Mitsubishi Electric Corporation Q/QnA Serial Communication Driver 1 System Configuration....................................................................................................... 3 2 Selection of External Device .......................................................................................... 10 3 Example of Communication Setting ............................................................................... 11 4 Setup Items ....................................................
Q/QnA Serial Communication Driver Introduction This manual describes how to connect the Display and the External Device (target PLC). In this manual, the connection procedure will be described by following the below sections: 1 System Configuration This section shows the types of External Devices which can be connected and SIO type. )"1 System Configuration" (page 3) 2 Selection of External Device Select a model (series) of the External Device to be connected and connection method.
Q/QnA Serial Communication Driver 1 System Configuration The system configuration in the case when the External Device of Mitsubishi Electric Corp. and the Display are connected is shown.
Q/QnA Serial Communication Driver Series CPU Q2ASCPU Q2ASCPU-S1 Q2ASHCPU Q2ASHCPU-S1 Link I/F A1SJ71QC24 A1SJ71QC24N A1SJ71QC24-R2 A1SJ71QC24N-R2 A1SJ71QC24 A1SJ71QC24N AJ71QC24 AJ71QC24N AJ71QC24-R2 AJ71QC24N-R2 AJ71QC24 AJ71QC24N MELSEC QnA Example of Communication Settings Cable Diagram RS232C Setting Example 1 (page 11) Cable Diagram 1 (page 39) RS422/485 (4wire) Setting Example 2 (page 14) Cable Diagram 2 (page 41) RS422/485 (4wire) Multilink Setting Example 7 (page 29) Cable Diagra
Q/QnA Serial Communication Driver Connection Configuration • 1:1 Connection External Device Display • 1:n Connection Maximum number of connectable units : 16 units External Device Display • External Device 1:n Connection (when communicating via network) You can access other stations via MELSECNET/H, MELSECNET/10, Ethernet or Q Series C24 unit. Note that you can access only the source station when using the RS232C connector on Q00CPU or Q01CPU.
Q/QnA Serial Communication Driver Setting examples for access beyond the network are shown below. Check the details of the setup items in "Setup Item." )"4 Setup Items" (page 32) External Device1 Display (Station No.5) Network No.1 (MELSECNET/H) External Device11 External Device12 Network No.2 (MELSECNET/10) (PC No.6) External Device22 External Device21 (PC No.8) Serial Communication (I/O No.32) (Station No.15) External Device to be Port No. Station No. Network No. PC No.
Q/QnA Serial Communication Driver • n:1 Connection (Multilink connection) Maximum number of connectable units: 16 units Display Display Display External Device • The maximum number of connectable Displays is 16 units. However, keeping performance in consideration, the number of Displays that can be substantially used is up to 4.
Q/QnA Serial Communication Driver IPC COM Port When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please refer to the IPC manual for details.
Q/QnA Serial Communication Driver DIP switch setting: RS-422/485 (4 wire) DIP switch Setting Description 1 OFF 2 ON 3 ON 4 OFF Output mode of SD (TXD) data: Always output 5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None 6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None 7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available 8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available Reserved (always OFF) SIO type: RS-422/485 *1 *1 9 OFF 10 OFF*1
Q/QnA Serial Communication Driver 2 Selection of External Device Select the External Device to be connected to the Display. Setup Items Setup Description Number of Devices/ PLCs Enter an integer from 1 to 4 for the number of series to set. Manufacturer Select the manufacturer of the External Device to be connected. Select "Mitsubishi Electric Corporation". Series Select a model (series) of the External Device to be connected and connection method. Select "Q/QnA Serial Communication".
Q/QnA Serial Communication Driver 3 Example of Communication Setting Examples of communication settings of the Display and the External Device, recommended by Pro-face, are shown. 3.1 Setting Example 1 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace. • When using A1SJ71QC24N, A1SJ71QC24N-R2, AJ71QC24N or AJ71QC24N-R2, you can set the "Speed" up to 115200.
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When you connect multiple External Device, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device. Important Item When you use 2 types of interface in A1SJ71QC24N, A1SJ71QC24N-R2, AJ71QC24N or AJ71QC24N-R2, please set the total speed of CH1 and CH2 to 115200 or less.
Q/QnA Serial Communication Driver Setting of External Device Use the front switch of the computer link unit to set the communication settings as below.
Q/QnA Serial Communication Driver 3.2 Setting Example 2 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace. • When using A1SJ71QC24N, AJ71QC24N or AJ71QC24N-R4, you can set the "Speed" up to 115200.
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When you connect multiple External Device, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device. Important Item When you use 2 types of interface in A1SJ71QC24N, AJ71QC24N or AJ71QC24N-R4, please set the total speed of CH1 and CH2 to 115200 or less.
Q/QnA Serial Communication Driver Setting of External Device Use the front switch of the computer link unit to set the communication settings as below.
Q/QnA Serial Communication Driver 3.3 Setting Example 3 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When you connect multiple External Device, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device. Important Item When you use 2 types of interface in QJ71C24 or QJ71C24-R2, please set the total speed of CH1 and CH2 to 115200 or less.
Q/QnA Serial Communication Driver Setting of External Device Use the GPP function software by Mitsubishi Electric Corporation to perform the communication settings as below. (1) Double-click [PC Parameter] from [Parameter] to select the [I/O Assign Setting] tab. (2) Click [Type] to select [Intelligent]. (3) Click [Switch Settings] and set as below. Setting Switch Setting Value Switch 1 07E6 Switch 2 0005*1 Mode = Form 5 Switch 5 0000 Station No.
Q/QnA Serial Communication Driver 3.4 Setting Example 4 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When you connect multiple External Device, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device. Important Item When you use 2 types of interface in QJ71C24, please set the total speed of CH1 and CH2 to 115200 or less.
Q/QnA Serial Communication Driver Setting of External Device Use the GPP function software by Mitsubishi Electric Corporation to perform the communication settings as below. (1) Double-click [PC Parameter] from [Parameter] to select the [I/O Assign Setting] tab. (2) Click [Type] to select [Intelligent]. (3) Click [Switch Settings] and set as below. Setting Switch Setting Value Switch 3 07E6 Switch 4 0005*1 Mode = Form 5 Switch 5 0000 Station No.
Q/QnA Serial Communication Driver 3.5 Setting Example 5 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When you connect multiple External Device, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device.
Q/QnA Serial Communication Driver Setting of External Device Use the GPP function software by Mitsubishi Electric Corporation to perform the communication settings as below. (1) Double-click [PC Parameter] from [Parameter] to select [Serial Communication Settings]. (2) Set as below. *1 Setup Items Settings Use Serial Communication Function*1 Use Baud Rate 19.
Q/QnA Serial Communication Driver 3.6 Setting Example 6 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace. • When simultaneously using GP2000 Series during multilink connection, select "QnA Comp. 3C Frame: Format 4" from the "Format".
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When you connect multiple External Device, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device. Important Item When you use 2 types of interface in QJ71C24, please set the total speed of CH1 and CH2 to 115200 or less.
Q/QnA Serial Communication Driver Setting of External Device Use the GPP function software by Mitsubishi Electric Corporation to perform the communication settings as below. (1) Double-click [PC Parameter] from [Parameter] to select the [I/O Assign Setting] tab. (2) Click [Type] to select [Intelligent]. (3) Click [Switch Settings] and set as below. Setting Switch Setting Value Switch 3 07E6 Switch 4 0005*1 Mode = Form 5 Switch 5 0000 Station No.
Q/QnA Serial Communication Driver 3.7 Setting Example 7 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace. • When using A1SJ71QC24N, AJ71QC24N or AJ71QC24N-R4, you can set the "Speed" up to 115200. • When simultaneously using GP2000 Series during multilink connection, select "QnA Comp. 3C Frame: Format 4" from the "Format".
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When you connect multiple External Device, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device. Important Item When you use 2 types of interface in A1SJ71QC24N, AJ71QC24N or AJ71QC24N-R4, please set the total speed of CH1 and CH2 to 115200 or less.
Q/QnA Serial Communication Driver Setting of External Device Use the front switch of the computer link unit to set the communication settings as below.
Q/QnA Serial Communication Driver 4 Setup Items Set communication settings of the Display with GP-Pro EX or in off-line mode of the Display. The setting of each parameter must be identical to that of External Device. )"3 Example of Communication Setting" (page 11) 4.1 When setting with GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Q/QnA Serial Communication Driver Setup Items Setup Description Select the communication frame for the use of MELSEC communication protocol, from "QnA Comp. 3C Frame: Format 4" or "QnA Comp. 4C Frame: Format 5". Format When simultaneously using GP2000 Series during multilink connection, select "QnA Comp. 3C Frame: Format 4" RI/VCC You can switch RI/VCC of the 9th pin when you select RS232C for SIO type. It is necessary to change RI/5V by changeover switch of IPC when connect with IPC.
Q/QnA Serial Communication Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. When [Allowable No. of Device/PLCs] is multiple, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device. Setup Items Setup Description Station No. Use an integer from 0 to 31 to enter the station number of the External Device directly connected to the Display.
Q/QnA Serial Communication Driver 4.2 Communication Settings in Off-line Mode • Refer to the Maintenance/Troubleshooting manual for information on how to enter off-line mode or about the operation. Cf. Maintenance/Troubleshooting Manual "2.2 Off-line Mode" • The number of the setup items to be displayed for 1 page in the off-line mode depends on the Display in use. Please refer to the Reference manual for details.
Q/QnA Serial Communication Driver Setup Items Setup Description Use an integer from 1 to 127 to enter the time (sec) for which the Display waits for the response from the External Device. Timeout In case of communicating via network,please set larger value than the response monitoring time of the relay station for timeout settings. Retry In case of no response from the External Device, use an integer from 0 to 255 to enter how many times the Display retransmits the command.
Q/QnA Serial Communication Driver Device Setting To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device you want to set from the displayed list, and touch [Device]. Setup Items Setup Description Device/PLC Name Select the External Device for device setting. Device name is a title of External Device set with GP-Pro EX.(Initial value [PLC1]) Station No.
Q/QnA Serial Communication Driver Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device you want to set from the displayed list, and touch [Option]. Setup Items RI/VCC Setup Description You can switch RI/VCC of the 9th pin when you select RS232C for SIO type. It is necessary to change RI/5V by changeover switch of IPC when connect with IPC. Please refer to the manual of the IPC for more detail.
Q/QnA Serial Communication Driver 5 Cable Diagram The cable diagram shown below may be different from the cable diagram recommended by Mitsubishi Electric Corp. Please be assured there is no operational problem in applying the cable diagram shown in this manual. • The FG pin of the External Device body must be D-class grounded. Please refer to the manual of the External • SG and FG are connected inside the Display. When connecting SG to the External Device, design the system Device for more details.
Q/QnA Serial Communication Driver 1C) Display side Terminal block Display Shield External Device side D-sub 9 pin (plug) Signal name Pin Signal name RD(RXD) 3 SD(TXD) SD(TXD) 2 RD(RDX) ER(DTR) 6 DSR(DR) SG 5 SG RS(RTS) 1 CD CS(CTS) 4 DTR(ER) 8 CS(CTS) Shell FG GP-Pro EX Device/PLC Connection Manual 40
Q/QnA Serial Communication Driver Cable Diagram 2 Display (Connection Port) GP3000*1 (COM1) AGP-3302B (COM2) ST*2 (COM2) IPC*3 Cable 2A COM port conversion adapter by Pro-face CA3-ADPCOM-01 + Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01 + User-created cable 2B User-created cable 2C Online adapter by Pro-face CA4-ADPONL-01 + Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01 + User-created cable 2D Online adapter by Pro-face CA4-ADPONL-01 + User-created
Q/QnA Serial Communication Driver 2A) • 1:1 Connection Sdqlhm`k aknbj Chrok`x B@2,@COBNL,/0 Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V B@2,@COSQL,/0 Dwsdqm`k Cduhbd rhcd Rghdkc Rhfm`k m`ld Rhfm`k m`ld QC@ RC@ QCA RCA RC@ QC@ RCA QCA RF RF Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V EF Trdq,bqd`sdc b`akd • 1:n Connection Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Chrok`x B@2,@COBNL,/0 B@2,@COSQL,/0 Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.
Q/QnA Serial Communication Driver 2B) • 1:1 Connection Chrok`x rhcd C,rta 8 ohm 'rnbjds( Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Chrok`x • Rghdkc Dwsdqm`k Cduhbd rhcd Ohm Rhfm`k m`ld Rhfm`k m`ld 0 QC@ RC@ 1 QCA RCA 2 RC@ QC@ 6 RCA QCA 4 RF RF 3 DQ@ EF 7 BR@ 8 DQA 5 BRA Rgdkk EF Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V 1:n Connection Chrok`x rhcd C,rta 8 ohm 'rnbjds( Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Chrok`x Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.
Q/QnA Serial Communication Driver 2C) • 1:1 Connection Sdqlhm`k aknbj Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Chrok`x B@3,@CONMK,/0 B@2,@COSQL,/0 Rghdkc Rhfm`k m`ld Dwsdqm`k Cduhbd rhcd Rhfm`k m`ld QC@ RC@ QCA RCA RC@ QC@ RCA QCA RF RF Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V EF Trdq,bqd`sdc b`akd • 1:n Connection Sdqlhm`k aknbj Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Chrok`x B@3,@CONMK,/0 Sdqlhm`shnm qdrhrs`mbd B@2,@COSQL,/0 22/Ω 0.
Q/QnA Serial Communication Driver 2D) • 1:1 Connection C,rta 8 ohm 'oktf( Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Dwsdqm`k Cduhbd rhcd Ohm Rhfm`k m`ld Rhfm`k m`ld 1 QC@ RC@ 6 QCA RCA 2 RC@ QC@ 7 RCA QCA 4 RF RF Rgdkk EF EF Chrok`x B@3,@CONMK,/0 Rghdkc Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Trdq,bqd`sdc b`akd • 1:n Connection C,rta 8 ohm 'oktf( Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V B@3,@CONMK,/0 Chrok`x Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.
Q/QnA Serial Communication Driver 2E) • 1:1 Connection Display side Terminal block Termination resistance*1 Display Shield External Device side Signal name Signal name RDA SDA RDB SDB SDA RDA SDB RDB SG SG ERA FG Termination resistance 330Ω 1/4W CSA ERB CSB *1 The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the rear of the Display as shown in the table below. • DIP Switch No.
Q/QnA Serial Communication Driver Cable Diagram 3 Display (Connection Port) Cable Notes GP3000 (COM1) ST (COM1) IPC*1 PC/AT 3A Mitsubishi Q connection cable by Pro-face CA3-CBLQ-01 (5m) or RS-232C cable by Mitsubishi Electric Corp. QC30R2 (3m) or RS-232C cable for QCPU connection by Diatrend Corp. DQCABR2V-H GP-4105 (COM1) 3B Mitsubishi PLC Q Series CPU I/F Cable by Pro-face ZC9CBQ31(3m) *1 Available to order the length of DQCABR2V-H by Diatrend Corp. up to 15m.
Q/QnA Serial Communication Driver Cable Diagram 4 Display (Connection Port) GP3000 (COM1) ST (COM1) IPC*1 PC/AT GP-4105 (COM1) *1 Cable Notes 4A RS-232C cable by Pro-face CA3-CBL232/5M-01 (5m) 4B User-created cable 4C User-created cable The cable length must be 15m or less. Only the COM port which can communicate by RS-232C can be used.
Q/QnA Serial Communication Driver 4C) External Device side D-sub 25 pin (plug) Display side Terminal block Display Shield Pin Signal name RD(RXD) 2 SD(TXD) SD(TXD) 3 RD(RXD) ER(DTR) 6 DSR(DR) SG 7 SG RS(RTS) 8 CD CS(CTS) 20 DTR(ER) 5 CS(CTS) 1 FG Signal name GP-Pro EX Device/PLC Connection Manual 49
Q/QnA Serial Communication Driver Cable Diagram 5 Display (Connection Port) GP3000*1 (COM1) AGP-3302B (COM2) ST*2 (COM2) IPC*3 Cable 5A COM port conversion adapter by Pro-face CA3-ADPCOM-01 + Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01 + User-created cable 5B User-created cable 5C Online adapter by Pro-face CA4-ADPONL-01 + Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01 + User-created cable 5D Online adapter by Pro-face CA4-ADPONL-01 + User-created
Q/QnA Serial Communication Driver 5A) Sdqlhm`shnm qdrhrs`mbd 22/Ω 0.3V Dwsdqm`k Cduhbd rhcd C,rta 14 ohm 'oktf( Sdqlhm`k aknbj Chrok`x B@2,@COBNL,/0 B@2,@COSQL,/0 Rghdkc Rhfm`k m`ld Ohm Rhfm`k m`ld QC@ 2 RC@ QCA 05 RCA RC@ 1 QC@ RCA 04 QCA RF 6 RF RF 7 RF 1/ RF 10 RF 3 CRQ@ 4 CSQ@ 06 CRQA 07 CSQA 0 EF Trdq,bqd`sdc b`akd • As the External Device has the termination resistance built-in, you do not need to connect the termination resistance.
Q/QnA Serial Communication Driver 5C) Dwsdqm`k Cduhbd rhcd C,rta 14 ohm 'oktf( Sdqlhm`k aknbj Sdqlhm`shnm qdrhrs`mbd Rhfm`k m`ld 22/Ω 0.3V Rghdkc Ohm Rhfm`k m`ld QC@ 2 RC@ QCA 05 RCA RC@ 1 QC@ RCA 04 QCA RF 6 RF RF 7 RF 1/ RF 10 RF 3 CRQ@ 4 CSQ@ 06 CRQA 07 CSQA 0 EF Chrok`x B@3,@COBNL,/0 B@2,@COSQL,/0 Trdq,bqd`sdc b`akd • As the External Device has the termination resistance built-in, you do not need to connect the termination resistance.
Q/QnA Serial Communication Driver 5D) External Device D-sub 25 pin (plug) Display side D-sub 9 pin (plug) Termination resistance 330Ω 1/4W Display CA4-ADPONL-01 Pin Signl name 2 Shield Pin Signl name RDA 3 SDA 7 RDB 16 SDB 3 SDA 2 RDA 8 SDB 15 RDB 5 SG 7 SG 8 SG 20 SG 21 SG 4 DSRA 5 DTRA 17 DSRB 18 DTRB 1 FG User-created cable • As the External Device has the termination resistance built-in, you do not need to connect the termination resistance.
Q/QnA Serial Communication Driver 5E) External Device side D-sub 25 pin (plug) Display side Terminal block Termination resistance*1 Display Shield Pin Signal name RDA 3 SDA RDB 16 SDB SDA 2 RDA SDB 15 RDB SG 7 SG ERA 8 SG CSA 20 SG ERB 21 SG CSB 4 DSRA 5 DTRA Signal name 17 DSRB 18 DTRB 1 FG • As the External Device has the termination resistance built-in, you do not need to connect the termination resistance.
Q/QnA Serial Communication Driver Cable Diagram 6 Display (Connection Port) Cable 6A COM port conversion adapter by Pro-face CA3-ADPCOM-01 + Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01 + User-created cable 6B COM port conversion adapter by Pro-face CA3-ADPCOM-01 + Multilink cable by Pro-face CA3-CBLMLT-01 + User-created cable 6C User-created cable 6D Online adapter by Pro-face CA4-ADPONL-01 + Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01 + User-cre
Q/QnA Serial Communication Driver 6A) Terminal block Termination resistance 330 Ω 1/4W Termination resistance 330 Ω 1/4W Terminal block Shield External Device side Terminal block Termination Signal resistance name 330 Ω SDA 1/4W Shield Signal name Signal name RDA RDA RDB RDB SDB SDA SDA RDA SDB SDB RDB SG SG SG TRM FG FG CA3-ADPTRM-01 CA3-ADPTRM-01 CA3-ADPCOM-01 CA3-ADPCOM-01 Display Termination resistance 330 Ω 1/4W Display User-created cable 6B) Sdqlhm`k aknbj 'L2 rbqdv( Sdq
Q/QnA Serial Communication Driver 6C) Sdqlhm`k qdrhrs`mbd 22/ Ω 0.3V Chrok`x rhcd C,rta 8 ohm 'rnbjds( Chrok`x Sdqlhm`k qdrhrs`mbd 22/ Ω 0.3V Sdqlhm`k aknbj 'L2 rbqdv( Rghdkc Rghdkc Sdqlhm`k aknbj 'L2 rbqdv( Rghdkc Dwsdqm`k Cduhbd rhcd Sdqlhm`k aknbj Sdqlhm`k Ohm Rhfm`k m`ld Rhfm`k m`ld Rhfm`k m`ld 0 QC@ QC@ QC@ 1 QCA QCA QCA 2 RC@ RC@ RC@ QC@ Rhfm`k m`ld qdrhrs`mbd 22/ Ω RC@ 0.
Q/QnA Serial Communication Driver 6E) Sdqlhm`k aknbj 'L2 rbqdv( Sdqlhm`shnm qdrhrs`mbd 22/ Ω 0.3V Sdqlhm`shnm qdrhrs`mbd 22/ Ω 0.3V Sdqlhm`k aknbj 'L2 rbqdv( Rghdkc Rhfm`k m`ld Rghdkc Rhfm`k m`ld Dwsdqm`k Cduhbd rhcd Sdqlhm`k aknbj Sdqlhm`shnm Rhfm`k qdrhrs`mbd m`ld 22/ Ω RC@ 0.3V QC@ QC@ QCA QCA RCA RC@ RC@ QC@ RCA RCA QCA RF RF RF EF EF EF B@2,BAKLKS,/0 B@2,BAKLKS,/0 B@3,@CONMK,/0 B@3,@CONMK,/0 Chrok`x Sdqlhm`shnm qdrhrs`mbd 22/ Ω 0.
Q/QnA Serial Communication Driver 6G) Display side Terminal block Terminal resistance*1 Terminal resistance*1 *1 Shield Display side Terminal block Shield External Device side Terminal block Terminal Signal name Signal name RDA RDA RDB RDB SDA SDA RDA SDB SDB RDB SG SG SG ERA ERA FG CSA CSA ERB ERB CSB CSB Display Display Signal name resistance 330 Ω SDA 1/4W SDB Terminal resistance 330 Ω 1/4W The resistance in the Display is used as the termination resistance.
Q/QnA Serial Communication Driver 6 Range of Supported Device Address Range of supported device address is shown in the table below. Please note that the actually supported range of the devices varies depending on the External Device to be used. Please check the actual range in the manual of your External Device. MELSEC Q (High performance model, Basic model) / MELSEC QnA Series This address can be specified as system data area.
Q/QnA Serial Communication Driver Device File Register (0R - 31R) *2 Bit Address Word Address - 0R0000-0R32767 - 1R0000-1R32767 - 2R0000-2R32767 : : - 30R0000-30R32767 - 31R0000-31R26623 32bits Notes *1 *1 It is different by the memory card which uses the range of file register. *2 Set the block No. on the head of device name. This is the device name for conversion with GP-Pro/PB III for Windows.
Q/QnA Serial Communication Driver MELSEC Q (Universal model) Series This address can be specified as system data area. Device First 5 digits of the serial No. in the CPU unit: Less than 10042 First 5 digits of the serial No.
Q/QnA Serial Communication Driver First 5 digits of the serial No. in the CPU unit: Less than 10042 Device First 5 digits of the serial No.
Q/QnA Serial Communication Driver 7 Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type in data displays.
Q/QnA Serial Communication Driver 8 Error Messages Error messages are displayed on the Display screen as follows: "No.: Device Name: Error Message (Error Occurrence Area)". Each description is shown below. Item Description No. Error No. Device Name Name of the External Device where error occurs. Device name is a title of the External Device set with GP-Pro EX. (Initial value [PLC1]) Error Message Displays messages related to the error which occurs.
Q/QnA Serial Communication Driver GP-Pro EX Device/PLC Connection Manual 66
