Page 1 of 54 Technical Service Bulletin SUBJECT: ACCESSORY REMOTE ENGINE START No: TSB−11−66−001 DATE: October, 2011 MODEL: See below CIRCULATE TO: [ ] GENERAL MANAGER [ X ] PARTS MANAGER [ X ] TECHNICIAN [ X ] SERVICE ADVISOR [ X ] SERVICE MANAGER [ ] WARRANTY PROCESSOR [ ] SALES MANAGER PURPOSE This TSB contains technical information and troubleshooting for the accessory Remote Engine Start system for affected vehicles.
Page 2 of 54 TSB−11−66−001 D Key removed from ignition (for KOS equipped vehicles, the ignition switch is in the LOCK position) D Transmitter within approximately 150 feet of the vehicle After the engine is started with the Remote Engine Start transmitter, it will stop if any of the following conditions are detected: D A door (or liftgate/trunk) is opened D The accelerator pedal is pressed (except Endeavor, Galant and Eclipse models) D The engine hood is opened.
Page 3 of 54 TSB−11−66−001 Replacement Transmitters: When ordering a replacement for the MZ360271EX or MZ360272EX original transmitter, a newer one, MZ360361EX will be provided. The features on the new transmitter will be limited to the same functions as the older one that was provided in the kit. To program the replacement transmitter for MZ260271EX, see MZ360360EX Programming. To program the replacement transmitter for MZ360272EX, see MZ360340EX Programming.
Page 4 of 54 TSB−11−66−001 Wire Routing NOTE: Detailed installation instructions are on the Mitsubishi Dealer Link. (See Additional Resources at the end of this TSB). Eclipse, Eclipse Spyder, Galant, Endeavor Remote Engine Start Kit Part No.
Page 5 of 54 TSB−11−66−001 WIRING DIAGRAM A Galant Harness Layout (Top View) Remote Start p/n: MZ360271EX & MZ360360EX Endeavor Harness Layout (Top View)
Page 6 of 54 TSB−11−66−001 WIRING DIAGRAM A (continued) Remote Start p/n: MZ360271EX & MZ360360EX Eclipse/Eclipse Spyder Harness Layout (Top View)
Page 7 of 54 TSB−11−66−001 Lancer, Lancer Sportback, Lancer Evolution, Outlander, Outlander Sport Remote Engine Start Kit Part No. MZ360340EX/MZ360272EX Note: Detailed installation instructions can be found on the MITSUBISHI DEALER LINK. (See Additional Resources at the end of this TSB for details on accessing these instructions). Note: A hood switch (MZ360316EX) will have to be installed on Lancer/Lancer Sportback produced before 1/31/2010 and 2010-2011 Lancer DE.
Page 8 of 54 TSB−11−66−001 Part No.
Page 9 of 54 TSB−11−66−001 Remote Engine Start Transmitter Operation Before operating the transmitter, verify that: The shifter is in the “P” (Parking) position. All doors (including the rear gate and spare tire carrier) are securely closed. The engine hood is securely closed The vehicle key is removed from the ignition switch. For vehicles equipped with the F.A.S.T. Key, the ignition switch is on the LOCK position.
Page 10 of 54 TSB−11−66−001 Switch Lock The remote for the MZ360360EX and MZ360340EX accessory parts have a switch lock function.
Page 11 of 54 TSB−11−66−001 Setting Engine Idling Time Once a vehicle is started by the remote engine start system, the engine, if left undisturbed, will continue to idle for a set time. This is referred to as “Engine Idling Time.” The factory default setting is 10 minutes. It can be adjusted as shown below. Part Number MZ360271EX/ MZ360272EX Setting Idling Time The idling time can be set to 5, 10, 20 or 30 minutes. The initial setting at shipment is 10 minutes.
Page 12 of 54 TSB−11−66−001 Part Number MZ360360EX/ MZ360340EX Setting Idling Time 1 Press Function switch and Start switch at the same time until the buzzer sounds. 10 minutes Mark or 30 minutes Mark will blink according to the default setting. 10 MINUTES Preset setting is 10 minutes 2 Press Start switch to set the idling time. The selected idle time Mark blinks. (Example shows 30 minutes idle time) 30 MINUTES If the Mark stops blinking and turns off, retry from Step 1.
Page 13 of 54 TSB−11−66−001 Programming the RKE System No. MZ360271EX MZ360272EX MZ360340EX MZ360360EX Response 1 Close all doors and hatch, but open hood. Turn off ignition and remove key. Close all doors, hood and hatch. Turn off ignition and remove key. Close all doors, hood and hatch. Turn off ignition and remove key. Close all doors and N/A hatch, but open hood. Turn off ignition and remove key. 2 Insert ignition key. Turn the key to ACC position.
Page 14 of 54 TSB−11−66−001 Programming the KOS System No. MZ360272EX MZ360340EX Response 1 Close all doors, hood and hatch. Get into the vehicle and make sure the ignition is OFF. Remove the knob cap. Insert emergency key. N/A 2 Turn emergency key to ACC position, then back to Lock (OFF) 5 times within 10 seconds. Then remove the key. ECU beeps once. 3 Within 10 seconds after the beep sounds, press the 3 buttons on the transmitter all at once and hold for 2 seconds or longer.
Page 15 of 54 TSB−11−66−001 Programming the Keyless Push Start System − Part No. MZ360340EX No. Action Response 1 Close all doors, hood, and hatch. Get into the vehicle and make sure the ignition is OFF. N/A 2 Press the Engine Start button once, then wait for 3 to 5 seconds. The indicator light on the transmitter switch changes to orange. 3 Press the Engine Start button twice. The indicator light on the transmitter switch turns off.
Page 16 of 54 TSB−11−66−001 Common Remote Engine Start Issues CONCERN SUGGESTIONS Cannot program Remote Engine Start transmitter Verify that the vehicle is not affected by the incorrect wiring instructions for 2009 & later Endeavors and 2010 & later Eclipse/Eclipse Spyder covered later in this bulletin. See programming instructions (RKE, KOS, Push Button) and also Tech Line Video on Programming Verify correct installation (MZ360360EX, MZ360340EX, MZ360272EX, MZ360271EX).
Page 17 of 54 TSB−11−66−001 How to change the engine idling time in the Remote Engine Start system? See Setting Engine Idle Time MZ360360EX/MZ360340EX, MZ360272EX/MZ360271EX . Can a second transmitter be programmed to the Remote Engine Start system? No. For safety reasons, only one remote can be programed to a specific remote engine start system at one time. However, a replacement transmitter can be programmed. See Replacement Transmitters. Engine shuts off when the driver’s door is opened.
Page 18 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 1 of 11) (Eclipse, Eclipse Spyder, Galant, Endeavor) Perform troubleshooting E to L and confirm proper installation of the accessory. Once confirmed, perform operation check.
Page 19 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 2 of 11) Operation check 2: Perform the following procedures: Note: On Endeavor models, be sure to set the interior light switch to the “ROOM” position before proceeding.
Page 20 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 21 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 4 of 11) Refer to Wiring Diagram A for connector references. See “Checking Harnesses” at the end of this section.
Page 22 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 5 of 11) Refer to Wiring Diagram A for connector references. Return to Troubleshooting Part No.
Page 23 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 6 of 11) If the vehicle does not have a 20A fuse for the engine starter harness, go to Troubleshooting F. Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section.
Page 24 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 7 of 11) Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section. Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section.
Page 25 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 8 of 11) Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section.
Page 26 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360271EX (page 9 of 11) Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section.
Page 27 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 28 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 29 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360272EX (page 1 of 6) (Lancer, Lancer Sportback, Outlander, Outlander Sport) Perform Troubleshooting steps B to D and confirm proper installation of the accessory. Once confirmed, perform the operation check.
Page 30 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360272EX (page 2 of 6) Operation Check 2: Check the vehicle. Refer to the vehicle’s service manual. Check the vehicle. Refer to the vehicle’s service manual.
Page 31 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360272EX (page 3 of 6) While registering the Remote Engine Start transmitter, if the Remote Engine Start ECU is found unresponsive (does not beep as indicated in the registration process), perform Troubleshooting B. Check the vehicle. Refer to the vehicle’s service manual.
Page 32 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360272EX (page 4 of 6) Refer to Wiring Diagram B for connector references. While programming the Remote Engine Start transmitter, if the keyless operation key is unresponsive, perform Troubleshooting C. Go to Troubleshooting D. Check the vehicle. Refer to the vehicle’s service manual. Troubleshooting D Check the vehicle. Refer to the vehicle’s service manual.
Page 33 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 34 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 35 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360340EX (page 1 of 7) (Lancer, Lancer Sportback, Outlander, Outlander Sport) Perform Troubleshooting B to D and confirm proper installation of the accessory. Once confirmed, perform the operation check. Operation Check: Go to Troubleshooting A Check the vehicle. Refer to the vehicle’s service manual. Check the vehicle. Refer to the vehicle’s service manual.
Page 36 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360340EX (page 2 of 7) OK Troubleshooting complete. Return to Operation Check.
Page 37 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360340EX (page 3 of 7) Refer to Wiring Diagram B for connector references. While registering the Remote Engine Start transmitter, if the Remote Engine Start ECU is unresponsive (does not beep as indicated in the registration process), perform Troubleshooting B. Check the vehicle. Refer to the vehicle’s service manual.
Page 38 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360340EX (page 4 of 7) While programming the Remote Engine Start transmitter, if the keyless operation key is unresponsive, perform Troubleshooting C. Go D D. GototoTroubleshooting Troubleshooting Check the vehicle. Refer to the vehicle’s service manual.
Page 39 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360340EX (page 5 of 7) Refer to Wiring Diagram B for connector references. Troubleshooting D. Check the vehicle. Refer to the vehicle’s service manual.
Page 40 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360340EX (page 6 of 7) Circuit Diagram 2 4 2 4 ANT 1 +B (to Main Unit) +B GND (to Main Unit) GND 5 +B(IN) ACC(IN) 3 SERIAL_OUT 6 SERIAL_IN GND(IN) ACC (from RF unit) ACC (to Main unit) 5 6 3 1 Connector drawings indicate the terminal layout as seen from the arrow direction.
Page 41 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 42 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360360EX (page 1 of 11) (Eclipse/Spyder, Galant, Endeavor) Note: On Endeavor models, be sure to set the interior light switch to the “ROOM” position before proceeding. Perform troubleshooting E to L and confirm proper installation of the accessory. Once confirmed, perform operation check.
Page 43 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 44 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 45 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360360EX (page 4 of 11) Refer to Wiring Diagram A for connector references.
Page 46 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360360EX (page 5 of 11) Refer to Wiring Diagram A for connector references.
Page 47 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360360EX (page 6 of 11) If the vehicle does not have a 20A fuse for the engine starter harness, go to Troubleshooting F. Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section.
Page 48 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360360EX (page 7 of 11) Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section. If the vehicle is a Galant, go to Troubleshooting H. Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section.
Page 49 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360360EX (page 8 of 11) Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section.
Page 50 of 54 TSB−11−66−001 Troubleshooting Part No. MZ360360EX (page 9 of 11) Refer to Wiring Diagram A for connector references. Perform the remaining connector terminal check. See “Checking Harnesses” at the end of this section. Continue to perform Operation Checks 1 and 2.
Page 51 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 52 of 54 TSB−11−66−001 Troubleshooting Part No.
Page 53 of 54 TSB−11−66−001 Correction to Remote Engine Start Installation Instructions for Eclipse/Spyder/Endeavor Remote Engine Start (MZ360271EX & MZ360360EX) Instructions Correction – 2009 & later Endeavor, 2010 & later Eclipse/Eclipse Spyder. Wire color descriptions in the installation instructions for the section “ROUTING THE HARNESS TO THE COMBINATION METER” are incorrect for affected vehicles listed above only. The wire colors in the pin diagram are correct.
Page 54 of 54 TSB−11−66−001 Additional Resources 1. Remote Engine Start installation and basic troubleshooting information are on the Mitsubishi Dealer Link: a. b. c. d. e. Log onto the Mitsubishi Dealer Link. Under the “Parts” tab, click on “accessories”. On the left side of the screen, click on “Parts & Accessories Guide”. Select the appropriate vehicle model year. Enter the Remote Engine Start Kit part number (see part number listing earlier in this bulletin). 2.
