Installation Manual

Eng-20
5. Function settings (continued)
No.36
Outdoor temperature display setting
Set to display outdoor temperature detected by Lossnay unit
thermistor.
This function is N/A from Lossnay unit DIP-SW.
This function is available only when “Sensor value” is set to “Yes”
(Display) by the remote controller PZ-62DR-E.
DIP-SW
Setting
check
PZ-62DR-E
Setting
check
Outdoor temperature
display
SW No. Setting Function No. Setting Data
N/A
- -
36
0 N/A
- -
1
(Factory setting)
Available on the screen
of PZ-62DR-E
No.37
Indoor temperature display setting
Set to display indoor temperature detected by Lossnay unit thermistor.
This function is N/A from Lossnay unit DIP-SW.
This function is available only when “Sensor value” is set to “Yes”
(Display) by the remote controller PZ-62DR-E.
DIP-SW
Setting
check
PZ-62DR-E
Setting
check
Indoor temperature
display
SW No. Setting Function No. Setting Data
N/A
- -
37
0 N/A
- -
1
(Factory setting)
Available on the screen
of PZ-62DR-E
No.38
CO2 concentration display setting
Set to display CO2 concentration when the CO2 sensor (PZ-70CSB-E,
PZ-70CSW-E) is used.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
PZ-62DR-E
Setting
check
CO2 concentration
display
SW No. Setting Function No. Setting Data
N/A
- -
38
0 N/A
- -
1
(Factory setting)
Available on the screen
of PZ-62DR-E
- This function is available only when “Sensor value” is set to “Yes”
(Display) by the remote controller PZ-62DR-E.
- When displaying CO2 concentration, supply air temperature cannot
be displayed simultaneously.
- CO2 concentration display shows the value detected by a CO2
sensor connected to Lossnay unit. The value may di󰀨er from the
actual indoor CO2 concentration. This function cannot be used as a
measuring instrument.
- The value may signicantly di󰀨er from the actual indoor CO2
concentration for approx. 15 minutes after starting operation.
- When 3rd party’s CO2 sensor is connected, CO2 concentration is
not displayed on PZ-62DR-E screen.
No.39
Calculated supply air temperature display
setting
Set to display calculated supply air temperature or not.
This function is N/A from Lossnay unit DIP-SW.
In addition, this function is available only when “Sensor value” is set
to “Yes”(Display) by the remote controller PZ-62DR-E.
CO2 concentration and supply air temperature can not be displayed
at the same time.
DIP-SW
Setting
check
PZ-62DR-E
Setting
check
Calculated supply air
temperature display
SW No. Setting Function No. Setting Data
N/A
- -
39
0
(Factory setting)
N/A
- - 1
Available on the screen
of PZ-62DR-E
- CO2 concentration and supply air temperature can not be displayed
at the same time.
No.40, 41
Temperature exchange e󰀩ciency
setting
Set the 10 digit of temperature exchange e󰀩ciency which is used to
calculate supply air temperature.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
PZ-62DR-E
Setting
check
10 digit of temperature
exchange e󰀩ciency
SW No. Setting Function No. Setting Data
N/A
- -
40
0 0
- - 1 1
- - 2 2
- - 3 3
- - 4 4
- - 5 5
- - 6 6
- -
7
(Factory setting)
7
- - 8 8
- - 9 9
DIP-SW
Setting
check
PZ-62DR-E
Setting
check
1 digit of temperature
exchange e󰀩ciency
SW No. Setting Function No. Setting Data
N/A
- -
41
0
(Factory setting)
0
- - 1 1
- - 2 2
- - 3 3
- - 4 4
- - 5 5
- - 6 6
- - 7 7
- - 8 8
- - 9 9
No.42
Outdoor temperature correction
Set the correction for the outdoor temperature displayed on the
PZ-62DR-E screen by function
No. 36
.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
PZ-62DR-E
Setting
check
The correction to
thermistor detection
SW No. Setting Function No. Setting Data
N/A
- -
42
0 -7 K (-12.6 °F/-7 °C )
- - 1 -6 K (-10.8 °F/-6 °C )
- - 2 -5 K (-9 °F/-5 °C )
- - 3 -4 K (-7.2 °F/-4 °C )
- - 4 -3 K (-5.4 °F/-3 °C )
- - 5 -2 K (-3.6 °F/-2 °C )
- - 6 -1 K (-1.8 °F/-1 °C )
- -
7
(Factory setting)
0 K (0 °F/0 °C )
- - 8 +1 K (+1.8 °F/+1 °C )
- - 9 +2 K (+3.6 °F/+2 °C )
- - 10 +3 K (+5.4 °F/+3 °C )
- - 11 +4 K (+7.2 °F/+4 °C )
- - 12 +5 K (+9 °F/+5 °C )
- - 13 +6 K (+10.8 °F/+6 °C )
- - 14 +7 K (+12.6 °F/+7 °C )