Installation Sheet
Table Of Contents
- ,H105603,
- GENERAL
- INSTALLATION
- STEP 1. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws. Strip the Fixture wire ends 5/8”
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- STEP 5. Carefully place connections back into the outlet box
- STEP 6. Place canopy over the mounting plate and secure with Set Screws
- STEP 7. Install the lamp(s). The fixture is rated for 60 watt type A lamp.
- DO NOT EXCEED RECOMMENDED WATTAGE
- STEP 8. Unscrew Screw checker and slide the glass cover up
- STEP 9. Tilt the glass shade slightly and lift up so the glass support is inside the glass. Straighten out the Glass shade and rest on glass support.
- STEP 10. Slide down the glass cover and screw the screw checker back onto the arm.
- STEP 11. Restore power to the circuit at breaker or fusebox.
- DIMMING
- CLEANING
- ASSEMBLY AND MOUNTING DIAGRAM
- WIRE NUT/TAPING DIAGRAM
- ,H105603 M36
- GENERALITÉ
- INSTALLATION
- STEP 1. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws. Strip the Fixture wire ends 5/8”
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- STEP 5. Carefully place connections back into the outlet box
- STEP 6. Place canopy over the mounting plate and secure with Set Screws
- STEP 7. Install the lamp(s). The fixture is rated for 60 watt type A lamp.
- DO NOT EXCEED RECOMMENDED WATTAGE
- STEP 8. Unscrew Screw checker and slide the glass cover up
- STEP 9. Tilt the glass shade slightly and lift up so the glass support is inside the glass. Straighten out the Glass shade and rest on glass support.
- STEP 10. Slide down the glass cover and screw the screw checker back onto the arm.
- STEP 11. Restore power to the circuit at breaker or fusebox.
- RÈGLAGE D’INTENSITÉ
- NETTOYAGE
- SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
- SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
H105603 STELLA
FLUSH MOUNT
www.hudsonvalleylighting.com/mitzi | #mymitzi
NOTICE D'ASSEMBLAGE ET DE MONTAGE
GENERALITÉ
•
AVERTISSEMENT - DÉBRANCHER LE COURANT AVANT DE
REMPLACER UNE AMPOULE OU DE RELIER LE DISPOSITIF AU
COURANT. COUPER INTÉGRALEMENT LE CIRCUIT ÉLÉCTRIQUE
AUQUEL LE DISPOSITIF EST RELIÉ.
•
L'INSTALLATION ET L'ENTRETIEN DE CE DISPOSITIF DOIVENT ÊTRE
REALISÉS PAR UN ÉLECTRICIEN AGRÉÉ.
•
UNE INSTALLATION INCORRECTE DE L'APPAREIL PEUT ENTRAINER
DES BLESSURES GRAVES OU LA MORT.
VEUILLER LIRE TOUTE LA NOTICE AVANT DE PROCEDER À
L'INSTALLATION.
•
EN CAS DE REMPLACEMENT D'UN APPAREIL EXISTANT RETIRER
CELUI-CI ET NOTER À QUELS CÂBLES DE LA BOîTE DE DÉRIVATION
LE DISPOSITIF ORIGINAL ÉTAIT RELIÉ.
•
AVANT DE JETER LA BOÎTE D'EMBALLAGE, CONTRÔLER
L'EMBALLAGE POUR S'ASSURER QUE TOUTES LES PIÈCES ONT ÉTÉ
TROUVÉES.
CE DISPOSITIF A ÉTÉ CONÇU POUR ÊTRE MONTÉ SUR UNE
BOÎTE DE DÉRIVATION OCTOGONALE. LA BOÎTE DOIT ÊTRE
FIXÉE DE MANIÈRE SÛRE À LA STRUCTURE DE L'IMMEUBLE.
INSTALLATION
STEP 1. Pull the wires out from the outlet box, and install
mounting plate onto the outlet box using the (2)
mounting screws. Strip the Fixture wire ends 5/8”
STEP 2. Fasten bare ground wire to ground wire from the wall
outlet box (usually green or copper color) or connect
ground wire to green screw on the mounting plate.
STEP 3. Connect the neutral (white) fixture wire coming from the
fixture base to neutral (usually white) outlet wire. Fasten
both wires together with a plastic wire nut and tightly
wrap the wire nut with electrical tape.
STEP 4. Repeat the previous step with the hot (black wires). Make
sure there are no exposed wires or strands that could
cause a dangerous short circuit.
FAILURE TO CONNECT THE APPROPRIATE WIRES
CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
STEP 5. Carefully place connections back into the outlet box
STEP 6. Place canopy over the mounting plate and secure with
Set Screws
STEP 7. Install the lamp(s). The fixture is rated for 60 watt type A
lamp.
DO NOT EXCEED RECOMMENDED WATTAGE
STEP 8. Unscrew Screw checker and slide the glass cover up
STEP 9. Tilt the glass shade slightly and lift up so the glass
support is inside the glass. Straighten out the Glass shade
and rest on glass support.
STEP 10. Slide down the glass cover and screw the screw checker
back onto the arm.
STEP 11. Restore power to the circuit at breaker or fusebox.
RÈGLAGE D’INTENSITÉ
Le dispositif peut être contrôlé par un variateur de lumière de paroi. incadescente. Celle-ci peuvent être fournies par votre distributeur
N’utiliser qu’un variateur de lumière triad/électronique. S’assurer de matériel électrique local, par un centre de bricolage ou par une
que l’emballage porte la mention précisant de n’utiliser le dispositif quincaillerie.
qu’avec une source lumineuse LED compact fluorescente
NETTOYAGE
A nettoyer UNIQUEMENT avec un chiffon doux et sec! Ne pas utiliser de produits de nettoyage.
•
•
Retirer les fils de la boîte de dérivation et installer la plaque
de montage sur la boîte de dérivation au moyen des (2) vis
de montage.
Dénuder chaque fil jusqu’à 1,6cm (5/8”)
Fixer le fil de terre dénudé au fil de terre de la boîte de
dérivation à la paroi (généralement de couleur verte ou
cuivre) ou relier le fil de terre à la vis verte sur la plaque de
montage.
Relier le fil neutre (blanc) venant de la base du
dispositif au
fil neutre (généralement blanc) de la boîte de dérivation.
Relier les deux fils entre eux à l’aide d’un serre
-câble en
plastique et envelopper le serre
-câble de ruban isolant bien
serré.
Répéter le pas précédent avec les fils de phase (noirs
).
S’assurer qu’il n’y a pas de fils exposés ou de brins
qui pourraient causer un dangereux court
-circuit.
UNE CONNEXION INCORRECTE OU D
ES FILS INAPPROPRIÉS
PEUT ENTRAÎ
NER DE GRAVES BLESSURES OU LA MORT!
Remettre soigneusement les connexions dans la boîte de
dérivation
.
Placer le cache
-piton sur la plaque de montage et fixer en
place à l’aide des vis de fixation.
Installer la ou les ampoules. Le dispositif est prévu pour des
ampoules de 60 watt de type A.
NE PAS DÉPASSER LE WATTAGE RECOMMANDÉ!
Dévisse
r la bague à vis
et glisser le pavillon de verre vers le
haut.
Incliner légèrement l’abat
-jour en verre et le soulever afin
que le support du verre se trouve à l’intérieur
du verre.
Redresser l’abat
-jour en verre et le reposer sur le support
de verre.
Gli
sser vers le bas le pavillon de verre et revisser la bague
à vis au bras.
Rebrancher le couran
t au disjoncteur ou à la boîte
fusibles.
PAS 1.
PAS 2.
PAS 3.
PAS 4.
PAS 5.
PAS 6.
PAS 7.
PAS 8.
PAS 9.
PAS 10.
PAS 11.