Installation Sheet
Table Of Contents
- ,H196503,
- GENERAL
- INSTALLATION
- STEP 1. Attach the mounting plate to the outlet box using the mounting screws.
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH !
- STEP 5. Carefully place wires into Outlet Box.
- STEP 6. Place the canopy with the fixture over the outlet box and fasten it by the screw collar.
- STEP 7. Install the lamps. The fixture is rated for 4 watt G9 LED.
- DO NOT EXCEED RECOMMENDED WATTAGE!
- STEP 8. Assemble the glass shade onto glass fitter.
- STEP 9. Restore power to the circuit at breaker or fuse box.
- DIMMING
- CLEANING
- ASSEMBLY AND MOUNTING DIAGRAM
- WIRE NUT/TAPING DIAGRAM
- H196 503 M41
- GENERALITÉ
- INSTALLATION
- PAS 3. Relier le fil neutre (blanc) venant de la base du dispositif au fil neutre (généralement blanc) de la boîte de dérivation. Relier les deux fils entre eux à l’aide d’un serre-câble en plastique et envelopper le serre-câble de ruban isolant bien ...
- RÈGLAGE D’INTENSITÉ
- NETTOYAGE
- SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
- SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
H196503 LOLA
FLUSH MOUNT
www.hudsonvalleylighting.com/mitzi| #mymitzi
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL
•
WARNING-DISCONNECT POWER BEFORE RELAMPING OR
WIRING THE FIXTURE. TURN OFF THE ENTIRE ELECTRICAL
CIRCUIT TO WHICH THE LIGHTING FIXTURE IS ATTACHED
•
INSTALLATION AND MAINTENANCE OF THIS FIXTURE
SHOULD BE COMPLETED BY A LICENSED ELECTRICAN
•
FAILURE TO INSTALL FIXTURE CORRECTLY COULD RESULT
IN SERIOUS INJURY OR DEATH
•
READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION.
•
IF AN EXISTING FIXTURE IS BEING REPLACED, REMOVE IT AND
NOTE TO WHICH WIRE IN THE OUTLET BOX THE ORIGINAL
FIXTURE WAS ATTACHED.
•
BEFORE DISCARDING THE CARTON DOUBLE CHECK THE
PACKAGING TO MAKE SURE ALL PARTS HAVE BEEN FOUND.
•
THIS FIXTURE WAS DESIGNED TO BE MOUNTED TO AN
OCTAGON OUTLET BOX. THE BOX MUST BE SECURELY
MOUNTED TO THE STRUCTURE OF THE BUILDING.
INSTALLATION
STEP 1. Attach the mounting plate to the outlet box using the
mounting screws.
STEP 2. Fasten bare ground wire to ground wire from the wall
outlet box (usually green or copper color) or connect
ground wire to green screw on the mounting plate.
STEP 3. Connect the neutral (white) fixture wire coming from the
fixture base to neutral (usually white) outlet wire. Fasten
both wires together with a plastic wire nut and tightly
wrap the wire nut with electrical tape.
STEP 4. Repeat the previous step with the hot (black wires). Make
sure there are no exposed wires or strands that could
cause a dangerous short circuit.
S
TEP 5.
STEP 6.
STEP 7.
STEP 8.
STEP 9.
FAILURE TO CONNECT THE APPROPRIATE WIRES
CORRECTLY COULD RESULT IN SERIOUS INJURY OR
DEATH !
Carefully place wires into Outlet Box.
Place the canopy with the fixture over the outlet box and
fasten it by the screw collar.
Install the lamps. The fixture is rated for 4 watt G9 LED.
DO NOT EXCEED RECOMMENDED WATTAGE!
Assem
ble the glass shade onto glass fitter.
Restore power to the circuit at breaker or fuse box.
DIMMING
The fixture can be controlled by a wall dimming device. Only use
triac/electronic dimmer. Make sure carton is marked for use with LED
compact fluorescent-incandescent light source only. These can be
provided by your local electrical distributor, home center, or
hardware store.
CLEANING
Please clean with a soft, dry cloth ONLY! Do not use cleaning products.