User`s manual

ManualsBrandsMitsubishi ManualsTV Converter BoxGX Configurator-AD

201

202

203

204

205

206

207

208

209

210

Table Of Contents

SAFETY PRECAUTIONS
CONDITIONS OF USE FOR THE PRODUCT
REVISIONS
INTRODUCTION
CONTENTS
ABOUT MANUALS
HOW TO USE THIS MANUAL
ABOUT THE GENERIC TERMS AND ABBREVIATIONS
PACKING LIST
1. OVERVIEW
- 1.1 Features
- 1.2 Manual Makeup
2. SYSTEM CONFIGURATION
- 2.1 System Configuration
- 2.2 Operating Environment
- 2.3 Instructions for use of older version of GX Configurator-QP
3. FUNCTION LIST
- 3.1 Function List
- 3.2 Menu List
4. INSTALLATION AND UNINSTALLATION
- 4.1 Installation
- 4.2 Uninstallation
- 4.3 Starting GX Configurator-QP
- 4.4 Exiting GX Configurator-QP
5. SCREEN MAKEUP AND BASIC OPERATIONS
- 5.1 Screen Makeup and Display Selection
- 5.2 Basic Operations
6. PROJECT CREATION
- 6.1 Creating a New Project
- 6.2 Opening the Existing Project
- 6.3 Saving the Project
- 6.4 Closing the Project
- 6.5 Deleting the Project
- 6.6 Reading other Format Files
  - 6.6.1 Reading SW1RX/IVD/NX-AD75P / GX Configurator-AP format file
  - 6.6.2 Reading the CSV format file
- 6.7 Write to CSV Format File
7. SYSTEM CHECKING FROM PERIPHERAL DEVICE
- 7.1 Connection Setup
  - 7.1.1 Setting for connection via GOT (GOT transparent mode)
- 7.2 System Monitor
- 7.3 Checking the Positioning Module Function Version (OS Information)
- 7.4 Checking Connect
8. DATA SETTING
- 8.1 Parameter Setting
- 8.2 Servo Parameter Setting
- 8.3 Positioning Data Setting
  - 8.3.1 Positioning data
  - 8.3.2 M code comment
- 8.4 Simulation
- 8.5 Block Start Data Setting
  - 8.5.1 Block start data
  - 8.5.2 Condition data
- 8.6 Error Check
9. WRITING TO/READING OF/VERIFICATION OF POSITIONING MODULE DATA
- 9.1 Write to Module/Read from Module/Verify Module Data
- 9.2 Servo Amplifier Data Read
- 9.3 Flash ROM write request
- 9.4 Module Initialization
10. POSITIONING DEBUGGING
- 10.1 Error Check Module Data
- 10.2 Monitor
- 10.3 Sampling Monitor
  - 10.3.1 Sampling signal monitor
  - 10.3.2 Sampling buffer monitor
- 10.4 Test
- 10.5 Servo On/Off
11. USEFUL FUNCTIONS
- 11.1 Useful Functions for Projects
- 11.2 Edit Functions for Data Setting
- 11.3 Copying the Data
  - 11.3.1 Copying the data on an axis basis (Axis copy)
  - 11.3.2 Block start copy
- 11.4 Navigation Function
- 11.5 Option Setting
- 11.6 Printing the Project Data
  - 11.6.1 Printer setting
  - 11.6.2 Printing
- 11.7 Positioning Data Setting in Test Mode
  - 11.7.1 Teaching
  - 11.7.2 Positioning data test edit
- 11.8 Wave Trace
  - 11.8.1 Wave trace condition setting
  - 11.8.2 Wave trace execution
- 11.9 Location Trace
  - 11.9.1 Location trace condition setting
  - 11.9.2 Location trace execution
- 11.10 Help
APPENDIX
- Appendix 1 Read from Module/Write to Module Reference Processing Times
- Appendix 2 Restrictions Depending on Function Version of QD75
- Appendix 3 Functions Added to/Changed from the Previous Versions
- Appendix 4 Uninstalling the License Key FD
- Appendix 5 Parameter Names Shown in GX Configurator-QP Screens and Manuals
INDEX

11 - 33 11 - 33

MELSOFT

11. USEFUL FUNCTIONS

11.8 Wave Trace

Using the wave trace function in the trace mode, show the speed command (axis

speed) for positioning operation as waveform data.

(Note that the QD75M, QD75MH and LD77 cannot be used.)

11.8.1 Wave trace condition setting

PURPOS

To execute the wave trace, set the trace starting condition and the data to be

traced.

BASIC OPERATIO

1. Choose Wave trace.

Double-click. Double-click.

2. Click the "Setting" button in the wave trace window.

3. Set the Trace interval, Trace trigger, Stop condition, axis and data to be traced

in the Trace setting dialog box.

4. Click the "OK" button in the Trace setting dialog box.

5. For the tracing operation that follows, refer to Section 11.8.2.

DISPLAY/SETTING SCREE