Specifications
● 各部の名称と設定 AJ65BT-64AD
Signal source: 0 to 20mA
For wire, use two-core shielded twisted-pair cable.
Indicates the input resistance of AJ65SBT-64AD and AJ65BT-64AD, respectively.
Connect a capacitor of around 0.1 to 0.47 µF (it must be a product that can withstand voltag-
es of 25 V or more) between the V and COM terminals if noise or ripple is generated in the
external wiring.
Be sure to ground FG1. There are cases where AG should also be grounded if the signal is
particularly noisy.
The offset or gain value should be set again if the ground wiring is changed after setting the
offset or gain value (whether the signals were connected to ground or not).
1
2
3
4
Master/Local
Remote I/OAnalog
High-Speed
Counters
PositioningHMIRepeatersRS-232
Interfaces
OptionSoftwareOthers
Technical
Information
CC-Link
-
CC-Link / LT
Bridge Modules
Support PC
Interfaces
Peripheral
Device
Connection
77
In case of voltage input
Signal source: 0 to 10V
In case of current input
Signal source: 0 to 20mA
Analog Modules AJ65SBT-64AD AJ65BT-64AD
AJ65SBT-64AD ● Name and Setting of Each Part
AJ65BT-64AD ● Name and Setting of Each Part
AJ65SBT-64AD ●
External Dimention Diagram
AJ65BT-64AD ●
External Dimention Diagram
Unit: mm
0
19
2
3
8
7
46
5
0
1
2
3
46
5
0
1
2
3
4
OFFSET
GAIN DOWN
UPMODE RESET
B RATE STATION NO.
X10 X1
PW
RUN
L RUN
SD
RD
L ERR.
AJ65BT 64RD
Two4.5mm
mounting holes
SET
SW
0
1-4
9
MODE
NORMAL
TEST CH.
TEST
4
0
19
2
3
Two 4.5 mm x 5.1 mm mounting holes
(for M4 mounting screws)
PW RUN L RUN L ERR. CH1 2 OFFSET GAIN
MITSUBISHI
AJ65SBT-64AD
DA DG +24V 24G
DB SLD (FG)
TEST
TEST V+
I+
AGV+ I+
CH1 CH2
SELECT
SET
STATION NO. B RATE
40 20 10 8
4 2 1 4 2 1
ON
34
(FG1)
COMSLDCOM
V+ I+
V+ I+
COMSLDCOM
CH3 CH4
(4.5)
Unit: mm
C
D
A
B
MITSUBISHI
STATION NO.
X10 X1
5
0
1
46
2
3
5
0
1
46
9
2
37
8
1
4
2
3
CH. OFFSET GAIN RESET
MELSEC AJ65BT-64AD
0
1
4
2
3
B RATE
PW
RUN
L RUN
SD
RD
L ERR.
DA DG
CH1
V+
CH2
V+
CH3
I+ SLD
CH4
I+ SLD FG1
1 3 5 7 9 111315171921232527
COMCOM24G+24V
DB SLD
CH1
I+
CH2
I+
CH3
V+
CH4
V+ AG
2 4 6 8 10 12 14 16 18 20 22 24 26
(FG) TEST TEST SLD
COM COM
The analog input range is set as follows:
Use D when 0 to 20 mA is used.
Station number setting switches
Transmission speed setting switch
Channel selector switch
OFFSET switch
Analog input range
setting pins
GAIN switch
RESET switch
PW LED
RUNLED
SD LED
RD LED
L ERR. LED
LED name Item checked
0
1
2
3
4
Other than
0 to 4
156 kbps (factory setting)
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
Not used (L ERR. LED turns on
and a communication error occurs.)
Setting
number
Transmission speed
A
B
C
D
Voltage
010V
15V
1010V
05V
Current
020mA
420mA
2020mA
020mA
On: When the power supply is
turned on
On: Normal operationNormal
mode
Turns on during data reception
On: Communication data error
Turns on during data transmission
L RUN LED
On: When the communication is
normal
Operating condition
LED display
Terminal block
PW RUN L RUN L ERR. CH1 2 OFFSET GAIN
MITSUBISHI
AJ65SBT-64AD
DA DG +24V 24G
DB SLD (FG)
TEST
TEST V+
I+
AGV+ I+
CH1 CH2
SELECT
SET
STATION NO. B RATE
40 20 10 8
4 2 1 4 2 1
ON
34
(FG1)
COMSLDCOM
V+ I+
V+ I+
COMSLDCOM
CH3 CH4
Operating condition LED display
LED display
for offset/gain adjustment
SELECT/SET switch
Terminal block DIN rail hook
PW
RUN
L RUN
L ERR.
LED name Item checked
On: When the power supply is
turned on
On: Normal opera-
tion
Normal
mode
CH
OFFSET
GAIN
Always off
Normal
mode
On: When the transmission
speed or station number set-
ting is outside the range
On: When the communication
is normal
Station number setting switches
1
2
3
4
10
11
64
40
OFF
OFF
OFF
OFF
OFF
OFF
ON
20
OFF
OFF
OFF
OFF
OFF
OFF
ON
10
OFF
OFF
OFF
OFF
ON
ON
OFF
8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
OFF
OFF
OFF
OFF
ON
2
OFF
ON
ON
OFF
OFF
OFF
OFF
1
ON
OFF
ON
OFF
OFF
ON
OFF
Station
no.
0
1
2
3
4
10-digit Unit-digit
Transmission speed
setting switches
Setting
value
Setting switch
Transmission
speed
4
OFF
OFF
OFF
OFF
ON
2
OFF
OFF
ON
ON
OFF
1
OFF
ON
OFF
ON
OFF
156 kbps
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
The compact remote I/O module
power supply, transmission, and I/O
signals are connected here.
● AJ65SBT-64AD/AJ65BT-64AD External Connection Diagram
Product
Description