Instructions / Assembly
Table Of Contents
- ,H285101,
- GENERAL
- GENERAL
- INSTALLATION
- INSTALLATION
- STEP 1. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws.
- STEP 1. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws.
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 2. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 3. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- STEP 4. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SEROIUS INJURY OR DEATH!
- STEP 5. Carefully place connections back into the outlet box
- STEP 5. Carefully place connections back into the outlet box
- STEP 5. Carefully place connections back into the outlet box
- STEP 6. Place Back plate over the mounting plate and secure with set screws.
- STEP 6. Place Back plate over the mounting plate and secure with set screws.
- STEP 6. Place Back plate over the mounting plate and secure with set screws.
- STEP 7. Install the lamp(s). The fixture is rated for 40 watt type B lamp.
- STEP 7. Install the lamp(s). The fixture is rated for 40 watt type B lamp.
- STEP 7. Install the lamp(s). The fixture is rated for 40 watt type B lamp.
- DO NOT EXCEED RECOMMENDED WATTAGE!
- DO NOT EXCEED RECOMMENDED WATTAGE!
- DO NOT EXCEED RECOMMENDED WATTAGE!
- STEP 8. Restore power to the circuit at breaker or fuse box.
- STEP 8. Restore power to the circuit at breaker or fuse box.
- STEP 8. Restore power to the circuit at breaker or fuse box.
- DIMMING
- DIMMING
- CLEANING
- CLEANING
- ASSEMBLY AND MOUNTING DIAGRAM
- ASSEMBLY AND MOUNTING DIAGRAM
- WIRE NUT/TAPING DIAGRAM
- WIRE NUT/TAPING DIAGRAM
- H285 101 M48
- GENERALITÉ
- GENERALITÉ
- INSTALLATION
- INSTALLATION
- PAS 3. Relier le fil neutre (blanc) venant de la base du dispositif au fil neutre (généralement blanc) de la boîte de dérivation. Relier les deux fils entre eux à l’aide d’un serre-câble en plastique et envelopper le serre-câble de ruban isolant bien ...
- PAS 3. Relier le fil neutre (blanc) venant de la base du dispositif au fil neutre (généralement blanc) de la boîte de dérivation. Relier les deux fils entre eux à l’aide d’un serre-câble en plastique et envelopper le serre-câble de ruban isolant bien ...
- RÈGLAGE D’INTENSITÉ
- RÈGLAGE D’INTENSITÉ
- NETTOYAGE
- NETTOYAGE
- SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
- SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
- SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
- SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
H285101 LUPE SCONCE
www.hudsonvalleylighting.com/mitzi | #mymitzi
SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
PLAQUE ARRIÈRE
ÉCROU RÉGLABLE
AMPOULE
BOÎTE DE
DÉRIVATION
PLAFOND
VIS DE MONTAGE
PLAQUE DE MONTAGE
VIS DE FIXATION
RUBAN ISOLANT
CONNECTEUR APPROUVÉ
(BORNE DE RACCORDEMENT)
VIS DE MISE À TERRE