves with a hammer. If a block is too tight, try it in a different groove. Figure 1 2 . Attach End Cabinet Panels # 1 and Side Cabinet Panels # 2 with Corner Posts # 4, as shown in Figure 2, using four screws # 5 for each Corner Posts .
PAGE 4
6. Thread a stud # 9 halfway into each Leg # 8 7. Attach legs # 8 to Leg Blocks # 6 using the stud # 9 in Leg , one washer # 10 and one nut # 11 for each leg . Square leg up with corner of cabinet and tighten . See Figure 4 . 8. With the help of another adult , flip table over onto legs . 9. Slide Center Beam # 12 into slotin End Cabinet Panels # 1 , as shown in figure 5 , and secure each end with one screw # 14 , one washer # 15 and one dowel connector # 16 .
PAGE 5
LEVELING BASE FRAME Use a carpenter ' s level to level table as close as possible . It is easier to do it now rather than after the playfield has been attached to the frame . 13 . Determine the highest corner of the frame by placing the level in two ways shown in Figure 8 . 14 . Once you have determined the highest corner . Raise other three corners to the level of the highest corner by shimming underneath legs using playing card stock or grey leg shim stock ( # 39 ) shipped with ths table .
PAGE 6
UNBOXING THE SLATE CAUTION! AFTER CRATE PARTS ARE REMOVED , BEND NAILS OR STAPLES OVER WITH A HAMMER AT ONCE ! USE CAUTION WHEN HANDLING CRATE PARTS ! 15. Tt is now time to uncrate the slate pieces . With a claw hammer or crow bar , pry off crate top at the notched corner .( See Figure 7 ) BE CAREFUL NOT TO DAMAGE SLATE INSIDE ! SLATE IS BRITTLE AND CAN BE EASILY DAMAGED IF HIT OR PRIED AGAINST! Figure 7 16. Remove the front rail of the crate . Slide the slate out the front of the crate .
PAGE 7
THE FOLLOWING STEP REQUIRES THE HELP OF ANOTHER ADULT! Detail A Figure 10 CAUTION: Be sure countersunk holes in all three table 22 . Using four holes in slate / slatron as a guide , drill pilot holes in Cross Beams and Center B e am using a 1 / 8 " drill bit . top sections # 18 and # 19 face up : See Detail " A ", Figure Secure end sections # 18 using screws # 7 ( four scrws per 10. end section). NOTE : Be sure there are no gaps 18. NOTE : before proceeding .
PAGE 8
SHIMMING INSTRUCTIONS General Rules n Accomlish the leveling of slate / slatron with as few shims as possible possible.. n Do not top with a hammer or tighten screws unreasonable fight . You will not be able to compress the slate / slatron . You must shim up the slate / slatron to level . Shims # 37 are meant only to raise the low places at the seams and ends . Very short and low places should be grouted , Do not assume the floor is level , Most leveling can be accomplished by working with the frame frame..
PAGE 9
DO NOT SMOKE WHILE WORKING WITH CONTACT CEMENT ! READ LABEL ON CEMENT CONTAINER CAREFULLY ! Figure 12 APPLYING THE CLOTH 29 . Make sure slate / slatron is dry and free of dust . NOTE : Before spraying adhesive , cut a portion of th shipping carton to use as a shield to prevent cement overspray. 30 . Place cloth over slate / slatron with equal overhang on all sides . NOTE : Cloth may seem small but it will stretch fa great deal . Figure 13 31 .
PAGE 10
5 Figure 17 IMPORTANT! The screws #5 must be used to attach aprons. 24 and 25 26 5 41. 42. Attach side aprons #24(40-7/16") to side rails #21(40-7/16") and #22(40-7/16") using three apron brackets #26 and twelve short screws #5, as shown in Figure 17. 5 Attach end aprons #25(42") to end rails #23(42") using three apron brackets #26 and twelve short screws #5, as shown in Figure 18. 21, 22 and 23 5 Assembling Rails to the Pockets 43.
PAGE 11
21 47. 22 Figure 20 The rail cushion nose to nose dimension should measure 44 inches by 88 inches or as close as possible. See Figure 20 88 inches 44 inches 44 inches 23 44 inches 44 inches NOTE: Look along the nose rubber of the side rails to be sure they align.
PAGE 12
ONE YEAR LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product (hereinafter referred as the "P roduct"). WARRANTY DURATION:This Product is warranted to the original consumer purchase of aperiod of one (1) year from the original purchase.
PAGE 13
P1270W REPLA KEY# PART# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2W-7669-08 2W-7670-08 2W-7172-00 2W-7671-08 1B-6611-00 2W-7174-00 1B-6628-00 2W-7175-00 1B-6629-00 2B-6138-00 901-28 2W-7672-00 2W-7673-00 1B-6630-00 2B-6151-00 7B-6304-00 2W-7180-00 2W-6029-00 809-551 2W-6030-00 809-552 2A-7149-08 19 21 DESCRIPTION QTY END CABINET PANEL SIDE CABINET PANEL DOVE BLOCK WOODEN CONER POST #8 X 5/8" FLATHEAD SCREW LEG BLOCK #10 X 1-1/4" FLATHEAD SCREW LEG 3/8-16 X 5"STUD 3/8" HEAVY FLATWASHER 3/8-16 HEX NU
PAGE 14
P1270W 7 20 7 7 7 7 41 7 7 7 41 42 7 41 Page 14 NOTE : Not all parts are shown.
PAGE 15
14 3 15 16 6 44 43 8 11 10 9 2 16 4 17 7 5 NOTE : Not all parts are shown.