Installation Sheet
Table Of Contents
- ,HL111101G,
- GENERAL
- INSTALLATION TO OUTLET BOX
- STEP 1. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws.
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- STEP 5. Carefully place connections back into the outlet box.
- STEP 6. Place Back plate over the mounting plate and secure with set screws.
- STEP 7. Screw in decorative plug into the bottom of the backplate.
- STEP 1. Lift glass shade up over the glass fitter and secure with thumb screws.
- STEP 8. Install the lamp(s). The fixture is rated for 60 watt G lamp.
- DO NOT EXCEED RECOMMENDED WATTAGE!
- STEP 9. Restore power to the circuit at breaker or fusebox.
- INSTALLATION USING STEM/PLUG
- STEP 2. Remove the mounting plate from the backplate
- STEP 3. Determine the location for the lamp. Using the mounting plate as a template, mark the location of the holes for the wall anchors.
- STEP 4. Drill the appropriate size holes for the wall anchors (holes should be slightly smaller than the size of the anchors).
- STEP 5. Install the wall anchors, and anchor screws.
- STEP 6. Install the mounting plate to the anchor screws using the key slot
- STEP 7. Attach stem to the bottom of the backplate, and feed cord through the stem.
- STEP 8. Connect the cord to the stem using the procedures outlined in steps 2-4 of the outlet box installation above
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- STEP 9. Place the fixture to the wall over the mounting plate and secure using the set screws.
- STEP 10. Lift glass shade up over the glass fitter and secure with thumb screws.
- STEP 11. Install the lamp(s). The fixture is rated for 60 watt G lamp.
- DO NOT EXCEED RECOMMENDED WATTAGE!
- STEP 10. Plug cord into a qualified socket of properly rated voltage.
- DIMMING
- CLEANING
- ASSEMBLY AND MOUNTING DIAGRAM
- WIRE NUT/TAPING DIAGRAM
- ,HL111 101G M40
- GENERALITÉ
- INSTALLATION À LA BOÎTE DE DÉRIVATION
- STEP 1. Retirer les fils de la boîte de dérivation et installer la plaque de montage à la boîte de dérivation au moyen des (2) vis de montage.
- INSTALLATION UTILISANT TIGE/FICHE
- STEP 6. Fixer la tige vers le bas de la plaque arrière et faire passer le cordon par la tige.
- STEP 7. Relier le cordon à la tige comme indiqué aux pas 2-4 de l’installation de la boîte à dérivation ci-haut.
- STEP 8. Placer le dispositif à la paroi sur la plaque de montage et sécuriser à l’aide des vis de fixation.
- RÈGLAGE D’INTENSITÉ
- NETTOYAGE
- SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
- SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
HL111101G RILEY
SCONCE
www.hudsonvalleylighting.com/mitzi | #mymitzi
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL
•
WARNING-DISCONNECT POWER BEFORE RELAMPING OR
WIRING THE FIXTURE. TURN OFF THE ENTIRE ELECTRICAL
CIRCUIT TO WHICH THE LIGHTING FIXTURE IS ATTACHED
•
INSTALLATION AND MAINTENANCE OF THIS FIXTURE
SHOULD BE COMPLETED BY A LICENSED ELECTRICAN
•
FAILURE TO INSTALL FIXTURE CORRECTLY COULD RESULT
IN SERIOUS INJURY OR DEATH
•
READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION.
•
IF AN EXISTING FIXTURE IS BEING REPLACED, REMOVE IT
AND
NOTE TO WHICH WIRE IN THE OUTLET BOX THE
ORIGINAL FIXTURE WAS ATTACHED.
•
BEFORE DISCARDING THE CARTON DOUBLE CHECK THE
PACKAGING TO MAKE SURE ALL PARTS HAVE BEEN FOUND.
•
THIS FIXTURE WAS DESIGNED TO BE MOUNTED TO AN
OCTAGON OUTLET BOX. THE BOX MUST BE SECURELY
MOUNTED TO THE STRUCTURE OF THE BUILDING.
INSTALLATION TO OUTLET BOX
STEP 1. Pull the wires out from the outlet box, and install
mounting plate onto the outlet box using the (2)
mounting screws.
STEP 2. Fasten bare ground wire to ground wire from the wall
outlet box (usually green or copper color) or connect
ground wire to green screw on the mounting plate.
STEP 3. Connect the neutral (white) fixture wire coming from the
fixture base to neutral (usually white) outlet wire. Fasten
both wires together with a plastic wire nut and tightly
wrap the wire nut with electrical tape.
STEP 4. Repeat the previous step with the hot (black wires). Make
sure there are no exposed wires or strands that could
cause a dangerous short circuit.
FAILURE TO CONNECT THE APPROPRIATE WIRES
STEP 5.
STEP 6.
STEP 7.
STEP 1.
STEP 8.
STEP 9.
CORRECTLY COULD
RESULT IN SERIOUS INJURY OR
DEATH!
Carefully place connections back into the outlet box.
Place Back plate over the mounting plate and secure with
set screws.
Screw in decorative plug into the bottom of the
backplate.
Lift glass shade up over the glass fitter and secure with
thumb screws.
Install the lamp(s). The fixture is rated for 60 watt G lamp.
DO NOT EXCEED RECOMMENDED WATTAGE!
Restore power to the circuit at breaker or fusebox.
INSTALLATION USING STEM/PLUG
STEP 2. Remove the mounting plate from the backplate
STEP 3. Determine the location for the lamp. Using the mounting
plate as a template, mark the location of the holes for the
wall anchors.
STEP 4. Drill the appropriate size holes for the wall anchors (holes
should be slightly smaller than the size of the anchors).
STEP 5. Install the wall anchors, and anchor screws.
STEP 6. Install the mounting plate to the anchor screws using the
key slot
STEP 7. Attach stem to the bottom of the backplate, and feed
cord through the stem.
STEP 8. Connect the cord to the stem using the procedures
outlined in steps 2-4 of the outlet box installation above
FAILURE TO CONNECT THE APPROPRIATE WIRES
CORRECTLY COULD RESULT IN SEROIUS INJURY OR
DEATH!
STEP 9. Place the fixture to the wall over the mounting plate and
secure using the set screws.
STEP 10. Lift glass shade up over the glass fitter and secure with
thumb screws.
STEP 11. Install the lamp(s). The fixture is rated for 60 watt G lamp.
DO NOT EXCEED RECOMMENDED WATTAGE!
STEP 10. Plug cord into a qualified socket of properly rated
voltage.
IMPORTANT SAFETY INSTRUCTION: THIS PORTABLE
LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER
THAN THE OTHER). THIS PLUG CAN BE USED IN A
POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG
DOES NOT FIT FULLY INTO THE OUTLET, REVERSE THE
PLUG. IF IT STILL DOES NOT FIT CONTACT A
QUALIFIED ELECTRICAN. NEVER USE WITH AN
EXTENSION CORD UNLESS THE PLUG CAN BE FULLY
INSERTED. DO NOT ALTER THE PLUG
DIMMING
The fixture can be controlled by a wall dimming device. Only use
triac/electronic dimmer. Make sure carton is marked for use with LED
compact fluorescent-incandescent light source only. These can be
provided by your local electrical distributor, home center, or
hardware store.