User`s manual

A - 6 A - 6
3.4.7 Offset/gain setting mode and offset/gain specification (buffer memory addresses 22, 23:
Un\G22, Un\G23) .............................................................................................................................. 3-24
3.4.8 Offset/gain adjustment value specification (buffer memory address 24: Un\G24) ......................... 3-24
3.4.9 Offset/gain range setting (buffer memory address 25: Un\G25) ..................................................... 3-25
3.4.10 CH
output monitor value (buffer memory addresses 38, 39: Un\G38, Un\G39).......................3-25
3.4.11 Rate control enable/disable setting (buffer memory address 46: Un\G46)................................... 3-25
3.4.12 Disconnection detection/warning output setting (buffer memory address 47: Un\G47)............... 3-26
3.4.13 Warning output flag (buffer memory address 48: Un\G48) ...........................................................3-26
3.4.14 Disconnection detection flag (buffer memory address 49: Un\G49) ............................................. 3-27
3.4.15 CH
increase/decrease digital limit values (buffer memory addresses 70 to 73:
Un\G70 to Un\G73) .........................................................................................................................3-27
3.4.16 CH
warning output upper limit value/lower limit value (buffer memory addresses 86 to 89:
Un\G86 to Un\G89) .........................................................................................................................3-27
3.4.17 Mode switching setting (buffer memory addresses 158, 159: Un\G158, Un\G159).....................3-28
3.4.18 Pass data classification setting (buffer memory addresses 200: Un\G200) ................................. 3-28
3.4.19 Industrial shipment settings and user range settings offset/gain values
(buffer memory addresses 202 to 217: Un\G202 to Un\G217) ..................................................... 3-29
4 SETUP AND PROCEDURES BEFORE OPERATION 4- 1 to 4-13
4.1 Handling Precautions............................................................................................................................... 4- 1
4.2 Setup and Procedures before Operation ................................................................................................ 4- 2
4.3 Part Identification Nomenclature ............................................................................................................. 4- 3
4.4 Wiring........................................................................................................................................................4- 5
4.4.1 Wiring precautions.............................................................................................................................4- 5
4.4.2 External wiring...................................................................................................................................4- 6
4.5 Switch Setting for Intelligent Function Module........................................................................................ 4- 7
4.6 Offset/Gain Settings................................................................................................................................. 4- 9
5 UTILITY PACKAGE (GX Configurator-DA) 5- 1 to 5-29
5.1 Utility Package Functions ........................................................................................................................5- 1
5.2 Installing and Uninstalling the Utility Package......................................................................................... 5- 2
5.2.1 User precautions ............................................................................................................................... 5- 2
5.2.2 Operating environment...................................................................................................................... 5- 4
5.3 Explanation of Utility Package Operation................................................................................................ 5- 5
5.3.1 How to perform common utility package operations........................................................................ 5- 5
5.3.2 Operation overview ........................................................................................................................... 5- 8
5.3.3 Starting the intelligent function module utility ................................................................................... 5-10
5.4 Initial Setting.............................................................................................................................................5-13
5.5 Automatic Refresh Setting .......................................................................................................................5-14
5.6 Monitor/Test .............................................................................................................................................5-16
5.6.1 Monitor/test screen............................................................................................................................5-16
5.6.2 Offset/gain setting operation.............................................................................................................5-19
5.6.3 Confirmation of Conversion Characteristic.......................................................................................5-21
5.6.4 Pass data...........................................................................................................................................5-23
5.7 FB Conversion of Initial Setting/Auto Refresh Setting ............................................................................5-25
5.8 Usage of FB ............................................................................................................................................. 5-26
5.8.1 Outline................................................................................................................................................5-26
5.8.2 Paste an FB to a Sequence Program............................................................................................... 5-28
5.8.3 Convert (Compile) a Sequence Program ......................................................................................... 5-29