- Mitsumi Electronics Computer Hardware User Manual

ManualsBrandsMitsumi electronic ManualsComputer HardwareFX2N

HARDWARE MANUAL

SERIES PROGRAMMABLE CONTROLLERS

Summary of content (130 pages)

PAGE 1
HARDWARE MANUAL FX2N SERIES PROGRAMMABLE CONTROLLERS
PAGE 2
FX2N Series Programmable Controllers ENG Foreword • • • FRE Préface • • • GER • • Dieses Handbuch enthält Texte, Abbildungen und Erläuterungen zur korrekten Installation und Bedienung der FX2N-SPS und sollte vor einer Installation oder einem Einsatz des Gerätes gelesen werden. Die Inhalte müssen verstanden sein.
PAGE 3
FX2N Series Programmable Controllers FX2N Series Programmable Controllers Hardware Manual Manuel du matériel Hardware-Handbuch Manuale hardware Manual de Hardware Manual number : JY992D66301 Manual revision : J Date : March 2003 i
PAGE 4
FX2N Series Programmable Controllers Guidelines for the safety of the user and protection of the FX2N ENG This manual provides information for the installation and use of the FX2N. The manual has been written to be used by trained and competent personnel.
PAGE 5
FX2N Series Programmable Controllers Directives de sécurité pour l’utilisateur et mesures de protection pour les API de la série FX2N. ) FRE Le présent manuel contient des informations concernant l’installation et l’utilisation des API de la série FX2N. Ce manuel a été établi à l’intention d’un personnel formé et compétent.
PAGE 6
FX2N Series Programmable Controllers Sicherheitsrichtlinien für den Anwender und Schutzmaßnahmen für die FX2N-SPS ) GER Dieses Handbuch enthält Informationen zur Installation und zum Einsatz der FX2N-SPS. Das Handbuch wurde für geschultes und kompetentes Personal erstellt.
PAGE 7
FX2N Series Programmable Controllers Direttive di sicurezza per l’utente e misure di sicurezza per il PLC FX2N ) ITL Il presente manuale contiene informazioni per l’installazione e l’impiego del PLC FX2N. Il manuale è destinato a personale addestrato e competente.
PAGE 8
FX2N Series Programmable Controllers Instrucciones de seguridad para el usuario y medidas de protección para la unidad PLCFX2N ) ESP Este manual comprende las informaciones correspondientes para la instalación y el uso de la unidad PLC-FX2N . El manual ha sido elaborado para un empleo por personal competente y capacitado.
PAGE 9
FX2N Series Programmable Controllers ENG The following FX2N PLC module conform to the identified standards; FRE Les modules suivants de la série FX2N sont conformes aux normes et critères d'homologation mentionnés. GER Die folgenden Module der FX2N-Serie stimmen mit den aufgeführten Normen und Zulassungskriterien überein. ITL ESP I seguenti moduli della serie FX2N sono conformi alle norme ed ai criteri di certificazione esposti.
PAGE 10
FX2N Series Programmable Controllers viii
PAGE 11
FX2N Series Programmable Controllers FRE ENG GER ITL ESP 1 Introduction Introduction Einleitung Introduzione Introducción 1 2 Terminal Layouts Occupation des bornes Klemmenbelegungen Assegnazione Ocupaciones dei morsetti de bornas 2 3 Installation Notes Installation Installation Installazione 3 4 Power supply Alimentation en tension Spannungsversorgung Alimentazione Alimentación della tensione de tensión 4 5 Inputs Entrées Eingänge Ingressi Entradas 5 6 Outputs Sortie
PAGE 12
FX2N Series Programmable Controllers ENG Table of Contents Guidelines of Safety................................. ii 6. Outputs ............................................ 6-1 6.1 1.1 1.2 1.3 1.4 1.5 Unit Accessories.................................... 1-9 World Specification................................ 1-9 Model name......................................... 1-10 Serial number ...................................... 1-11 Configuration ....................................... 1-12 1.5.
PAGE 13
FX2N Series Programmable Controllers FRE Sommarire Directives de sécurité ..............................iii 6. Sorties ............................................. 6-1 6.1 1. Introduction ......................................1-1 1.1 1.2 1.3 1.4 1.5 Accessoires d’un appareil...................... 1-9 Version internationale............................ 1-9 Designation des types d'appareils. ...... 1-10 Numéro de serie .................................. 1-11 Construction du système .....................
PAGE 14
FX2N Series Programmable Controllers GER Inhaltsverzeichnis Sicherheitsrichtlinien............................... iv 6. Ausgänge ........................................ 6-1 6.1 1. Einleitung .........................................1-1 1.1 1.2 1.3 1.4 1.5 Zubehör einer Geräteeinheit.................. 1-9 Weltweite Ausführung............................ 1-9 Geratetypenbezeichnung .................... 1-10 Seriennummer ..................................... 1-11 Systemaufbau..............................
PAGE 15
FX2N Series Programmable Controllers ITL Indice Direttive di sicurezza................................ v 6. Uscite .............................................. 6-1 6.1 1.1 1.2 1.4 1.5 Accessori di un apparecchio.................. 1-9 Esecuzione internazionale..................... 1-9 Numero di serie ................................... 1-11 Struttura del sistema............................ 1-12 1.5.1 Regole base sulla struttura del sistema ............................................
PAGE 16
FX2N Series Programmable Controllers ESP Contenido Instrucciones de Seguridad .................... vi 5.2 5.2.1 1. Introducción......................................1-1 1.1 1.2 1.3 1.3 1.4 1.5 Accesorios de una unidad de producción ........................................ 1-9 Modelo internacional ............................. 1-9 Designacion del tipo de unidad ........... 1-10 Designazione dei modelli..................... 1-10 Número de serie ..................................
PAGE 17
Introduction 1 FX2N Series Programmable Controllers 1. Introduction ENG Introduction 1. FRE This ma nu al covers the h ardware insta lla tio n instructions for the following programmable logic controller (PLC) product ranges; GER - FX2N base and extension units - FX2N extension and special function blocks Einleitung - FX2N-Grund-und Erweiterungsgeräte - FX2N-Erweiterungs- und Sondermodule Introducción 1.
PAGE 18
FX2N Series Programmable Controllers Table 1.
PAGE 19
FX2N Series Programmable Controllers Figure 1.1: 90(3.55") ENG ☞ Dimensioned unit GER ☞ Abmessungen ESP ☞ Dimensiones Introduction 1 FRE ITL ☞ Dimensions ☞ Dimensioni 350(13.78") 87(3.43") 130(5.12") 1 DIN rail: 35mm(1.37") 2 3 UNITS: mm(inches) Figure 1.2: 90(3.55") ENG FRE GER ITL ESP ☞ ☞ ☞ ☞ ☞ Extension block dimensions Dimensions des modules d’extension Abmessungen der Erweiterungsmodule Dimensioni dei moduli di ampliamento Dimensiones de los módulos de ampliación 70(2.76") 40(1.
PAGE 20
FX2N Series Programmable Controllers Table 1.
PAGE 21
FX2N Series Programmable Controllers Table 1.
PAGE 22
FX2N Series Programmable Controllers Introduction 1 ENG *1 Internal 24V DC *2 FX2N-10PG inputs and outputs need to be supplied from external power supply. For power consampution of the input and output, please see FX2N-10PG User’s Manual. *3 FX2N series PLC cannot connect together with an FX2N-32ASI-M and FX2N-16CCL-M. An FX2N-32ASI-M module cannot be attached to an FX2N series PLC that is using an FX 2N-16CCL-M module. Only one FX 2N32ASI- M module can be connected to the PLC.
PAGE 23
FX2N Series Programmable Controllers Introduction 1 GER *1 Interne 24 V DC *2 Die Ein- und Ausgänge des FX2N-10PG müssen von extern mit Spannung versorgt werden. Angaben zur Stromaufnahme der Ein- und Ausgänge enthält das Handbuch zum FX2N-10PG. *3 In einer SPS der FX2N-Serie kann kein FX2N32ASI-M gemeinsam mit einem FX2N-16CCLM betrieben werden. Ein FX2N-32ASI-M kann nicht an SPS der FX2N-Serie angeschlossen werden, in der ein FX2N-16CCL-M verwendet wird.
PAGE 24
FX2N Series Programmable Controllers Introduction 1 ESP *5 El valor depende del ajuste del interruptor (32, 64, 96 ó 128 direcciones). La cantidad de módulos maestros a instalar está sin embargo limitada por el rango de direcciones de la CPU. La suma de las direcciones de entrada/salida de los aparatos base, de los aparatos de ampliación, de los módulos m a e s t ro s y lo s m ó d u lo s e s p e c i a le s ( 8 entradas y salidas ocupadas) no puede ser mayor a 256.
PAGE 25
FX2N Series Programmable Controllers 1.1 Introduction 1 Unit Accessories ENG Unit Accessories 1.1 Accessoires d’un appareil FRE Each powered extension unit comes with: 1 I/O label kit and a 55mm (2.17 inch) extension cables. Each extension and special function block comes with an I/O label kit. GER Zubehör einer Geräteeinheit 1.1 Lieferumfang eines spannungsversorgten Erweiterungsgerätes: 1 E-/A-Aufklebersatz und die beiden E r we i te r u n g s k a b e l m i t 5 5 m m L ä n g e.
PAGE 26
FX2N Series Programmable Controllers 1.3 Introduction 1 Model name ENG Model name 1.3 FRE Designation des types d'appareils. 1.3 GER Gerätetypenbezeichnung 1.3 ITL Designazione dei modelli. ESP Designacion del tipo de unidad 1.3 Table 1.9: ENG ☞ Model table GER ☞ Typenbeschreibung ESP ☞ Descripción del tipo REF ENG A) PLC type, FX, FX0N, FX2N Série d’API: FX, FX0N, FX2N B) Total number of I/O channels FX-8AV = 8 ch. FX2N-64= 64ch. FX-16EX = 16ch.
PAGE 27
FX2N Series Programmable Controllers Introduction 1 Table 1.10: Model CE UL FX2N-**MR-DS, **MT-DSS ✔ ✔ FX2N-**M*-E/UL ✘ ✔ FX2N-16EYS ✘ ✔ Figure 1.3: 1.4 ENG FRE GER ITL ESP ☞ ☞ ☞ ☞ ☞ 1 Model name Désignation des types d’appareils. Typenbezeichnung Modello. Designación del tipo F X 2 N - 1 6 M R - E S / U L A ) F ) B ) E ) C ) D ) 2 3 Serial numbers ENG Serial number 1.4 FRE Numéro de serie 1.4 GER Seriennummer 1.4 ITL Numero di serie 1.
PAGE 28
FX2N Series Programmable Controllers 1.5 Introduction 1 Configuration ENG Configuration 1.5 ITL Struttura del sistema 1.5 FRE Configuration du système 1.5 ESP Configuración del sistema 1.5 GER Systemaufbau 1.5 Figure 1.
PAGE 29
FX2N Series Programmable Controllers Table 1.
PAGE 30
FX2N Series Programmable Controllers Table 1.
PAGE 31
FX2N Series Programmable Controllers ESP Introduction 1 Reglas básicas para la configuración del sistema 1.5.1 ITL Regole base sulla struttura del sistema1.5.1 Sono consentiti max. 8 moduli speciali per ogni sistema. Verificate il carico sul BUS a 5 volt. Il valore di consumo di corrente dei moduli speciali è riportato sulla alle tabelle da 1.5 a 1.7. La corrente max. consentita è riportata sulla tabella in basso. Verificate il carico della tensione di servizio 24V.
PAGE 32
FX2N Series Programmable Controllers Introduction 1 Table 1.17: L COM X0 X2 24+ X1 N X4 X5 X6 X7 X10 POWER IN PROG.E Y0 COM1 Y2 Y3 Y4 Y6 COM2 Y5 Y7 Y10 COM3 20 21 22 23 24 25 26 27 Y14 COM4 Y15 Y20 Y22 Y24 Y26 COM5 Y21 Y23 Y25 Y27 1 2 3 4 5 6 0 1 2 3 4 5 6 3 7 OUT 0 1 2 3 4 5 6 7 POWER No. 0 OUT 0 1 2 3 4 5 6 7 .A .B UPDN PRESET IN 0 1 2 3 4 5 6 7 + + V- - DC24V V+ - CH1 I- I+ COMA.A24 COMB.B24 COMP SG .A5 .A12 .B5 .
PAGE 33
FX2N Series Programmable Controllers 2. ENG Terminal layouts 2 Terminal layouts Terminal layouts 2. The following selection of terminal layouts are taken from the FX2N product range. Note: All layouts are schematic only and are only intended to aid in the creation of wiring diagrams. Some units over 80 I/O do not conveniently fit on the page, hence the terminal rails have been split to suit. FRE GER Occupation des bornes 1 2.
PAGE 34
FX2N Series Programmable Controllers 2.1 Terminal layouts 2 Relay output, 24V DC input MPU's - Main Processing Unit (base units) ENG Relay out, 24V DC input MPU’s - Main Processing Unit (base units) 2.1 FRE Appareils de base avec sorties de relais et entrées 24V CC 2.1 GER Grundgeräte mit Relais-Ausgängen und DC 24V-Eingängen 2.1 ITL Apparecchi base con uscite relè e ingressi 24V DC 2.1 ESP Unidades base con Salidas de relé y Entradas de 24V CC 2.
PAGE 35
FX2N Series Programmable Controllers 2.2 Terminal layouts 2 Transistor output, MPU's - (base units) ENG Transistor output, MPU’s - (base units) 2.2 FRE Appareils de base avec sorties de transistor 2.2 GER Grundgeräte mit Transistor-Ausgängen transistor 2.2 ITL Apparecchi base con uscitea 2.2 ESP Unidades base con Salidas transistorizadas 2.
PAGE 36
FX2N Series Programmable Controllers 2.3 Terminal layouts 2 Powered extension units ENG Powered extension units 2.3 FRE Appareils d’extension alimentés en tension 2.3 GER Spannungsversorgte Erweiterungsgeräte 2.3 ITL Apparecchi di ampliamento con alimentazione di tensione 2.3 ESP Unidades de ampliación con alimentación de tensión 2.
PAGE 37
FX2N Series Programmable Controllers 2.5 Terminal layouts 2 FX0N Extension blocks ENG FX0N Extension blocks 2.5 FRE Modules d'extension FX0N 2.5 GER Erweiterungsmodule FX0N 2.5 ITL Moduli di ampliamento FX0N 2.5 ESP Modulos de ampliacion FX0N 2.
PAGE 38
FX2N Series Programmable Controllers 2.6 Terminal layouts 2 AC 110V Input, MPUs - (base units) ENG AC 110V Input, MPUs - (base units) 2.6 FRE Appareils de base avec entrées 110V CA 2.6 GER Grundgeräte mit AC 110V-Eingängen 2.6 ITL Apparecchi base con ingressi 110V CA 2.6 ESP Unidades base con Entradas de 110V CA 2.
PAGE 39
Installation 3 FX2N Series Programmable Controllers 3. ENG Installation Installation 3. FRE The installation of FX2N products has been designed to be safe and easy. When the products associated with this manual are used as a system or individually, they must be installed in a suitable enclosure. The enclosure should be selected and installed in accordance to the local and national standards. GER Installation ESP Instalación 3.
PAGE 40
FX2N Series Programmable Controllers 3.1 Installation 3 Product outline ENG Product outline 3.1 ITL Descrizione dell’apparecchio 3.1 FRE Description de l’appareil 3.1 ESP Descripción de las unidades 3.1 GER Gerätebeschreibung 3.1 Figure 3.
PAGE 41
FX2N Series Programmable Controllers Table 3.1: Installation 3 ENG ☞ Feature table FRE ☞ Vue d’ensemble des composants GER ☞ Übersicht der Komponenten ITL ☞ Componenti ESP ☞ Vista de conjunto de los componentes REF ENG FRE GER ITL ESP A DIN rail 35mm (1.
PAGE 42
FX2N Series Programmable Controllers 3.2 ENG Installation 3 RUN/STOP Control RUN/STOP Control 3.2 RUN or STOP of the FX2N can be controlled by: ➀ The RUN/STOP switch mounted next to the programming port. ➁ A standard input (X0 to X17; X0 to X7 for FX2N-16M✩ units) defined by the system parameters. ➂ Remotely from a personal computer or other programming peripheral. Note: GER The FX2N RUN/STOP switch ➀ works in parallel with the RUN-input terminal ➁. Please refer to the table below.
PAGE 43
FX2N Series Programmable Controllers Installation 3 Commande Run/Stop FRE 3.2 La fonction RUN ou STOP de la FX2N peut être commandée: ➀ au commutateur RUN/STOP installé à côté du port de programmation; ➁ au moyen d’une entrée standard (X0 à X17; X0 à X7 pour des unités FX2N-16M✩) définie par des paramètres système; 1 ➂ à distance, à partir d’un micro-ordinateur ou d’un autre périphérique de programmation. L’interrupteur RUN-STOP du FX2N ➀ fonctionne parallèlement à la borne RUN ➁.
PAGE 44
FX2N Series Programmable Controllers 3.3 Installation 3 General specifications ENG General specifications 3.3 ITL Specifica generale 3.3 FRE Caractéristiques générales 3.3 ESP Especificación general 3.3 GER Umgebungsbedingungen 3.3 Table 3.
PAGE 45
FX2N Series Programmable Controllers Installation 3 ENG ☞ General specifications GER ☞ Umgebungsbedingungen ESP ☞ Especificación general Table 3.
PAGE 46
FX2N Series Programmable Controllers 3.4 ENG Installation 3 PLC mounting arrangements PLC mounting arrangements 3.4 FRE To prevent a rise in temperature, mount the units to walls. Never mount them to the floor or ceiling of an enclosure. GER Figure 3.2 Single row arrangement Figure 3.3 Double row arrangement using extension cable FX 0N -65EC /FX 0N 30EC(650mm (25.59 inches) /300mm (11.81 inches); supplied separately). Montage der SPS 3.4 Montage de l’API 3.
PAGE 47
FX2N Series Programmable Controllers ENG Installation 3 Caution • Units should not be installed in areas subject to the following conditions: excessive or conductive dust, corrosive or flammable gas, moisture or rain, excessive heat, regular impact shocks or excessive vibration. • Take special care not to allow debris to fall inside the unit during installation e.g. cut wires, shavings etc. Once installation is complete remove the protective paper band to prevent overheating.
PAGE 48
FX2N Series Programmable Controllers ITL ESP Installation 3 Attenzione • Gli apparecchi non devono essere installati in ambienti di lavoro in cui si possono riscontrare le seguenti condizioni ambientali: polvere eccessiva o conduttrice di corrente, gas aggressivi, umidità o pioggia, calore eccessivo, urti continui o vibrazioni eccessive. • Proteggete l’apparecchio durante l’installazione dalla penetrazione di particelle conduttrici di corrente (ad es. resti di fili, trucioli metallici ecc.).
PAGE 49
FX2N Series Programmable Controllers 3.5 ENG Installation 3 DIN rail mounting DIN rail mounting 3.5 FRE Units can be ‘snap’ mounted on to 35mm (1.37 inch) DIN rail. To release the unit from a DIN rail mount; pull the spring loaded DIN clips away from the rail. Once the spring clips are clear, slide the unit up and off. Les a ppar ei ls p euve nt êtr e m ont és “ par encrantement” sur un rail DIN (35 mm).
PAGE 50
FX2N Series Programmable Controllers 3.6 ENG Installation 3 Direct mounting Direct mounting 3.6 FX2N-10GM and FX2N-20GM can only mount on the DIN rail. GER Direkte Montage 3.6 Montage direct FRE Le FX2N-10GM et le FX2N-20GM peuvent être montés seulement sur un rail DIN. Montaggio diretto ITL Das FX 2N -10GM und das FX 2N -20GM können nur auf einer DIN-Schiene montiert werden. ESP Montaje directo 3.6 3.6 Il FX2N-10GM e il FX2N-20GM possono essere montati solo su binario DIN. 3.
PAGE 51
FX2N Series Programmable Controllers ENG GER ESP ☞Hole positions FRE ☞ Positions des trous ☞Lochpositionen ITL ☞ Posizioni dei fori ☞Posiciones de los agujeros UNIT mm inches ± 0.2 ± 0.01 FX2N-8AD 67 90(3.55") D = W-8mm(0.32") 2.64 E = W-24.5mm(0.97") FX2NC-232ADP, FX2NC-485ADP 65.5 1 98(3.86") Table 3.4: Installation 3 2.58 2 F = W-10mm(0.40") 60 2.37 FX2N-16CCL-M 75 2.96 10 (0.40") FX0N-16E✩ 75(2.96") D W 16.1(0.64") 3 4 W F ∅ = 4.5mm (0.17") 19.1(0.76") 7(0.28") 74(2.
PAGE 52
FX2N Series Programmable Controllers 3.8 ENG Installation 3 Extension Board Installation Extension Board Installation 3.8 FRE To install a special function extension board on the left side of the FX2N MPU: Installation de la carte d’extension 3.8 Pour installer une car te d’extension à fonctions spéciales du côté gauche de la MPU FX2N, il faut: ➀ Remove the top cover of the FX2N.
PAGE 53
FX2N Series Programmable Controllers ESP Instalación de la tarjeta de extensión3.8 Installation 3 Figure 3.4: Para instalar una tarjeta de extensión funcional especial en el lado izquierdo del FX 2N MPU se debe: ➃ ➀ Quitar la tapa del FX2N. 1 ➁ Fijar la tarjeta al conector y colocar correc tamen te sobre los agu jeros para roscar. ➂ Fijar la tarjeta a la unidad base mediante los ➂ ➀ X3 tornillos de atornillamiento directo M3.
PAGE 54
FX2N Series Programmable Controllers 3.9 ENG Installation 3 Extension Units/Blocks Installation Extension Units/Blocks Installation 3.9 FRE ➀ Remove the extension bus cover. ➀ Enlever le couvercle du bus d'extension ➁ Install extension cable. ➁ Raccorder le câble d'extension ➁' Remove extension cable. ➁' Retirer le câble d'extension ➂ Install the extension bus cover.
PAGE 55
FX2N Series Programmable Controllers 4. ENG Wiring techniques 4 Wiring techniques Wiring techniques 4. The wiring of FX 2N products has been designed to be safe and easy. If during the installation of these product or associated products concern is felt, please contact a professional electrician who is trained to the local and national standards applicable to the installation site. FRE Raccordement électrique 4. Les appareils FX 2N ont été conçus de manière à assurer un câblage simple et sûr.
PAGE 56
FX2N Series Programmable Controllers FRE GER Wiring techniques 4 Instructions relatives au cablage 4.1 • Ne transmettez pas ensemble des signaux d’entrée et de sortie sur un même câble multiconducteur ou par la même ligne de signalisation. • Ne posez pas de câble de signalisation E/S à proximité de câbles de puissance ou dans un caniveau à câble commun. Les câbles à basse tension doivent être sûrement séparés ou isolés des câbles à haute tension.
PAGE 57
FX2N Series Programmable Controllers ITL ESP Wiring techniques 4 Avvertenze per il cablaggio 4.1 • Non mettete insieme i segnali degli ingressi e delle uscite in un cavo multipolare o nella stessa linea di controllo. • Non posate i cavi dei segnali I/O in prossimità dei cavi di potenza o in una canalina comune. I cavi dibassa tensione devono essere separati o isolati in modo sicuro ai cavi di alta tensione.
PAGE 58
FX2N Series Programmable Controllers 4.2 ENG Wiring techniques 4 Termination at screw terminals Termination at screw terminals 4.2 Terminal screws should be tightened to between 0.5 and 0.8 N·m. Terminal screws must be secured to prevent a loose connection thus avoiding a malfunction. The terminal screws for the FX2N Series PLC are M3.0. However, the terminal screws for the FX0N-32NT-DP and Terminal Blocks are M3.5.
PAGE 59
FX2N Series Programmable Controllers ESP Wiring techniques 4 Conexión de bornas roscadas Los bornes atornillados deben apretarse con un momento de torque de 0,5 a 0,8 Nm. Debido a bornes atornillados mal torqueados pueden acontecer fallas de función. Los bornes atornillados de la serie FX2N poseen un tornillo M3, el FX0N-32NT-DP así como los módulos de conexión poseen una rosca M3,5. Utilice para la conexión final los manguitos de cable con conexión de apriete como se muestra en la figura.
PAGE 60
FX2N Series Programmable Controllers Figure 4.4: ENG FRE GER ITL ESP ☞ ☞ ☞ ☞ ☞ Wiring techniques 4 Crimp Terminals for M3.5 Screws Cosse de câble avec raccordement serti pour vis M3,5 Kabelschuhe mit Quetschanschluss für M3,5-Schrauben Capocorda con collegamento a scatto per viti M3,5 Manguitos de cable con conexión de apriete para tornillos M3,5 φ 3.7 (0.15") 6.8 mm (0.27" ) or less 6.8 mm (0.27") or less φ 3.7 (0.15") 6.0 (0.24") mm or more Figure 4.
PAGE 61
FX2N Series Programmable Controllers 4.3 ENG Wiring techniques 4 Power supply Power supply 4.3 When wiring AC supplies the ‘Live’ cable should be connected to the ‘L’ terminal and the ‘Neutral’ cable should be connected to the ‘N’ terminal. When wiring DC supplies the ‘positive’ cable should be connected to the ‘+’ terminal and the negative cable should be connected to the ‘-’ terminal. On no account should the power supply terminals/cables be conected to any other 1 terminal on the unit.
PAGE 62
FX2N Series Programmable Controllers GER Wiring techniques 4 Spannungsversorgung 4.3 Beim Anschluß einer Wechselspannung (AC) müssen der L-Leiter an die L-Klemme und der N-Leiter an die N-Klemme angeschlossen werden. Beim Anschluß einer Gleichspannung (DC) müssen der positive Leiter an die (+)-Klemme und der negative Leiter an die (-)-Klemme angeschlossen werden. Der Anschluß der Spannungsversorgung darf auf keinen Fall an einer anderen Klemme des Gerätes erfolgen.
PAGE 63
FX2N Series Programmable Controllers ESP Wiring techniques 4 Alimentación de tensión 4.3 Al conectar una tensión alterna (CA), los conductores L se tienen que conectar en la borna L y el conductor N en la borna N. En la conexión de una tensión continua (CC), el conductor positivo se tiene que conectar en la borna (+) y el conductor negativo en la borna (-). La conexión de la unidad de alimentación de tensión no se debe efectuar en ningún caso en ninguna otra borna de la unidad.
PAGE 64
FX2N Series Programmable Controllers Table 4.
PAGE 65
FX2N Series Programmable Controllers Wiring techniques 4 ENG ☞ Power connection diagram GER ☞ Spannungsanschluß ESP ☞ Conexión de tensión Table 4.2: REF ENG FRE ☞Raccordement de la tension ITL ☞Allacciamento della tensione FRE GER ITL ESP 1 Grounding (100Ω or less) Mise à la terre (100Ω maxi) Erdung (max. 100 Ω) Terra (mass. 100 Ω) Puesta a tierra (máx.
PAGE 66
FX2N Series Programmable Controllers 4.4 ENG Wiring techniques 4 Earthing/Grounding Earthing/Grounding 4.4 Use a cable at least 2mm2 (AWG14) to ground equipment. Ground resistance must be less than 100 Ω. Note that the ground cable must not be connected to the same ground as the power circuits. FRE Mise à la terre 4.4 Pour le raccordement à la terre, utilisez des lignes d’une section minimale de 2 mm2 (AWG14). La résistance de terre doit être inférieure à 100 Ω.
PAGE 67
FX2N Series Programmable Controllers 4.5 ENG Wiring techniques 4 Service power supply Service power supply 4.5 If the system being installed uses the service supply from both the PLC and a powered extension block , then the 0V terminals should be linked. FRE • DO NOT however, link the 24V terminals. • NEVER connect an external power supply to the PLC’s 24V terminal. • External DC supplies should not compromise the IEE Separated Extra Low Voltage (SELV) aspects of the FX2N products.
PAGE 68
FX2N Series Programmable Controllers Table 4.
PAGE 69
FX2N Series Programmable Controllers 5. Inputs 5 Inputs 5.1 ENG GER ESP Table 5.1: Inputs 5. Entrées 5. Eingänge 5. Ingressi 5. Entradas 5. 24V DC input specifications 24V DC input specifications 5.1 Technische Daten der Eingänge für 24 V DC FRE 5.1 ITL Datos técnicos de las entradas para 24 V CC 5.1 Caractéristiques techniques des entrées pour 24 V CC 1 5.1 Dati tecnici degli ingressi per 24 V DC 5.
PAGE 70
FX2N Series Programmable Controllers 5.1.1 Inputs 5 Typical wiring ENG Typical wiring 5.1.1 FRE Exemple de câblage 5.1.1 GER Verdrahtungsbeispiel 5.1.1 ITL Ejemplo de cableado 5.1.1 ESP Esempio di cablaggio 5.1.1 Figure 5.1: 2 ☞ ☞ ☞ ☞ ☞ ENG FRE GER ITL ESP Source (positive input connection, negative S/S) Source (émetteur) (pôle positif) Source (plusschaltend) Source (comando positivo) Source (conexión de positivo) PNP 3 3 3 1 24V 0V S/S X0 X1 X2 X3 S/S X0 X1 4 Figure 5.
PAGE 71
FX2N Series Programmable Controllers Table 5.2: ENG ☞ Item check GER ☞ Positionsbeschreibung ESP ☞ Descripción de posición Inputs 5 FRE ☞ Description du poste ITL ☞ Descrizione della posizione REF.
PAGE 72
FX2N Series Programmable Controllers Inputs 5 ENG External supply The example shown right, uses an external power supply to activate the inputs FRE Alimentation externe L’exemple de droite montre l’utilisation d’une tension de service externe pour activer les entrées. GER Externe Versorgung Das rechte Beispiel zeigt den Einsatz einer externen Versorgungsspannung zu Aktivierung der Eingänge.
PAGE 73
FX2N Series Programmable Controllers 5.1.4 ENG Inputs 5 Resistors and inputs connected in parallel Resistors and inputs connected in parallel 5.1.4 Résistanceetentréemontéesenparallèle5.1.4 FRE R é s i s t a n c e p a ra l l è l e R p : F X 2 N = 1 5 k Ω. U n e résistance Rb complémentaire doit être mise en place lorsque Rp est inférieur à ces valeurs (voir équation 1 pour les caculs). Autre possibilité: courant de fuite autorisé FX2N = 1.5 mA.
PAGE 74
FX2N Series Programmable Controllers 5.2 ENG Inputs 5 AC 110V Input, MPUs AC 110V Input, MPUs 5.2 GER Grundgeräte mit AC 110V-Eingängen5.2 ESP Unidades bas con Entradas de 110V CA 5.2 Table 5.3: ENG FRE GER ITL ESP FRE Appareils de base avec entrées 110V CA 5.2 ITL Apparecchi base con ingressi 110V AC 5.
PAGE 75
FX2N Series Programmable Controllers 5.2.1 Inputs 5 110V AC input specifications 110V AC input specifications ENG 5.2.1 Technische Daten der Eingänge für AC 110 V 5.2.1 GER FRE ITL Caractéristiques techniques des entrées pour 110 V CA 5.2.1 Dati tecnici degli ingressi per 110 V AC5.2.1 1 Datos técnicos de las entradas para 110 V CA 5.2.1 ESP Table 5.
PAGE 76
FX2N Series Programmable Controllers 5.2.2 Inputs 5 Typical wiring ENG GER ESP Typical wiring 5.2.2 Verdrahtungsbeispiel 5.2.2 Ejemplo de cableado 5.2.2 FRE ITL ENG ☞ Typical wiring GER ☞ Verdrahtungsbeispiel ESP ☞ Ejemplo de cableado Figure 5.5: FRE ITL Exemple de câblage 5.2.2 Esempio di cablaggio 5.2.2 ☞ Exemple de câblage ☞ Esempio di cablaggio 2 2 1 L N COM X0 X1 X2 X3 COM 3 Table 5.5: ENG GER ESP ☞Item check ☞Positionsbeschreibung ☞Descripción de posición REF.
PAGE 77
FX2N Series Programmable Controllers 5.2.3 ENG Inputs 5 Programming caution Programming caution 5.2.3 FRE When using 110V AC units, high speed counter and interrupt routines are not suitable for use due to the long ‘ON/OFF’ times. The following instructions are also not suitable.
PAGE 78
FX2N Series Programmable Controllers Inputs 5 MEMO 5-10
PAGE 79
Outputs 6 FX2N Series Programmable Controllers 6. Outputs 6.1 Outputs 6. Sorties 6. Ausgänge 6. Uscite 6. Salidas 6. Relay output specification ENG Relay output specification 6.1 FRE Caractéristiques techniques des sorties des relais 6.1 GER Technische Daten der Relais-Ausgänge 6.1 ITL Dati tecnici delle uscite a relè 6.1 ESP Datos técnicos de las salidas de relé 6.1 1 2 3 Table 6.
PAGE 80
FX2N Series Programmable Controllers Table 6.
PAGE 81
FX2N Series Programmable Controllers 6.1.1 ENG Outputs 6 Reliability tests Reliability tests 6.1.1 The test results in table 6.2 were gathered from a 1 sec ON/OFF test cycle. Please note that the over current induced by in-rush greatly reduces the relay contacts service life. The rated life for an inductive AC load such as a contactor or solenoid valve is 500,000 operations at 20VA. FRE Contrôles de fiabilité 6.1.1 Les résultats du contrôle sont indiqués dans le tableau 6.
PAGE 82
FX2N Series Programmable Controllers 6.1.2 Outputs 6 Relay output example ENG FRE GER ITL ESP Relay output example 6.1.2 Exemple d’un câblage de sortie de relais 6.1.2 Beispiel einer Relais-Ausgangsbeschaltung 6.1.2 Esempio del cablaggio di uscita di un relè 6.1.2 Ejemplo de una conexión de salida de relé 6.1.2 Figure 6.
PAGE 83
FX2N Series Programmable Controllers 6.2 Outputs 6 Triac (SSR) output specifications ENG Triac (SSR) output specifications 6.2 FRE Caractéristiques techniques des sorties triac (SSR) 6.2 GER Technische Daten der Triac(SSR)-Ausgänge 6.2 ITL Dati tecnici delle uscite triac(SSR) 6.2 ESP Datos técnicos de las salidas Triac(SSR) 6.2 Table 6.
PAGE 84
FX2N Series Programmable Controllers Table 6.
PAGE 85
FX2N Series Programmable Controllers 6.2.1 ENG FRE GER ITL ESP Outputs 6 In-rush currents In-rush currents 6.2.1 These currents should be kept as low as possible. The root mean square (Ιrms) < 0.2A. Reference Eqn 1 for (Ιrms) Ιr - In-rush current [A] Τr - In-rush time [sec] Ιs - Switch current [A] Τs - Switch time [sec] Τf - Operation time [sec] 1 Impulsions de courant 6.2.1 Toutes les impulsions de courant doivent être réduites au minimum. Valeur effective (Ιrms) 0.2 A.
PAGE 86
FX2N Series Programmable Controllers 6.2.2 Outputs 6 Triac output example Triac output example 6.2.2 FRE Caractéristiques techniques des sorties triac 6.2.2 GER Beispiel einer Triac-Ausgangsbeschaltung 6.2.2 ITL Dati tecnici delle uscite triac 6.2.2 ESP Ejemplo de una conexión de salida Triac 6.2.2 ENG ENG ☞ Typical wiring GER ☞ Verdrahtungsbeispiel ESP ☞ Ejemplo de cableado Figure 6.
PAGE 87
FX2N Series Programmable Controllers 6.3 Outputs 6 Transistor output specification ENG Transistor output specification 6.3 FRE Caractéristiques techniques des sorties des transistors 6.3 GER Technische Daten der Transistor-Ausgänge 6.3 ITL Dati tecnici delle uscite a transistor 6.3 ESP Datos técnicos de las salidas transistorizadas 6.3 Table 6.
PAGE 88
FX2N Series Programmable Controllers Table 6.
PAGE 89
FX2N Series Programmable Controllers 6.3.1 ENG FRE Outputs 6 Response times Response times 6.3.1 OFF times increase as the load current decreases. For improved response times use a ‘dummy’ resistor, see Figure 6.4. If a response time of 0.5 msec or better is required when using ‘light loads’ use a ‘dummy’ resistor and ensure the signal line has a current greater than 60mA/24V DC. Temps de réponse 6.3.1 Le temps de mise hors circuit augmente au fur et à mesure que le courant de charge augmente.
PAGE 90
FX2N Series Programmable Controllers 6.3.2 Outputs 6 Transistor output example Transistor output example 6.3.2 FRE Exemple d’un câblage de sortie de transistor 6.3.2 GER Beispiel einer Transistor-Ausgangsbeschaltung 6.3.2 ITL Esempio del cablaggio di uscita di un transistor 6.3.2 ESP Ejemplo de una conexión de salida transistorizada 6.3.2 ENG Figure 6.5: FX2N -✩✩MT-ESS, FX2N-✩✩ET-ESS, (Source) +V0 Y0 Y1 +V1 Y1 2 1 Figure 6.
PAGE 91
FX2N Series Programmable Controllers 6.4 ENG Outputs 6 Applying safe loads Applying safe loads 6.4 Ensure all loads are applied to the same side of each PLC output, see previous figures. Loads which should NEVER simultaneously operate (e.g. direction control of a motor), because of a safety critical situation, should not rely on the PLC’s sequencing alone. Mechanical interlocks MUST be fitted to all safety critical circuits. (See preceding figure.
PAGE 92
FX2N Series Programmable Controllers Outputs 6 MEMO 6-14
PAGE 93
Diagnostics 7 FX2N Series Programmable Controllers 7. Diagnostics 7.1 Diagnostics 7. Diagnostic d’erreurs 7. Fehlerdiagnose 7. Diagnostica 7. Diagnóstico de fallos y errores 7. Preliminary checks Preliminary checks 7.1 FRE Vérifications à effectuer avant la mise en service 7.1 GER Überprüfungen vor Betrieb 7.1 ITL Verificaciones preliminares 7.1 ESP Controlli prima del funzionamento 7.1 ENG Table 7.1: REF. POWER RUN BATT.V PROG-E CPU-E POWER RUN BATT.
PAGE 94
FX2N Series Programmable Controllers 7.2 ENG Diagnostics 7 Basic diagnostics Basic diagnostics 7.2 The following diagnostic functions will help identify, common faults. FRE Diagnostic d’erreurs général 7.2 Le diagnostic d’erreurs suivant vous offre une aide pour la recherche et l’élimination des perturbations. GER Allgemeine Fehlerdiagnose 7.2 Die nachfolgende Fehlerdiagnose bietet Ihnen eine Hilfe zum Suchen und Beheben von Störungen. ITL Diagnostica generale 7.
PAGE 95
FX2N Series Programmable Controllers Diagnostics 7 A ENG FRE GER ITL ESP Possible results Résultats possibiles Mögliche Prüfergebnisse Possibili risultati dei controlli Resultados posibies de la prueba deverificación A POWER RUN BATT.V PROG-E CPU-E ENG FRE GER ITL ESP 2 POWER RUN BATT.V 3 PROG-E CPU-E Power LED remains OFF Power LED comes ON Possible fuse blown in the PLC. Contact a Mitsubishi service center for repair work.
PAGE 96
FX2N Series Programmable Controllers 7.2.2 BATT.V LED ON Diagnostics 7 POWER RUN BATT.V PROG-E CPU-E ENG FRE GER ITL ESP BATT.V LED ON 7.2.2 LED BATT.V s’allume 7.2.2 BATT.V-LED leuchtet 7.2.2 Il LED BATT.V si accende 7.2.2 Diodo LED de BATT.V encendido 7.2.2 ENG FRE GER Fault Perturbation Störung Anomalla Fallo / avería LED BATT.V s’allume BATT.V-LED leuchtet Il LED BATT.V si accende Diodo LED de BATT.
PAGE 97
FX2N Series Programmable Controllers Diagnostics 7 B ENG FRE GER ITL ESP Possible results Résultats possibiles Mögliche Prüfergebnisse Possibili risultati dei controlli Resultados posibies de la prueba de verificación 4 B Afficher les données de D8005. La tension de la Monitor D8005. This is batterie actuelle est the current battery affichée (par unités de voltage (in 0.1V units). 0,1 V).
PAGE 98
FX2N Series Programmable Controllers 7.2.3 PROG.E LED flashes Diagnostics 7 POWER RUN BATT.V PROG-E CPU-E ENG FRE GER ITL ESP PROG.E LED flashes7.2.3 LED PROG.E 7.2.3 PROG.E-LED blinkt 7.2.3 LED PROG.E 7.2.3 Diodo LED de PROG.E 7.2.3 ENG FRE Fault GER ITL ESP Perturbation Störung Anomalla Fallo / avería PROG.E LED flashes LED PROG.E PROG.E-LED blinkt LED PROG.E Diodo LED de PROG.E Remedy Remède Abhilfe Rimedio Remedio Check BATT.V LED. Vérifier la LED BATT.V. BATT.
PAGE 99
FX2N Series Programmable Controllers 7.2.4 CPU.E LED ON Diagnostics 7 POWER RUN BATT.V PROG-E CPU-E ENG FRE GER ITL ESP CPU.E LED ON 1 7.2.4 La LED CPU.E est allumée 7.2.4 CPU.E-LED leuchtet 7.2.4 Il LED CPU.E è acceso 7.2.4 Diodo LED de CPU.E encendido 7.2.4 ENG FRE GER ITL Perturbation Störung Anomalla Fallo / avería CPU.E LED ON La LED CPU.E est allumée CPU.E-LED leuchtet Il LED CPU.E è acceso Diodo LED de CPU.
PAGE 100
FX2N Series Programmable Controllers Diagnostics 7 D ENG FRE GER ITL Remedy Remède Abhilfe Rimedio Remedio Staccare il collegamento a terra. Desembornar la conexión de puesta a tierra. Disconnect earth/ground terminal Débrancher le raccordement de terre. ➭➭➭➭ 6 D 7 Erdungsanschluß abklemmen.
PAGE 101
FX2N Series Programmable Controllers Diagnostics 7 F ENG FRE GER ITL ESP Remedy Remède Abhilfe Rimedio Remedio Probabile errore di tempo ciclo nel programma. Controllare il tempo ciclo in D8012. (Le unità da 0,1 ms devono essere inferiori a 0,1 s; valore dati 1000) Probablemente se trata de un fallo de tiempo de ciclo de programa. Comprobar el tiempo de ciclo en D8012.
PAGE 102
FX2N Series Programmable Controllers 7.3 ENG FRE GER ITL ESP Diagnostics 7 Common errors Common errors - Corroded contact points at some point in an I/O line. - An I/O device has been used outside its specified operating range. - An input signal occurs in a shorter time period than that taken by one program scan. - 24V DC power supply is overloaded. 7.3 Autres causes d’erreurs - Contacts corrodés sur les lignes de signalisation E/S.
PAGE 103
FX2N Series Programmable Controllers 7.4 ENG Diagnostics 7 Replacing the battery Replacing the battery 7.4 Turn OFF PLC’s power supply. Remove top cover (Z) from the PLC. Remove battery from holder - disconnect and replace. (This should be carried out in 20s if the current data held in the PLC’s RAM is not to be lost). Refit battery and cover. FRE Remplacement de la batterie 7.4 Couper l’alimentation en tension de l’API. Démonter le couvercle supérieur du boîtier (Z).
PAGE 104
FX2N Series Programmable Controllers 7.5 ENG FRE GER ITL ESP Diagnostics 7 Maintenance Maintenance - Battery has a 5 year life (3 years when used with FX-RAM-8). - Check interior temperature of the panel. - Check panel air filters if fitted. - Check for loosening of terminals or mounting facilities (due to vibration). 7.5 Entretien - Durée de vie de la batterie: 5 ans (3 ans en cas d’utilisation de la FX-RAM-8). - Vérifier la température intérieure de l’armoire électrique.
PAGE 105
FX2N Series Programmable Controllers 7.6 Diagnostics 7 Error flags ON indicates error. ENG Error flags ON indicates error. 7.6 FRE Indicateurs d’erreurs “MARCHE” désigne une erreur. 7.6 GER Fehlermerker EIN bezeichnet einen Fehler. 7.6 ITL Merker di errore ON indica un errore. 7.6 ESP Marcadores de fallos/errores “CONEXION” designa un fallo o error. 7.6 Table 7.2: REF.
PAGE 106
FX2N Series Programmable Controllers Diagnostics 7 ENG ☞ Error flags (M8060 - M8069) FRE ☞ Indicateurs d’erreurs (M8060 - M8069) ITL ☞ Merker di errore (M8060 - M8069) GER ☞ Fehlermerker (M8060 - M8069) ESP ☞ Marcadores de fallos/errores (M8060 - M8069) Table 7.3: REF. ENG FRE GER ITL ESP M8060 (ref. D8060) I/O configuration error Affectation E/S défectueuse E-/A- Zuweisung fehlerhaft Assegnazione I/O errata Asignación E/S errónea M8061 (ref.
PAGE 107
FX2N Series Programmable Controllers 7.7 Diagnostics 7 Error registers ENG Error registers 7.7 FRE Registre d’erreurs 7.7 GER Fehlerregister 7.7 ITL Registri di errore 7.7 ESP Registro de fallos/errores 7.7 Table 7.4: REF.
PAGE 108
FX2N Series Programmable Controllers Table 7.5: Diagnostics 7 FRE ☞ Registre d’erreurs (D8060 - D8069) ENG ☞ Error registers (D8060 - D8069) ITL ☞ Registri di errore (D8060 - D8069) GER ☞ Fehlerregister (D8060 - D8069) ESP ☞ Registro de fallos/errores (D8060 - D8069) REF. ENG FRE GER D8060 Reports location of I/O configuration error (see Figure 7.2) L’affectation d’adresses E/S est défectueuse (voir fig. 7.2) E-/A-Adressenzuweisung ist fehlerhaft (siehe Abb. 7.
PAGE 109
FX2N Series Programmable Controllers 7.8 Diagnostics 7 Error codes ENG Error codes 7.8 FRE Codes d’erreurs 7.8 GER Fehlercodes 7.8 ITL Codici di errore 7.8 ESP Códigos de fallo/error 7.8 Table 7.7: ENG ☞ Error codes (D8061 - D8062) FRE ☞ Codes d’erreurs (D8061 - D8062) ITL ☞ Codici di errore (D8061 - D8062) GER ☞ Fehlercodes(D8061 - D8062) ESP ☞ Códigos de fallo/error (D8061 - D8062) REF.
PAGE 110
FX2N Series Programmable Controllers 7.9 Diagnostics 7 Instruction list ENG Instruction list 7.9 FRE Vue d’ensemble des instructions relatives aux applications 7.9 GER Übersicht der Applikatiosanweisungen 7.9 ITL Elenco delle istruzioni applicative 7.9 ESP Vista de conjunto de las instruciones de aplicación 7.9 Table 7.
PAGE 111
FX2N Series Programmable Controllers Table 7.9: ENG ☞ Alphabetically sorted GER ☞ Alphabetisch sortiert ESP ☞ Clasificación alfabética Symbol A B C 155 ABSD 062 ADD 020 ALT 066 E F 232 - 234, 236 - 238 D P FRE ☞ Classement alphabétique ITL ☞ In ordine alfabetico Symbol G H FNC No. D P Symbol FNC No.
PAGE 112
FX2N Series Programmable Controllers Diagnostics 7 FX2N 8000 steps, FX-RAM-8 = 8K - 16K steps FX-EPROM-8 = 8K -16K steps FX-EEPROM-16 = 4K - 16K steps LD X000 AND Y010 OUT T020 K010 X0 - 327 (256 pnts) X (X+Y) ≤ 256 pnts Max.
PAGE 113
Appendix A: FX2N Series Programmable Controllers Appendix A: Associated Manuals ENG Associated Manuals Appendix A: ITL Further information on programming, programming tools operation, optional modules or special function units/blocks can be found in each respective manual. However, the support language of these manuals is only English.
PAGE 114
FX2N Series Programmable Controllers Table A-1: ENG ☞ GER ☞ ESP ☞ Appendix A: Associated Manuals Weitere Handbücher Otros manuales Manual name Manual No. FRE ☞ ITL ☞ Autres manuels Ulteriori manuali Description FX2N-4DA Special Function Block User’s Guide JY992D65901 ENG This manual contains explanations for wiring, installation, specification and BFM allocation, etc.
PAGE 115
FX2N Series Programmable Controllers Table A-1: ENG ☞ GER ☞ ESP ☞ Appendix A: Associated Manuals Weitere Handbücher Otros manuales Manual name FX Communication (RS232C, RS485) User’s Manual FX2N-32CCL CC-Link Interface Block User’s Manual Manual No.
PAGE 116
FX2N Series Programmable Controllers Appendix A: MEMO A-4
PAGE 117
FX2N Series Programmable Controllers Appendix B: Index ENG A AC powered base units Approvals . . . . . . . . FX2N units . . . . . . . G . . . . . . . . . . . . . . . . . . vii . . . . . . . . . . . . . . . . . . 1-1 General features FX2N units . . . . . . . . . . . . . . . . . . . . . . . . 3-3 I B Base units AC powered (relay/transistor output) . . . . . . 1-1 DC powered (relay/transistor output) . . . . . . 1-1 FX2N physical features . . . . . . . . . . . . . . . . 3-3 Relay output specification .
PAGE 118
Appendix B: Index FX2N Series Programmable Controllers P W Power supply Cable size . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Connection diagram . . . . . . . . . . . . . . . . . 4-11 System isolation . . . . . . . . . . . . . . . . . . . . 4-7 System requirements . . . . . . . . . . . . . . . . 4-9 24V DC service supply . . . . . . . . . . 4-11, 4-13 Wiring Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Caution . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 119
FX2N Series Programmable Controllers Appendix B: Index FRE A D Accessoires des appareil . . . . . . . . . . . . . . . . . . 1-9 Alimentation en tension Caracteristiques des câbles . . . . . . . . . . . . . 4-7 Equipement du système . . . . . . . . . . . . . . . . 4-9 Isolement du système. . . . . . . . . . . . . . . . . . 4-7 Plan de câblage . . . . . . . . . . . . . . . . . . . . . 4-11 Tension de service 24 V CC. . . . . . . . . . . . 4-13 Appareil de Base Appareils FX2N . . . . . . . . . . . . . . .
PAGE 120
Appendix B: Index FX2N Series Programmable Controllers M T Modules d’extension . . . . . . . . . . . . . . . . . . . . . . 1-2 Occupation des bornes, tous types . . . 1-2, 2-4 Modules spéciaux . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Montage Dans le rack (armoire électrique) . . . . . . . . . 3-8 Instruction pour rail DIN . . . . . . . . . . . . . . . 3-11 Instructions générales compte tenu des bruits parasites . . . . . . 3-6 Montage direct . . . . . . . . . . . . . . . . . . . . . .
PAGE 121
FX2N Series Programmable Controllers Appendix B: Index GER A F AC-Grundgerät FX2N-Geräte . . . . . . . . . . . . . . . . . . . . . . . 1-1 Allgemeine Merkmale FX2N-Geräte . . . . . . . . . . . . . . . . . . . . . . . 3-2 Ansprechzeit . . . . . . . . . . . . . . . . . . . 6-1, 6-5, 6-9 Ansprechzeit beim Einsatz eines Transistors . . 6-11 Applikationsanweisung alphabetisch sortiert . . . . . . . . . . . . . . . . . 7-19 numerisch sortiert . . . . . . . . . . . . . . . . . . .
PAGE 122
Appendix B: Index FX2N Series Programmable Controllers M V Montage, allgemeine Hinweise DIN-Schienen-Montage . . . . . . . . . . . . . . . 3-11 DIN-Schienen-Hinweise . . . . . . . . . . . . . . 3-11 Direkte Montage . . . . . . . . . . . . . . . . . . . . 3-12 im Gehäuse (Schaltschrank) . . . . . . . . . . . 3-8 mit Berücksichtigung der Rauscheinwirkung 3-6 Verdrahtung Anschluß der Spannungsversorgung . . . . . 4-11 Anwenderhinweise . . . . . . . . . . . . . . . . . . . 4-2 Erdung . . . . . . . . . . .
PAGE 123
FX2N Series Programmable Controllers Appendix B: Index ITL A Accessori. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 Alimentazione della tensione Allestimento del sitema. . . . . . . . . . . . . . . . . 4-8 Dati caratteristici dei cavi . . . . . . . . . . . . . . 4-13 Isolamento del sistema. . . . . . . . . . . . . . . . 4-13 Schema di cablaggio . . . . . . . . . . . . . . 4-8, 4-11 Tensione di servizio 24 V DC . . . . . . . . . . . 4-13 Allacciamento morsetti Morsetti a vite . . . . .
PAGE 124
Appendix B: Index FX2N Series Programmable Controllers M Manutenzione Cambio della batteria . . . . . . . . . . . . . . . . . 7-11 Manutenzione generale . . . . . . . . . . . . . . . 7-12 Merker di errore. . . . . . . . . . . . . . . . . . . . . . . . . 7-13 Modello Spiegazione del numero di serie . . . . . . . . 1-11 Moduli di ampliamento . . . . . . . . . . . . . . . . . . . . 1-3 Assegnazione dei morsetti, tutti i tipi . . . . . . 2-4 Moduli speciali. . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 125
FX2N Series Programmable Controllers Appendix B: Index ESP A E Accesorios de las unidades . . . . . . . . . . . . . . . . 1-9 Alimentación de tensión Aislamiento del sistema . . . . . . . . . . . . . . . . 4-9 Equipamiento del sistema . . . . . . . . . . . . . . 4-9 Esquema de cableado . . . . . . . . . . . . . . . . 4-11 Paràmetros de cable . . . . . . . . . . . . . . . . . . 4-9 Tensiòn de servicio de 24 V CC . . . . . . . . . 4-13 Entradas, Datos técnicos Cableado de las entradas 110V CA . . . . .
PAGE 126
Appendix B: Index FX2N Series Programmable Controllers O Ocupaciones de bornas Bornas de conexión FX . . . . . . . . . . . . . . . . 2-1 Modulos de ampliacion FX0N todos los tipos . . . . . . . . . . . . . . . . . . . . 2-5 Módulos de amplificación FX2N, todos los tipos . . . . . . . . . . . . . . . . . . . . 2-3 Unidades base FX2N (Salidas de relé, entradas 24V CC) . . . . 2-2 Unidades base FX2N (Salidas de transistorizadas, Entradas de 24V CC) . . . . . . . . . . . . . . .
PAGE 127
FX2N Series Programmable Controllers FRE ENG GER ITL ESP 1 Introduction Introduction Einleitung Introduzione Introducción 1 2 Terminal Layouts Occupation des bornes Klemmenbelegungen Assegnazione Ocupaciones dei morsetti de bornas 2 3 Installation Notes Installation Installation Installazione 3 4 Power supply Alimentation en tension Spannungsversorgung Alimentazione Alimentación della tensione de tensión 4 5 Inputs Entrées Eingänge Ingressi Entradas 5 6 Outputs Sortie
PAGE 128
ENG FRE GER ITL ESP 1 Introduction Introduction Einleitung Introduzione 2 Terminal Layouts Occupation des bornes Klemmenbelegungen Assegnazione Ocupaciones dei morsetti de bornas 3 Installation Notes Installation Installation Installazione 4 Power supply Alimentation en tension Spannungsversorgung Alimentazione Alimentación della tensione de tensión 5 Inputs Entrées Eingänge Ingressi Entradas 6 Outputs Sorties Ausgänge Uscite Salidas 7 Diagnostics Diagnostic d’erreurs
PAGE 129
ENG Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation, use and/or programming of the products associated with this manual. All examples and diagrams shown in this manual are intended as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.
PAGE 130
HARDWARE MANUAL FX2N SERIES PROGRAMMABLE CONTROLLERS HEAD OFFICE: MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100-8310 HIMEJI WORKS: 840, CHIYODA CHO, HIMEJI, JAPAN MODEL FX2N-HW-E MODEL CODE 09R508 JY992D66301J (MEE) Effective Mar. 2003 Specifications are subject to change without notice.