Operation Manual

EN-23
Menu operation (continued)
2. INSTALLATION menu
@ -* ANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP MODE has been chosen, the
defa:19 ANDARD lamp mode is switched to the LOW lamp mode in 1 minute.
@n A!! , &:).4is 8*1*(9*)<-*39-*35:94:7ce .8.35:9 -*&:).4of A!AUAU&3)$ cannot
be selected.
@ o cancel the test pattern, press any button.
eFgnitteSnoitpo uneM ature description
WALL SCREEN

 
BLUE
 N
 /BLA
BOAR# ARD
Selects a desired setting based on the color of the screen or wall
on which images are projected. When selecting a setting other
than BLACAR# ARD, you can fine-tune the color
tone to the desired level on the 1 to 5 scale. (See page 18.)
LAMP MODE
 ANDARD
Select this setting when you want to view images in a well-lit
room.
LOW
Select this setting when you want to view images at a moderate
light intensity. -e operating sound is consequently reduced, and
the lamp lifetime becomes longer.
@#hen this mode is switched, projected images may flicker.
@f this mode is frequently switched, the lamp may be deterio-
rated.
 ANDBY MODE
 ANDARD
(&3'*&(9.;&9*).3  ! 
cannot be activated.
LOW
Power consumption can be lowered when selecting LOW. How-
ever, LAN &3) ! (&3349'*&(9.vated.
AU!
AU 
+AU  is selected, selects AU<-*39-*.35:984:7ce is
! 8*1*(98AU<-*39-*.35:984:rce is COM-
! 8*1*(98!<-*39-*.35:984:rce is "-
"O,8*1*(98<-*39-*.35:984:7ce.8.
AU!! elect the audio input.
$
*1*(98$8.,3&14+!&3)!You can change the
balance of AUA!:8.3,$ .
AU  POWER ON ON/OFF
When this mode is set to ON, the lamp is automatically lit when
the power cord is plugged in the wall outlet. Select ON when you
set the projector at the ceiling.
@#hen the lamp is off, the projector is in standby. Use the
remote control to turn on the lamp.
AU  POWER OFF OFF/5-60 min
Selects a desired timer setting until the projector enters the
standby mode when there is no signal input from the source.
 !  ! Use to capture the screen for the splash scre*3**5&,*
SPLASH SCREEN ON/OFF
Select ON to display the splash screen when the projector is pow-
ered on.
BA BLUE/BLACE
Selects the background color that is displayed when there is no
signal input from the source.
AV !  BLA
Use to choose the background, either BLAC47E,
which
will be displayed when the AV! button is pressed. When
E is chosen, the splash screen will be displayed.
E REVERSE
OFF
Select this setting when you want to view images from the front
with the projector set on the floor.
RROR
Select this setting when you want to view images from behind the
screen with the projector set on the floor.
"
Select this setting when you want to view images from behind the
screen with the projector set at the ceiling.
"
Select this setting when you want to view images from the front
with the projector set at the ceiling.
 PA 
CROSS HA 
Select to show the test cross hatch pattern.
LAMP MODE
OFF
IMAGE
REVERSE
CROSS HATCH
WALL SCREEN
BEIGE
STANDBY MODE
STANDARD
STANDARD
AUDIO INPUT
AUTO
opt.
INSTALLATION
AUTO POWER
OFF
OFF
OFF
AUTO POWER
ON
IMAGE CAPTURE
ON
SPLASH
SCREEN
ON
BACK COLOR
BLUE
AV MUTE MODE
TEST PATTERN
BLACK
SETUP
WHITE
Select to show the maximum brightness image.
BLACK
Select to show the minimum brightness image.