User`s manual

ManualsBrandsMitsubishi ManualsTV Converter BoxGX Configurator-AD

111

112

113

114

115

116

117

118

119

120

Table Of Contents

SAFETY PRECAUTIONS
CONDITIONS OF USE FOR THE PRODUCT
REVISIONS
INTRODUCTION
CONTENTS
ABOUT MANUALS
HOW TO USE THIS MANUAL
ABOUT THE GENERIC TERMS AND ABBREVIATIONS
PACKING LIST
1. OVERVIEW
- 1.1 Features
- 1.2 Manual Makeup
2. SYSTEM CONFIGURATION
- 2.1 System Configuration
- 2.2 Operating Environment
- 2.3 Instructions for use of older version of GX Configurator-QP
3. FUNCTION LIST
- 3.1 Function List
- 3.2 Menu List
4. INSTALLATION AND UNINSTALLATION
- 4.1 Installation
- 4.2 Uninstallation
- 4.3 Starting GX Configurator-QP
- 4.4 Exiting GX Configurator-QP
5. SCREEN MAKEUP AND BASIC OPERATIONS
- 5.1 Screen Makeup and Display Selection
- 5.2 Basic Operations
6. PROJECT CREATION
- 6.1 Creating a New Project
- 6.2 Opening the Existing Project
- 6.3 Saving the Project
- 6.4 Closing the Project
- 6.5 Deleting the Project
- 6.6 Reading other Format Files
  - 6.6.1 Reading SW1RX/IVD/NX-AD75P / GX Configurator-AP format file
  - 6.6.2 Reading the CSV format file
- 6.7 Write to CSV Format File
7. SYSTEM CHECKING FROM PERIPHERAL DEVICE
- 7.1 Connection Setup
  - 7.1.1 Setting for connection via GOT (GOT transparent mode)
- 7.2 System Monitor
- 7.3 Checking the Positioning Module Function Version (OS Information)
- 7.4 Checking Connect
8. DATA SETTING
- 8.1 Parameter Setting
- 8.2 Servo Parameter Setting
- 8.3 Positioning Data Setting
  - 8.3.1 Positioning data
  - 8.3.2 M code comment
- 8.4 Simulation
- 8.5 Block Start Data Setting
  - 8.5.1 Block start data
  - 8.5.2 Condition data
- 8.6 Error Check
9. WRITING TO/READING OF/VERIFICATION OF POSITIONING MODULE DATA
- 9.1 Write to Module/Read from Module/Verify Module Data
- 9.2 Servo Amplifier Data Read
- 9.3 Flash ROM write request
- 9.4 Module Initialization
10. POSITIONING DEBUGGING
- 10.1 Error Check Module Data
- 10.2 Monitor
- 10.3 Sampling Monitor
  - 10.3.1 Sampling signal monitor
  - 10.3.2 Sampling buffer monitor
- 10.4 Test
- 10.5 Servo On/Off
11. USEFUL FUNCTIONS
- 11.1 Useful Functions for Projects
- 11.2 Edit Functions for Data Setting
- 11.3 Copying the Data
  - 11.3.1 Copying the data on an axis basis (Axis copy)
  - 11.3.2 Block start copy
- 11.4 Navigation Function
- 11.5 Option Setting
- 11.6 Printing the Project Data
  - 11.6.1 Printer setting
  - 11.6.2 Printing
- 11.7 Positioning Data Setting in Test Mode
  - 11.7.1 Teaching
  - 11.7.2 Positioning data test edit
- 11.8 Wave Trace
  - 11.8.1 Wave trace condition setting
  - 11.8.2 Wave trace execution
- 11.9 Location Trace
  - 11.9.1 Location trace condition setting
  - 11.9.2 Location trace execution
- 11.10 Help
APPENDIX
- Appendix 1 Read from Module/Write to Module Reference Processing Times
- Appendix 2 Restrictions Depending on Function Version of QD75
- Appendix 3 Functions Added to/Changed from the Previous Versions
- Appendix 4 Uninstalling the License Key FD
- Appendix 5 Parameter Names Shown in GX Configurator-QP Screens and Manuals
INDEX

8 - 10 8 - 10

MELSOFT

8. DATA SETTING

HELPFUL OPERATION (2)

Perform the following operation when you want to determine the command speed

from the time needed to complete positioning. Use the axis speed calculation

function to calculate the command speed from the travel distance, acceleration

time, deceleration time, time needed for positioning completion and so on.

(Note that the QD75M, QD75MH and LD77 cannot be used.)

1. Open the positioning data edit window of the corresponding axis. (Active status)

2. Click the [Edit]

[Speed of axis setting] menu.

3. Set the Rating, Feedback, Start position, End position, Operation interval and

Data No. in the Axis speed calculation dialog box, and choose ACC interval and

DEC interval.

4. Click the "Calculation" button to show the operation result in the Confirmation

dialog box.

5. Click "OK" in the Confirmation dialog box to change the command speed to that

of the operation result.

[Axis speed calculation dialog box]

[Confirmation dialog box]