We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. Howeve r, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: 1-866-556-2757 FAX: 1-866-873-3531 pooltables@escaladesports.com Or write to: Escalade Sports Customer Service Department P.O. Box 889 Evansville IN 47706 Please have your model number when inquiring about parts.
CAUTION THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS EXTREMELY FLAMMABLE AND UNDER PRESSURE ! CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER ! KEEP OUT OF THE REACH OF CHILDREN ! DO NOT USE OR STORE NEAR HEAT SOURCE , FLAMES , SPARKS OR WHEN SMOKING ! WORK AREA MUST BE WELL VENTILATED . OPEN DOORS AND WINDOWS WHEN USING SPRAY ADHESIVE . To ensure safety, do not attempt to assemble system without followinginstructions carefully.
Pa r t Li s t (To Scale) H2 - 3/8” Lock Washer (16 pcs) H1 - 3/8” x 2-1/4” Bolt (8 pcs) H5 - 3/8” x 3” Bolt (8 pcs) H8 - 5/16” x 1-1/4” Bolt (8 pcs) H6 - WP/4 x 1” Phillips Washer Head Screw (12 pcs) H9 - 5/16” x 1-3/4” Bolt (12 pcs) H12 - 5/16” x 1-5/8” Bolt (18 pcs) H13 - 5/16” x 32mm Flat Washer (18 pcs) H16 - 1/4” x 1-1/2” Bolt (4 pcs) H17 - 1/4” x 15mm Flat Washer (4 pcs) All Rights Reserved.
A1 A3 A2 Cu e Stic k 2 Pcs A5 Triangl e 1 Pc A4 Playfield Cloth Brush 1 Pc Playfield Cloth 1 Pc A6 Billiar d Bal l 1 Se t Cue Chalk 2 Pc s Playfield Grout Kit 1 Pc Playfield Cloth to Playfield - Spray Adhesive 1 Pc Wrench 1 Set Sand Paper for Dried Grout 1 Pc P2 P1 T4 T3 T2 T1 P4 P3A NOTE: For P5 Installation. P3B NOTE: For P16 Installation.
P13 P15 P14 End Apron 1 Pc P17 End Apron with Ball Return Opening 1 Pc P19 Leg Leveler 4 Pcs P20 Right Corner Pocket 1 Pc Left Corner Pocket Right Corner Pocket NOTE: Attach this pocket on same end as P14 Apron with Ball Return Opening 1 Pc Right Middle Pocket 1 Pc P24 P23 P22 P21 Ball Return Support Board 1 Pc Corner Post 4 Pcs P18 Ball Return Tray Board 1 Pc P16 Left Corner Pocket 1 Pc Left Middle Pocket 1 Pc NOTE: Attach this pocket on same end as P14 Apron with Ball Return Openi
PARTS REQUIRED: 2 pcs - P1 Leg 4 pcs - P18 Leg Leveler ST E P 1 : Thread P18 Leg Levelers into P1 Leg as shown in Figure 1. . P18 Note: Remove Parts Box, Leg Levelers, Plastic Pockets and Spray Glue from inside both Legs. P18 Figure 1 All Rights Reserved.
8 pcs 16 pcs 32 pcs 16 pcs 8 pcs 8 pcs ST E P 2 : - PARTS REQUIRED: H1 Bolt H2 Lock Washer H3 Washer H4 Hex Nut H5 Bolt H6 Screw 2 pcs - P2 Main Metal Beam 2 pcs - P3A & P3B End Slat 2 pcs - P4 Middle Slat 2 pcs - P5 End Board 1 pc - P16 Ball Return Support Board 1 set - T4 Wrench Attach each P2 Main Metal Beam to P1 Leg assembly as shown Figure 2 using H1 Bolts, H3 Washers, H2 Lock Washers and H4 Hex Nuts. Use the T4 Wrench to assemble the hardware. Do not tighten hardware at this time.
STE P 4 : Us e a carpente r ’ s leve l t o leve l tabl e a s clos e a s possible . It i s easie r t o d o i t no w rather than after the Play Bed is on the frame. To determine the highest corner of the frame place the level in following two positions. First check the table from end to end as shown in Figure 4. Then check the table at an angle as shown in Figure 5. Can also use playing cards for Slate / Slatron Shimming - not included. Figure 4 Figure 5 All Rights Reserved.
UNBOX I N G TH E SL AT E (Slat e t a b l e s o nl y: ) ! CAUTIO N ! AFTE R CR AT E PA R T S AR E REM O VED , B EN D NA I L S O R S TAP L E S O VE R W I T H A HAM M E R AT O NCE ! U S E CAUT IO N WHE N HAND LI N G CR AT E PA R TS ! Figure 6 I t i s n o w t im e t o u ncr a t e t h e s l a t e pi e c e s . W i t h a c la w hamme r o r c ro w ba r, p r y o f f c ra t e to p a t t h e notche d corne r.
PARTS REQUIRED: THE FOLLOWING STEP REQUIRES THE HELP OF ANOTHER ADULT! 16 pcs - H7 Screw 2 pcs - P6 End Play Bed 1 pcs - P7 Middle Play Bed STEP 5: You can tell the top side of the playfield sections by the beveled edge of the pocket openings and the countersunk mounting holes. The beveled edges and the countersunk holes must face up. (See Detail A) A) Place center section P7 on the two long slats P4.If edges do not align exactly,center playfield as much as you can.
SHIMMING INSTRUCTIONS ( use deck of cards for shimming, not included ) General Rules Accomplish the leveling of the playing surface with as few shims as possible. Do not tap with a hammer or tighten screws unreasonably tight. You will not be able to compress the playing surface. You must shim up the playing surface to level. Shims are meant only to raise the low places at the seams and ends. Very short and low places should be grouted. Do not assume the floor is level.
! WARNING ! First Glue Application DO NOT SMOKE WHILE WORKING WITH CONTACT CEMENT! READ LABEL ON CEMENT CONTAINER CAREFULLY! Applying the cloth: 1. Make sure Play Bed is dry and free of dust. NOTE: Before spraying adhesive, cut a portion of the shipping carton to use as a shield to prevent cement over spray. 2. Place cloth over Play Bed with equal overhang on all sides. Figure 10 Spray glue on edge of slate too. Second Glue Application NOTE: Cloth may seem small but it will stretch a great deal. 3.
PARTS REQUIRED: 8 pcs - H8 Bolt 8 pcs - H15 Flat Washer 2 pcs - P9 Side Top Rail 2 pcs - P10 End Top Rail 4 pcs - P11 Corner Cap STEP 6: On a clean level surface, lay each P9 Side Top Rail and P10 End Top Rail face down as shown in Figure 15. Next, lay each P11 Corner Cap face down and attach using H8 Bolts with H15 Flat Washers as shown in Figure 15 and Detail A. Do not tighten H8 Bolts at this time.
PARTS REQUIRED: 12 pcs - H11 Screw 1 pc - P13 End Apron 1 pc - P14 End Apron with Ball Return Opening 4 pcs - P15 Corner Post STEP 7: Slide and attach each P15 Corner Post onto the end of each P13 and P14 End Apron using H11 Screws as shown in Figure 16A. Tighten, but do not strip out H11 Screws. IMPORTANT NOTE: Study and assemble parts exactly as per Figure 16A. INCORRECT IF GROOVE FACE UPWARD NOTE: BE SURE EACH CORNER POST IS FLUSH WITH END APRON.
PARTS REQUIRED: 12 pcs - H9 Bolt 12 pcs - H10 Washer 12 pcs - H11 Screw 2 pcs - P12 Side Apron STEP 8: With the rail assembly face down, attach P12 Side Aprons using H9 Bolts with H10 Washers (see inset). Do not tighten yet. Next, attach previous assemblies P13 and P14 End Aprons flush against the bottom of the P10 End Top Rail and align using threaded inserts on the underside of each rail. Attach P13 and P14 End Apron assembly using H9 Bolts with H10 Washers (see inset). Do not tighten yet.
PARTS REQUIRED: 18 pcs - H12 Bolt 18 pcs - H13 Washer STEP 9: With the help of four adults, carefully rotate the rail and apron assembly and then place over the play bed as shown. From the underside of the table, insert H12 Bolts with H13 Washers up through the play bed and into the threaded inserts of each rail. Be sure the rail assembly is aligned with the play bed and pockets, then tighten all bolts.
PARTS REQUIRED: 1 pc - P19 Right Corner Pocket 1 pc - P20 Right Middle Pocket 1 pc - P21 Right Corner Pocket 1 pc - P22 Left Corner Pocket 1 pc - P23 Left Middle Pocket 1 pc - P24 Left Corner Pocket 4 pcs - P25 Ball Return Tube STEP 10: Connect P22 Left Corner Pocket, P23 Left Middle Pocket and P24 Left Corner Pocket with P25 Ball Return Tubes as shown in Figure 18.
THIS STEP REQUIRES THREE OR MORE ADULTS. VERY CAREFULLY INSERT RIGHT POCKET RETURN AND LEFT POCKET RETURN INTO THE DROP POCKET OPENINGS FROM UNDERSIDE OF THE TABLE. PARTS REQUIRED: 36 pcs - H14 Pocket Nail STEP 11: Insert Right Pocket Return and Left Pocket Return from previous assembly STEP 10 into the drop pocket openings from underside of the table. Fasten pockets using six H14 Nails per pocket. Hold the nails with needle nose pliers and tap them in with a small hammer.
PARTS REQUIRED: 4 pcs - H6 Screw 4 pcs - H16 Bolt 4 pcs - H17 Washer 1 pc - P17 Ball Return Tray Board 2 pcs - A1 Cue Stick 1 pc - A2 Triangle 1 pc - A3 Brush 1 set - A5 Billiard Ball 2 pcs - A6 Chalk STEP 12: Attach P17 Ball Return Tray Board onto P16 Ball Return Support Board using H16 Bolts and H17 Washers as shown in Figure 21. Attach P17 Ball Return Tray Board onto P14 End Apron with Opening Ball Return Trim using H6 Screws as shown in Figure 21. Tighten, but do not strip out H6 Screws.
Congratulations! You have now assembled your pool table. Please note the Care and Use instructions below to insure many years of trouble free use of your pool table. CARE AND USE OF YOUR POOL TABLE 1. 2. 3. 4. 5. 6. 7. 8. Use spray furniture polish to clean all exterior surfaces of your pool table. Use the table brush provided to clean the cloth on the table. Use a carpenters level to properly level table using the leg levelers. This product is intended for INDOOR use only.
PARTS LIST FOR MODEL # P5423W PART # P5423WWJH1 P5423WWJH2 P5423WWJH3 P5423WWJH4 P5423WWJH5 P5423WWJH6 P5423WWJH7 P5423WWJH8 P5423WWJH9 P5423WWJH10 P5423WWJH11 P5423WWJH12 P5423WWJH13 P5423WWJH14 P5423WWJH15 P5423WWJH16 P5423WWJH17 P5423WWJT1 P5423WWJT2 P5423WWJT3 P5423WWJT4 P5423WWJA1 P5423WWJA2 P5423WWJA3 P5423WWJA4 P5423WWJA5 P5423WWJA6 P5423WWJP1 P5423WWJP2 P5423WWJP3A P5423WWJP3B P5423WWJP4 P5423WWJP5 P5423WWJP6 P5423WWJP6S P5423WWJP7 P5423WWJP7S P5423WWJP8 P5423WWJP9 P5423WWJP10 P5423WWJP11A P5423WWJP
90 DAY LIMITED WARRANTY This customer warranty extends to the original owner, on the purchase of any ESCALADE SPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original owner, for a period of 90 days from the original purchase. WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original owner, this product to be free from defects in material and workmanship when used for the intended purpose under normal use and conditions.
