HG-A Series Hail Guard Installation Manual

ManualsBrandsMitsubishi ManualsCoolingHail Guard

Table Of Contents

INSTALLATION MANUAL

For safe and effective use of this kit, please read this installation manual thoroughly before installing these components

FOR INSTALLER

MANUFACTURED FOR:

MITSUBISHI ELECTRIC US, INC.

M-Series and P-Series Outdoor Units

for use with:

HG-A1, HG-A2, HG-A3, HG-A4

Hail Guard

Summary of content (8 pages)

PAGE 1
MANUFACTURED FOR: MITSUBISHI ELECTRIC US, INC.
PAGE 2
Contents Contents.................................................................................................. 2 1. Dimensions ......................................................................................... 2 2. Inspect Shipment ................................................................................ 4 3. Safety Precautions ............................................................................. 4 4. Installation Considerations ....................................................
PAGE 3
Table 2: HG-A1 HG-A2 HG-A3 HG-A4 Rear Side Rear Side Rear Side Kit kg (lbs) Weight kg 7.49 4.61 9.99 5.20 9.45 5.35 3.23 (lbs) (16.51) (10.17) (22.02) (11.46) (20.83) (11.79) (7.13) mm 965 947 1310 1250 1313.2 1296.2 470 (in) (37.99) (37.28) (51.57) (49.21) (51.7) (51.03) (18.5) mm 737.25 299 791 208 726 207 701 (in) (29.03) (11.77) (31.14) (8.19) (28.58) (8.15) (27.6) mm 332 326 332 326 332 326 201 (in) (13.07) (12.83) (13.07) (12.
PAGE 4
2. Inspect Shipment Upon receipt of equipment, carefully inspect it for possible damage. Take special care to examine the unit if the carton is damaged. If damage is found, it should be noted on the carrier’s freight bill. Damage claims should be filed with the carrier immediately. Claims of shortages should be filed with the seller within 5 days. 3. Safety Precautions Carefully read this section, always observe for safety, and securely install the optional parts.
PAGE 5
. Checking Parts Note: Screws for all models are included, therefore some screws will not be used. HG-A1 HG-A2 HG-A3 REAR GUARD Description Rear Guard Side Guard Mounting Screws HG-A4 Description Side Guard Mounting Screws Qty 1 1 13 for A1 13 for A2 19 for A3 SIDE GUARD Mounting Screw M5 x 10 Qty 1 2 HG-A4 Mounting Screw #8 x 1/2 6. Installation Instructions HG-A1, -A2, Rear Guard Step 0. Remove the existing screws. Step 0 5 © 2016 Mitsubishi Electric US, Inc.
PAGE 6
HG-A1, -A2, -A3 Rear Guard Step 1. Loosening the screws in the top panel. Slide the top of the hail guard under the screw head and re-tighten enough to support the hail guards as you align the holes with the holes in the outdoor unit. Step 2. Loosely tighten the hail guard with the screws provide. Step 3. Check the alignment, and fully tighten the screws. HG-A1, -A2, -A3 Side Guard Step 1. Align side hail guard holes with existing screw holes on the outdoor unit and secure with screws provided.
PAGE 7
HG-A4 Step 1. Insert the right side lip of the hail guard between the right side of the plastic grill and the edge of the outdoor unit cabinet. SCALE 0.250 Step 2. Rotate the hail guard clockwise and loosely secure the left side with the existing screws. Existing Screws EXISTING SCREWS SCALE 0.250 Step 3. Align the holes on the right side of the hall with the existing holes on the outdoor unit and secure with the screws provided. Provided Screws PROVIDED SCREWS SCALE 0.
PAGE 8
This product is designed and intended for use in the residential and light-commercial environment. Please be sure to put the contact address/telephone number on this manual before handing it to the customer. Manufactured for MITSUBISHI ELECTRIC US, INC. www.mitsubishielectric-usa.