We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. However, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: 1-866-556-2759 FAX: 1-866-873-3531 customerservice@escaladesports.com Or write to: Escalade Sports Customer Service Department P.O. Box 889 Evansville IN 47706 Please have your model number when inquiring about parts.
IMPORTANT! READ THIS MANUAL ALL THE WAY THROUGH BEFORE BEGINNING TO PUT YOUR GAME TABLE TOGETHER! THEN READ EACH STEP BEFORE STARTING THAT STEP. TWO ADULTS ARE REQUIRED TO ASSEMBLE THIS GAME TABLE Tools Required: Allen Wrench H10 and H11 Included with the Hardware Kit Phillips Screwdriver Furniture Polish and Cloth An electric screwdriver is helpful in assembly.
© 2002 Escalade Sports 3 For Customer Service Call 1-866-556-2759
© 2002 Escalade Sports 4 For Customer Service Call 1-866-556-2759
© 2002 Escalade Sports 5 For Customer Service Call 1-866-556-2759
1. Find a clean, level place to begin the assembly of your pool table. We recommend building the table on the box top to protect the parts during assembly. 2. Place the main cabinet P1 on the ground with the playing side down. 3. Apply glue P12 to ALL the edges and ends of the long rail sections P1A and P1B and the short rail sections P1C, P1D, and P1E that will be attached to one another. 4.
5. Attach legs P2A and P2B to the return end of the table using bolts H1 and washers H8 as shown in FIGURE 2. The leg bolts go from the inside of the leg toward the frame pieces as shown. Make sure you start all bolts by hand before you tighten anything. Figure 2 6. Attach legs P2A and P2B to the other end of the table using bolts H1 and washers H8 as shown in FIGURE 3. The leg bolts go from the inside of the leg toward the frame pieces as shown.
7. Attach the two spreaders P3 and the two end panels P4 as shown in FIGURE 4 using bolts H2 washers H9 and nuts H5. 8. Attach one leg leveler P5 to the bottom of each leg as shown in FIGURE 4. Figure 4 9. Lay the apron side panels P7A and P7B on a flat surface with the woodgrain side facing out and the screw holes at the bottom of the panels. 10. Attach the two apron corners P10 with the arrows facing up, to the side panels P7A and P7B using screws H4 as shown in FIGURE 5.
11. Position the apron side panels P7A and P7B on the main cabinet P1 as shown in FIGURE 6. The panels are positioned correctly when the apron corners P10 rest inside the corner caps that are attached to the main cabinet. Once you have the side panels placed correctly, attach them to the main cabinet using screws H3 as shown in Figure 6. 12. Slide the apron end panel P8 into each apron corner P10 and attach to apron corners using screws H4.
14. Attach two apron corners P10 to each end of apron ball return panel P9 with the arrows facing up using screws H4 as shown in FIGURE 7. 15. Attach the assembled apron return panel P9 toboth apron side panels P7A and P7B using screws H4. Attach the apron to the main cabinet P1 using screws H3 as shown in FIGURE 7. Figure 7 16. Bend the short return board P11 by hand and insert into the groves of both apron side panels P7A and P7B by sliding first in the direction noted by an “X” as shown in FIGURE 8.
THIS STEP REQUIRES TWO OR MORE ADULTS. VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON ITS LEGS. BE CAREFUL, THE TABLE IS VERY HEAVY. 19. After the glue has dried (Approximately 12 Hours) turn the table over. Put the table in its final resting place in your room. Using a capenters level or rolling a pool ball on the surface, level the table by turning the leg levelers P5. Start by adjusting the lowest corner first and then work your way around the table. 20.
8 - BALL Eight-Ball is a call shot game played with a cue ball and 15 object balls, numbered 1 through 15. One player must pocket balls of the group numbered 1 through 7 (solid colors), while the other player has 9 through 15 (stripes). The player pocketing either group first, and then legally pocketing the 8-ball wins the game. CALL SHOT In Call Shot, obvious balls and pockets do not have to be indicated. It is the opponent’s right to ask which ball and pocket if he is unsure of the shot.
SCRATCH ON A LEGAL BREAK If a player scratches on a legal break shot, (1) all balls pocketed remain pocketed (exception, the 8ball: see rule “Object Balls Jumped Off Table On Break”), (2) it is a foul, (3) the table is open. Please Note: The incoming player has cue ball in hand behind the head string and may not shoot an object ball that is behind the head string, unless he first shoots the cue ball past the head string and causes the cue ball to come back behind the head string and hit the object ball.
SCORING A player is entitled to continue shooting until failing to legally pocket a ball of his group. After a player has legally pocketed all of his group of balls, he shoots to pocket the 8-ball. FOUL PENALTY Opposing player gets cue ball in hand. This means that the player can place the cue ball anywhere on the table (does not have to be behind the head string except on opening break). This rule prevents a player from making intentional fouls which would put an opponent at a disadvantage.
9 - BALL OBJECT OF THE GAME Nine-Ball is played with nine object balls numbered one through nine and a cue ball. On each shot, the first ball the cue ball contacts must be the lowest numbered ball on the table, but the balls need not be pocketed in order. If a player pockets any ball on a legal shot, he remains at the table for another shot, and continues until missing, committing a foul, or wining the game by pocketing the 9ball.
PUSH OUT The player who shoots the shot immediately after a legal break may play a push out in an attempt to move the cue ball into a better position for the option that follows. On a push out, the cue ball is not An illegal push out is penalized according to the type of foul committed. After a player scratches on the break shot, the incoming player cannot play a push out.
PRODUCT PARTS LIST Part # H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 P1 P1A P1B P1C P1D P1E P1F P2A P2B P3 Description 5/16 x 1-1/4 Bolt 1/4 x 1-1/4 Bolt 1-1/4 Flat Head Screw 5/8 Round Head Screw 1/4 Hex Nut 1” Round Head Screw Bracket 5/16 Flat Washer 1/4 Flat Washer Allen Wrench Open End Wrench Main Cabinet Long Rail (Right) Long Rail (Left) Short Rail Ends W/Hole Short Rail Center Short Rail Return End Hinge Right Leg Left Leg Spreader © 2002 Escalade Sports Model # G07601 Qty.
90 DAY LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of 90 days from the original purchase.
