Installation Sheet
Table Of Contents
- ,H105603,
- GENERAL
- INSTALLATION
- STEP 1. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws. Strip the Fixture wire ends 5/8”
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- STEP 5. Carefully place connections back into the outlet box
- STEP 6. Place canopy over the mounting plate and secure with Set Screws
- STEP 7. Install the lamp(s). The fixture is rated for 60 watt type A lamp.
- DO NOT EXCEED RECOMMENDED WATTAGE
- STEP 8. Unscrew Screw checker and slide the glass cover up
- STEP 9. Tilt the glass shade slightly and lift up so the glass support is inside the glass. Straighten out the Glass shade and rest on glass support.
- STEP 10. Slide down the glass cover and screw the screw checker back onto the arm.
- STEP 11. Restore power to the circuit at breaker or fusebox.
- DIMMING
- CLEANING
- ASSEMBLY AND MOUNTING DIAGRAM
- WIRE NUT/TAPING DIAGRAM
- ,H105603 M36
- GENERALITÉ
- INSTALLATION
- STEP 1. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws. Strip the Fixture wire ends 5/8”
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- STEP 5. Carefully place connections back into the outlet box
- STEP 6. Place canopy over the mounting plate and secure with Set Screws
- STEP 7. Install the lamp(s). The fixture is rated for 60 watt type A lamp.
- DO NOT EXCEED RECOMMENDED WATTAGE
- STEP 8. Unscrew Screw checker and slide the glass cover up
- STEP 9. Tilt the glass shade slightly and lift up so the glass support is inside the glass. Straighten out the Glass shade and rest on glass support.
- STEP 10. Slide down the glass cover and screw the screw checker back onto the arm.
- STEP 11. Restore power to the circuit at breaker or fusebox.
- RÈGLAGE D’INTENSITÉ
- NETTOYAGE
- SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
- SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
H105603 STELLA FLUSH MOUNT
www.hudsonvalleylighting.com/mitzi | #mymitzi
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL
•
WARNING-DISCONNECT POWER BEFORE RELAMPING OR
WIRING THE FIXTURE. TURN OFF THE ENTIRE ELECTRICAL
CIRCUIT TO WHICH THE LIGHTING FIXTURE IS ATTACHED
•
INSTALLATION AND MAINTENANCE OF THIS FIXTURE
SHOULD BE COMPLETED BY A LICENSED ELECTRICAN
•
FAILURE TO INSTALL FIXTURE CORRECTLY COULD RESULT IN
SERIOUS INJURY OR DEATH
•
READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION.
•
IF AN EXISTING FIXTURE IS BEING REPLACED, REMOVE IT
AND NOTE TO WHICH WIRE IN THE OUTLET BOX THE
ORIGINAL FIXTURE WAS ATTACHED.
•
BEFORE DISCARDING THE CARTON DOUBLE CHECK THE
PACKAGING TO MAKE SURE ALL PARTS HAVE BEEN FOUND.
•
THIS FIXTURE WAS DESIGNED TO BE MOUNTED TO AN
OCTAGON OUTLET BOX. THE BOX MUST BE SECURELY
MOUNTED TO THE STRUCTURE OF THE BUILDING.
INSTALLATION
STEP 1. Pull the wires out from the outlet box, and install
mounting plate onto the outlet box using the (2)
mounting screws. Strip the Fixture wire ends 5/8”
STEP 2. Fasten bare ground wire to ground wire from the wall
outlet box (usually green or copper color) or connect
ground wire to green screw on the mounting plate.
STEP 3. Connect the neutral (white) fixture wire coming from the
fixture base to neutral (usually white) outlet wire. Fasten
both wires together with a plastic wire nut and tightly
wrap the wire nut with electrical tape.
STEP 4. Repeat the previous step with the hot (black wires).
Make sure there are no exposed wires or strands that
could cause a dangerous short circuit.
FAILURE TO CONNECT THE APPROPRIATE WIRES
CORRECTLY COULD RESULT IN SERIOUS INJURY OR
D
EATH!
STEP 5. Carefully place connections back into the outlet box
STEP 6. Place canopy over the mounting plate and secure with
Set Screws
STEP 7. Install the lamp(s). The fixture is rated for 60 watt type A
lamp.
DO NOT EXCEED RECOMMENDED WATTAGE
STEP 8. Unscrew Screw checker and slide the glass cover up
STEP 9. Tilt the glass shade slightly and lift up so the glass
support is inside the glass. Straighten out the Glass
shade and rest on glass support.
STEP 10. Slide down the glass cover and screw the screw checker
back onto the arm.
STEP 11. Restore power to the circuit at breaker or fusebox.
DIMMING
The fixture can be controlled by a wall dimming device. Only use
triac/electronic dimmer. Make sure carton is marked for use with LED
compact fluorescent-incandescent light source only. These can be
provided by your local electrical distributor, home center, or
hardware store.
CLEANING
Please clean with a soft, dry cloth ONLY! Do not use cleaning products.