Specifications

Motor Dimensions
27
● HA-LFS601 (B)
● HA-LFS701M (B)
● HA-LFS11K2 (B), HA-LFS11K24 (B)
● HA-LFS801 (B), HA-LFS12K1 (B), HA-LFS8014 (B) (special-order)
(Note 7)
, HA-LFS12K14 (B) (special-order)
(Note 7)
● HA-LFS11K1M (B), HA-LFS15K1M (B), HA-LFS11K1M4 (B), HA-LFS15K1M4 (B)
● HA-LFS15K2 (B), HA-LFS22K2 (B), HA-LFS15K24 (B), HA-LFS22K24 (B)
Unit: mm (inch)
Notes:
1. Use a friction coupling to fasten the load.
2. For dimensions where there is no tolerance listed, use general tolerance.
3. Dimensions inside < > are for models with electromagnetic brake.
4. Only for models with electromagnetic brake.
5. Leave a clearance of at least 100mm between the motor's suction side and wall.
6. Make sure that oil, water and dust, etc., will not enter the motor from the lead-in hole.
7. The motors are special-order products. Contact Mitsubishi for details on the servo amplifier type and the types of servo motors that are combined with the servo amplifier, and for information
on the delivery schedule.
* When the motor is used without a hanger, plug the thread hole with a bolt of M10✕20 (0.7874) or less.
* When the motor is used without a hanger, plug the thread hole with a bolt of M12x20 (0.7874) or less.
M200 (7.87)
171 (6.73)
142 (5.59)
55 (2.17)
Hanger screw hole
Bolt: M10x20 (0.7874) (Note 4)
45°
4-ø14.5 (0.571)
mounting hole
Use hexagonal cap
head bolts.
Brake connector pin assignment
MS3102A10SL-4P (Note 4)
Exhaust air
480 (18.9) <550 (21.65)> 85 (3.35)
426 (16.77) <498 (19.61)>
262 (10.31) <334 (13.15)>
93 (3.66)
80 (3.15)
3 (0.12)
(Note 4)
(Note 4)
(Note 4)
20 (0.79)
ø42h6 (ø1.6535 )
102 (4.02)
ø180h7 (ø7.0866 )
3-hanger (M10) (Note 6)
Brake connector
MS3102A10SL-4P (Note 4)
Encoder connector
MS3102A20-29P
Oil seal
S50689B (in standard case)
S45629B (with electromagnetic brake)
M8 screw
5.2
(0.205)(0.78)
19.8
Motor flange direction
Brake
AB
206 (8.11) 6 (0.24)6 (0.24)
146 (5.75)
ø44 (ø1.732) hole
Cooling fan
rotating direction
Suction air
0 -0.0006
0 -0.0018
(Note 4)
27 (1.06)11 (0.43)
ø215
(ø8.465)
ø250
(ø9.843)
Brake connector pin assignment
MS3102A10SL-4P (Note 4)
Motor flange direction
Brake
AB
45°
4-ø14.5 (0.571)
mounting hole
Use hexagonal cap
head bolts.
M250 (9.84)
140 (5.51)
200 (7.87)
Encoder connector
MS3102A20-29P
25 (0.98)
111.5 (4.39)
5 (0.2)
100 (3.94)
ø230h7 (ø9.0551 )
60 (2.36)
ø55m6 (ø2.1654 )
6.6
(0.26)
20.4
(0.803)
M10 screw
110 (4.33)L
Exhaust air
Oil seal
S709513B (in standard case)
S60829B (with electromagnetic brake)
205 (8.07)
376 (14.8)
180 (7.09)
250 (9.84) 6 (0.24)6 (0.24)
27 (1.06)
Suction air
M254 (10.0)
209 (8.23)
Cooling fan
rotating direction
3-hanger (M12) (Note 6)
(Note 4)
(Note 4)
(Note 4)
Brake connector
MS3102A10SL-4P (Note 4)
Hanger screw hole
Bolt: M12x22 (0.87) (Note 4)
Hanger screw hole
Bolt: M12x22 (0.87) (Note 4)
60 (2.36)
Model
L
495 (19.49)
<610 (24.02)>
555 (21.85)
<670 (26.38)>
1500r/min
HA-LFS11K1M (B)
HA-LFS11K1M4 (B)
HA-LFS15K1M (B)
HA-LFS15K1M4 (B)
2000r/min
HA-LFS15K2 (B)
HA-LFS15K24 (B)
HA-LFS22K2 (B)
HA-LFS22K24 (B)
HA-LFS12K1 (B)
HA-LFS12K14 (B) (special-order)
HA-LFS801 (B)
HA-LFS8014 (B) (special-order)
1000r/min
Variable dimensions
ø44 (ø1.732) hole
0 -0.0018
0.0012 0.0004
ø265
(ø10.433)
ø
30
0
(ø11.811)