Specifications

1091
FDC-HKXR
TB Tr
L
1
L
2
L
3
N
52C
CNA1 CNA2
Noise filter
LED1 LED2
Red Green
Control board
Transformer
~ ~ ~
+
1 2 3 4 5 6 7
1 2 3 4 5 6 7
Cn1
Cn1
Cn5
CT
R1
Cn2
Cn13
Cn14
Cn7
Cn8
Cn9
Cn10
Cn11
Cn12
Resistance
module
LD1 LD2 LD3 LD4
Green Red Red Red
Inverter circuit board
1234
+
+
1236710111415 12345691214
Cn3
23F
Outdoor Unit Check Points Check the part marked * while the power supply is turned ON. Make checks after the power supply is turned OFF, or after removing each part. Power cable check: To see if there is continuity and connections are correct.
Noise filter check: There should be continuity.
Fuse check: There should be continuity.
7
Power check: Measure the power at the L1, L2, L3
and N on the terminal block TB.
*
Diode module check
When the tester bars are re- versed, the resistance value is about 10 ~ 20 Ω
Transformer check: Disconnect the connector CNA1. There should be continuity on the primary side.
6
5
+
~+
~
When the
result is OK
Tester bar
8
4
Reactor continuity check: After disconnecting the connector and make a continuity check. At that time, there should be continuity.
FDCP2001, 2501 6.8 Ω
*
Normality LED2 check: If this LED flashing, the operation of the microcomputer is normal.
When a check is made at the connector Cn1, the values become usually as shown in the following table.
Cn1
1 2 3 4 5 6 7
Contents of communication
Common
12 V power supply
Transmission from outdoor unit
Reception from outdoor unit
Watch dog (communication from the inverter
circuit board to the outdoor unit PCB)
Inverter overheating
Current cut
V (analog tester)
0V
12V
Swings between 11V and 11.5V.
Swings between 4.5V and 5V.
Swings between 2V and 4V.
5V: normal, 0V: abnormal 5V: normal, 0V: abnormal
Connector
Check the appeaeance for damage and blister and check the charging characteristic with a tester. (The indicator swings and returns slowly. After changing the polarity, perform the same operation. If the indicator returns, this is regarded as normal.)
Power transistor output check:
Disconnect the Faston terminal of the compressor and measure the output voltage. (The output 2001 is for the case whese the inverter is not loaded.)
Unit: V (AC)
FDC 2001, 2501 type
35Hz
95~98
40Hz
104~107
65Hz
167~173
75Hz
180~190
80Hz
195~197
95Hz
198~203
Frequency
Modells
Check the appearance for crack or damage.
2
3
Mark
Tester bar
(red)
Tester bar
(black)
Power transistor module
CM
U
V
W
Inverter PCB output check: Disconnect the connector and mea- sure the signal output to the power transistor module.
(+)
Cn13- 6
Cn13-10 Cn13-14
Cn14- 4 Cn14- 5 Cn14- 6
(-)
Cn13- 7
Cn13-11 Cn13-15
Cn14- 1 Cn14- 2 Cn14- 3
Voltage
DC 1.5 ~
1.6V
Tester bars
1
*
*
LD1 check:
When this LED flashing every 0.5 second, it is normal. LD2: Power transistor overheating LD3: Current cut LD4: Serial transmission error On the above occasion, these LDs light up.
DC280V
Capacitor check:
Resistor R1 inspection