User`s manual
Table Of Contents
- SAFETY PRECAUTIONS
- CONDITIONS OF USE FOR THE PRODUCT
- REVISIONS
- INTRODUCTION
- CONTENTS
- ABOUT MANUALS
- HOW TO USE THIS MANUAL
- ABOUT THE GENERIC TERMS AND ABBREVIATIONS
- PACKING LIST
- 1. OVERVIEW
- 2. SYSTEM CONFIGURATION
- 3. FUNCTION LIST
- 4. INSTALLATION AND UNINSTALLATION
- 5. SCREEN MAKEUP AND BASIC OPERATIONS
- 6. PROJECT CREATION
- 7. SYSTEM CHECKING FROM PERIPHERAL DEVICE
- 8. DATA SETTING
- 9. WRITING TO/READING OF/VERIFICATION OF POSITIONING MODULE DATA
- 10. POSITIONING DEBUGGING
- 11. USEFUL FUNCTIONS
- APPENDIX
- Appendix 1 Read from Module/Write to Module Reference Processing Times
- Appendix 2 Restrictions Depending on Function Version of QD75
- Appendix 3 Functions Added to/Changed from the Previous Versions
- Appendix 4 Uninstalling the License Key FD
- Appendix 5 Parameter Names Shown in GX Configurator-QP Screens and Manuals
- INDEX
Appendix - 3 Appendix - 3
MELSOFT
A
PPENDICES
Applicable Version Added to /Changed Function Description Refer To
GX Configurator-QP
Version 2.27D
Operating environment
• Microsoft
R
Windows Vista
R
Home Basic Operating System is
added to the operating systems.
• Microsoft
R
Windows Vista
R
Home Premium Operating System
is added to the operating systems.
• Microsoft
R
Windows Vista
R
Business Operating System is
added to the operating systems.
• Microsoft
R
Windows Vista
R
Ultimate Operating System is added
to the operating systems.
• Microsoft
R
Windows Vista
R
Enterprise Operating System is
added to the operating systems.
Section
2.2
Applicable programmable
controller CPU
"Q02PHCPU, Q06PHCPU, Q13UDHCPU, Q26UDHCPU,
Q03UDECPU, Q04UDEHCPU, Q06UDEHCPU, Q13UDEHCPU,
Q26UDEHCPU" are added.
Chapter 1
GX Configurator-QP
Version 2.29F
Servo parameters
• MR-J3 full closed servo series parameters are added.
• MR-J3 servo linier series parameters are added.
—
Connection Setup
• "Ethernet direct" is added to the personal computer side
interface.
• The default value of "Timeout time" for "RS232-C" or "USB"
setting is changed to 10 seconds.
Section
7.1
GX Configurator-QP
Version 2.30G
Servo parameters
The method for executing the default (initial) settings for each
servo amplifier series selected is changed.
Chapter 1
Applicable programmable
controller CPU
• "Q00UJCPU, Q00UCPU, Q01UCPU, Q10UDHCPU,
Q20UDHCPU, Q10UDEHCPU, and Q20UDEHCPU" are added.
• C Controller module, "Q12DCCPU-V" is added.
Chapter 1
GX Configurator-QP
Version 2.32J
Connection setup The GOT transparent mode is added.
Section
7.1.1
Change module type LD75P4, LD75D4, and LD77MH4 are supported. —
Applicable programmable
controller CPU
L02CPU and L26CPU-BT are added. Chapter 1
GX Configurator-QP
Version 2.34L
Operating environment
• Microsoft
R
Windows
R
7 Starter Operating System is added to
the operating systems.
• Microsoft
R
Windows
R
7 Home Premium Operating System is
added to the operating systems.
• Microsoft
R
Windows
R
7 Professional Operating System is
added to the operating systems.
• Microsoft
R
Windows
R
7 Ultimate Operating System is added to
the operating systems.
• Microsoft
R
Windows
R
7 Enterprise Operating System is added
to the operating systems.
Section
2.2
GX Configurator-QP
Version 2.35M
Operating Environment 64-bit Windows
R
7 is supported.
Section
2.2
: The applicable version can be confirmed in Product information. For details, refer to "Section 11.10 Help".